JEEE-U (Journal of Electrical and Electronic Engineering-UMSIDA)
Not a member yet
122 research outputs found
Sort by
Design of Temperature and Humidity Control Systems in Quail Puppies Cages Using Fuzzy Logic Method: Perancangan Sistem Kendali Suhu dan Kelembaban pada Kandang Anakan Burung Puyuh Menggunakan Metode Logika Fuzzy
Full text linkoai:journal.umsida.ac.id:article/310After the quail eggs hatch, quail chicks need a warm place as a substitute for the mother to maintain body temperature. The temperature needed by quail chicks is approximately 37°C in the first week and each following week the temperature is lowered to room temperature of 28°C. This research applies the control of temperature and humidity of quail chicks based on fuzzy logic Tsukamoto method. As a detector of temperature and humidity on drums used DHT11 sensor. This temperature and room control system is designed to reduce mortality in quail chicks. The average temperature and humidity reading error for quail puppages by using the DHT 11 sensor is 1% of the temperature reading and 2% of the humidity reading. The results of the implementation of fuzzy logic control are able to maintain the stability of temperature and humidity in quail chicks cages at 32°C – 38°C with humidity between 40% RH – 70% RH
Electronic Sterilization of Tableware Using Ultraviolet Light Radiation: Sterilisasi Peralatan Makan Secara Elektronik Menggunakan Radiasi Sinar Ultraviolet
Full text linkThe hospital is one of the health service institutions that conducts complete individual health services that provide inpatient, outpatient and emergency services. Where in the hospital is also a gathering place for many people, namely the patient and also the patient's family. This is also a factor that bacteria and microorganisms can grow rapidly. As found on the patient's tableware. Because the tableware used continuously and alternately will make bacteria grow faster, especially if the process of washing the cutlery is less clean. From this problem emerged the idea to design a tool "Electronic sterilization of tableware using ultraviolet radiation". This tool utilizes ultraviolet radiation that has been studied and has been tested to inhibit bacterial growth. This design is made by finding references originating from journals, books and also articles which are then made a plan or description of the tool that aims to plan what kind of tool will be made, design in the form of hardware in the form of connections between input devices, processes and also outputs , while the software in the form of a program as a system driver. After the design is complete, the tool will be tested and analyzed. Based on the analysis conducted, there are several types of bacteria found in these tableware. After being irradiated with UV light for 15 minutes of exposure, it is found that the bacteria that were originally attached to the cutlery can die completely. This is evidenced by testing conducted in the microbiology laboratory with supervision by experts in their field
Automatic Pesticide Spray Based on Digital Image Processing in Chili Plants by Classification Backpropagation Neural Network Method: Penyemprot Pestisida Otomatis Berbasis Pengolahan Citra Digital pada Tanaman Cabai dengan Metode Klasifikasi
Full text linkIn Indonesia demand for chili still quite high and as if it has become a basic necessity for the community. Along with the world in the food processing industry, there has been an increase in the need for chillies, in addition to the high demand and the selling price of chilli peppers, it has encouraged the interest of the community to cultivate chili plants. However, biotic disorders that cause obstacles in efforts to increase chili production. On the leaves and fruit of the chili plant is a part of body the plant that allows the identification process of disease in the chili plant, because there will be changes in color and texture. The process of disease detection in chili plants through digital image processing using the feature extraction method, which has previously been done pre-processing. Then at the segmen-tation stage a thresholding operation is carried out to separate the healthy / diseased leaves / chili. For the classifi-cation of diseases using BPNN (Backpropagation Neural Network) method. The identification process will results five types of diseases, namely fusarium wilt, bacterial wilt, leaf foliage, curly leaves, and anthracnose. From this data will be sent by smartphone via IoT to the automatic sprayer to spray the type of pesticide in accordance with the dose and type of disease identified. Based on the results of testing using 150 samples of leaf and fruit images on chili plants obtained a success percentage of 43% in the leaves and 83.33% in the chilli fruit
Design of Wheeled Football Robot Coordination System at Base Station Using TCP / IP: Perancangan Sistem Koordinasi Robot Sepak Bola Beroda Pada Base Station Menggunakan TCP / IP
Full text linkWheel Soccer Division, Indonesian Robot Contest is an annual competition held by the Ministry of Education. One team in this division consists of 3 robots connected in wireless communication coordinated by base station. Besides that, base station computer also connects the robots with referee computer or called Refbox (Referee Box). Refbox as server for base station computer and base station computer as server for robots. The problem arises in base station has to play double roles, as server and client. In testing had two the results of communication from the referee box to basestation and basestation to the client so the data from the referee box can be accepted by the client with a success rate of 93%
Monitoring Battery Lighting and Public Street Light (PJU) With Telegram-Based Information System Microcontroller: Monitoring Pencahayaan Baterai dan Lampu Penerangan Jalan Umum (PJU) Dengan Sistem Informasi Telegram Berbasis Mikrokontroler
Full text linkThe development of automation technology has now been felt in all aspects of human life. The convenience and security offered in technology also has a positive impact, especially in the aspect of electrical energy. Public Street Lighting (PJU) is a means of street lighting provided by the Government to improve or optimize road equipment facilities in the form of street lighting tools in order to realize safety, security, order and smoothness of traffic as well as convenience for road users in traffic. Frequent blackouts and lack of supervision are inconveniences for public road users. monitoring technology for battery lighting and public street lighting (pju) with this microcontroller-based telegram information system is designed to make it easier to monitor and monitor if the lights go out at night or there is a problem with the battery that can be fixed immediately, the results can be seen by the sensor ( LUX) which is used as an automatic switch that can turn off the lights during the day and turn on the lights at night. And also equipped with an automatic sensor switch (PIR) which if the vehicle is not detected the automatic light will dim and vice versa, if detected with a distance of 8 meters the vehicle automatically lights up. Can inform technicians by telegram of damage to lights and batteries on the road. This is done to increase comfort, efficiency, transportation safety and also to develop technological systems to be more innovative
Turn To Turn Short Circuit Classification In Induction Motor Stator Windings Caused By Isolation Failure Using Neural Network (NN) Method: Klasifikasi Hubung Singkat Turn To Turn Pada Belitan Stator Motor Induksi Yang Disebabkan Kegagalan Isolasi Menggunakan Metode Neural Network (NN)
Full text linkAlmost all industries use induction motors as production aids, this is due to several reasons, namely, the resulting rotational speed is constant, the induction motor does not have a brush so that the friction loss can be reduced, and easy maintenance. In this study is to detect damage to the stator winding caused by lamination of the windings so that a short circuit occurs in one phase, which is also called a turn fault. The Fast Fourier Transform (FFT) method is used to detect currents with a load of 0%, and 100% which will later be detected for classification on the Neural Network (NN). Categorizing the level of loading and the level of damage experienced by induction motors, namely turn to turn u1, turn to turn u1 and v1, and turn to turn u1, v1 and w1. The reading of the test results conducted on the Neural Network has good prediction results because the Mean Squared Error (MSE) produced does not exceed the specified 5% erracy level
Algoritma Persaingan Imperialis Sebagai Optimasi Kontroler PID dan ANFIS Pada Mesin Sinkron Magnet Permanen : Imperialist Competitive Algorithm As PID Optimization and ANFIS Controller at Permanent Magnet Synchronous Machine
Full text linkPermanent Magnet Syschronous Machine (PMSM) has low torque, so good control is needed to be stable quickly. PMSM uses the principle of faraday experiments which is rotating a magnet in a coil or vice versa. When a magnet moves in a coil, there is a change in magnetic flux in the coil and penetrates perpendicular to the coil so that there is a potential difference between the ends of the coil, regarding this due to changes in magnetic flux. Magnetic flux can be changed by moving a magnet in a coil or vice versa by utilizing other energy sources. To get a good optimization result, the right control constants are needed. So that the best output is obtained. To get the right constants, a suitable and good method is needed, including using artificial intelligence. In this study using the Imperialist Competitive Algorithm (ICA) method. From the simulation results it was found that the best controller design in this study was ANFIS-ICA with the best profile, torque profile, voltage profile, and rotation profile. The largest current is 2.45 A, the smallest overshot torque is 0.48 pu, the largest voltage frequency is 9.84 khz, and the best rotation (close to the reference) is 700.02 rpm. The results of this study will be continued with the use of other artificial intelligence
Rancang Bangun Detektor Standart Preform Botol Minuman Menggunakan Metode Jaringan Saraf Tiruan: Design Of Standart Detector Standart Drink Bottle Using Artificial Neural Network Method
Full text linkPreform is a semi-finished material from a bottle before cooking in the blowing process. Standards form most, same shapes and colors in one production. However, it does not have to close in one production which requires several preforms that have different colors and weights than other preforms so that they are not included in the standard and must be rejected. In this case a standard detector and color of the preform drink bottle were made using backpropagation neural network method where hardware that loaded arduino uno, photodiode sensor, load cell and HX 711 module and LCD i2c 16 x 2. Photodiode sensors can be used in blue preform together with load cell which is translated directly preform which is directly converted by the HX711 module. Two input data is then processed in the Arduino UNO module. Data output from Arduino UNO is approved on the LCD and processed in the Artificial Neural Network in Matlab on the laptop. The final output of the research results will be displayed in the command window matlab column containing rich "YES" or "NO". In this study backpropagation artificial neural networks as a method to provide accurate assessment by displaying the test results with 19 grams, color density 8 with a voltage of 0.038 Volts and output data is 1 with error data -4.75E13
Real Time Clock Sebagai Tracking Sinar Matahari Pada Solar Cell Berbasis Mikrokontroler Untuk Lampu Taman: Real Watch Tracking As A Sun Ray On Microcontroller Based Solar Cells For Park Lights
Full text linkOne of the new and renewable energy is the utilization of sunlight into electricity. which can be used to be converted into electrical energy using solar panels. Installation of solar panels that are installed for garden lights so far are often still placed in a static position (silent) at an angle of 90⁰, while the sun moves from sunrise to sunset. Because it will cause maximum energy absorption in solar panels placed in a static position only at12:00. To overcome this problem a system is needed to track the position of the sun so that it is always perpendicular to the surface of the solar panel. Design and build Garden lights with a solar light tracking system on a microcontroller-based solar panel will later be made to move as it follows the direction of the sun's movement every hour, from sunrise to sunset. This tool will detect the time setting inputted by Real Time Clock (RTC) which is then processed by a microcontroller to drive a servo motor that functions as a solar panel drive machine so that the position of the solar panel will always be perpendicular to the sun throughout the day and the absorption of energy in the solar panel will more leverage. From the results of tests that have been done, the increase in the voltage of solar panels using a tracking system compared to solar panels without using a tracking system is 7.85%
Rancang Bangun Modul Pembelajaran Bengkel Listrik: Designing Electric Workshop Learning Modules
Full text linkElectric motor is an electric machine that has a function as a converter of electrical energy into mechanical energy. Electric motors are widely used as movers because they are better in terms of technical and economical, but have disadvantages such as large initial currents so that they cannot last long, to overcome this can be used Y-utan star starting method both manually and automatically created in a panel box. In the operation and manufacture of a protection system for a 3 phase induction motor, some supporting equipment can be arranged in a panel box so that motor performance can be maximized. The results of this tool design are in the form of a panel box in which there are three types of circuits, namely: 3 phase induction motor operation circuit with the starting Y-∆ automatically, reversing the direction of 3 phase induction motor rotation, and 3 phase induction motor operation in two places. Where the series is equipped with a protection system and can be operated manually and automatically