6 research outputs found
Virgo calibration and reconstruction of the gravitational wave strain during VSR1
No full textVirgo is a kilometer-length interferometer for gravitational waves detection located near Pisa. Its first science run, VSR1, occured from May to October 2007. The aims of the calibration are to measure the detector sensitivity and to reconstruct the time series of the gravitational wave strain h(t). The absolute length calibration is based on an original non-linear reconstruction of the differential arm length variations in free swinging Michelson configurations. It uses the laser wavelength as length standard. This method is used to calibrate the frequency dependent response of the Virgo mirror actuators and derive the detector in-loop response and sensitivity within ~5%. The principle of the strain reconstruction is highlighted and the h(t) systematic errors are estimated. A photon calibrator is used to check the sign of h(t). The reconstructed h(t) during VSR1 is valid from 10 Hz up to 10 kHz with systematic errors estimated to 6% in amplitude. The phase error is estimated to be 70 mrad below 1.9 kHz and 6 micro-seconds above
Joint searches for gravitational waves and high-energy neutrinos
No full textMany of the astrophysical sources and violent phenomena observed in our Universe are potential joint emitters of gravitational waves and high-energy cosmic radiation, in the form of photons, hadrons, and also neutrinos. This has triggered a collaborative analysis project between gravitational wave detectors and high-energy neutrino telescopes. In this article, we review some of the motivations for having pursuing science jointly and present the effort’s status
Open questions in astrophysically triggered gravitational wave searches
No full textSources of gravitational waves are often expected to also be observable through several other messengers, such as gamma rays, X-rays, optical, radio, and/or neutrino emission. Some of these channels are already being used in searches for gravitational waves with the LIGO-GEO600-Virgo interferometer network, and others are currently being incorporated into new searches. Astrophysical targets include gamma-ray bursts, soft-gamma repeaters, supernovae, and glitching pulsars. The simultaneous observation of electromagnetic or neutrino emission could be a crucial aspect for the first direct detection of gravitational waves. Information on the progenitor, such as trigger time, direction and expected frequency range, can enhance our ability to identify gravitational wave signatures with amplitudes close to the noise floor of the detector. Furthermore, combining gravitational waves with electromagnetic and neutrino observations will enable the extraction of scientific insight that was hidden from us before. The paper discusses the status of transient multimessenger detection efforts as well as intriguing questions that might be resolved in the future by advanced and third generation gravitational wave detector
Noise from scattered light in Virgo's second science run data
No full textVirgo is one of the large, ground-based interferometers aimed at detecting gravitational waves. One of the technical problems limiting its sensitivity is caused by light in the output beams which is backscattered by seismically excited surfaces and couples back into the main beam of the interferometer. The resulting noise was thoroughly studied, measured and mitigated before Virgo's second science run (VSR2). The residual noise during VSR2, which increases in periods with a large microseism activity, is accurately predicted by the theoretical model. The scattered light has been associated with transient events in the gravitational-wave signal of the interferometer
Status and perspectives of the Virgo gravitational wave detector
No full textInternational audienceVirgo is designed to detect gravitational waves of both astrophysical and cosmological origin in the frequency range from a few Hz to a few kHz. After the end of the first science run, partially overlapped with the LIGO fifth science run, the detector underwent several upgrades to improve its sensitivity. The second Virgo science run started at the beginning of July 2009 in coincidence with LIGO. A further upgrade is planned at beginning of 2010 with the installation of new suspensions for the test masses and of new mirrors. This will lead to a considerable improvement in the sensitivity and represents an intermediate step toward the development of the advanced detectors
Tools for noise characterization in Virgo
No full textInternational audienceSeveral software tools were used to perform on-line and of-line noise analysis as a support to commissioning activities, to monitor the rate of glitches, the occurrence of non stationary noise, the presence of environmental contamination, the behavior of narrow spectral features and the coherence with auxiliary channels. We report about the use of these tools to study the main sources of identified noise: broadband, spectral lines and glitches. Plans for the upgrade of the tools will be presented, for example for lines identification purpose to let the scientists in control room do noise characterization in an easier way
