Osmaniye Korkut Ata University Academic Repository
Not a member yet
    5726 research outputs found

    Investigation of the behavior of highway foundation ground reinforced with palm, geotextile and bituminous palm under repeated loads

    Get PDF
    Bu çalışmanın amacı, karayolu zemin tabakasının farklı malzemeler kullanılarak tekrarlı yükler altında davranışının incelenmesi, karşılaştırılması ve değerlendirilmesidir. Palmiye, geotekstil ve bitümlü palmiye kullanılarak güçlendirilen karayolu zemininin referans değerleriyle karşılaştırılması yapılmıştır. Çalışmanın sonuçları toplam deformasyon, kalıcı deformasyon, elastik deformasyon, Trafik Fayda Oranı (TBR), Tekerlek İzi Azalma Oranı (RDR) ve elastik deformasyon yüzdesi bakımından değerlendirilmiştir. 23 mm kalıcı deformasyon değerinde TBR değerleri geotekstil ile güçlendirilmiş zeminde 2,96, palmiye ile güçlendirilmiş zeminde 5,85 ve bitümlü palmiye ile güçlendirilmiş olan zeminde 1,73 olarak bulunmuştur. 2000 yük çevrimi sonunda geotekstil, palmiye ve bitümlü palmiye ile güçlendirilmiş zeminler için RDR değerleri sırasıyla %32,97, %45,8 ve %24,3'tür.This study aimed to investigate, compare, and evaluate the behavior of the highway base layer under repeated loads using different materials. The base layer reinforced with palm, geotextile, and bituminous palm, was compared with reference values. The analysis of the experimental results was evaluated based on total, permanent, and elastic deformation, Traffic Benefit Ratio (TBR), Ruth Depth Reduction (RDR), and elastic deformation percentage. At 23 mm permanent deformation value, TBR values are 2.96 for geotextile reinforcement, 5.85 for palm reinforcement, and 1.73 for bituminous palm reinforcement. At the end of 2000 load cycles, RDR values for geotextile, palm, and bituminous palm reinforcement were 32.97%, 45.8%, and 24.3%, respectively

    Farklı Bacillus ve Trichoderma türleriyle domateste bakteriyel leke (Xanthomonas euvesicatoria) ve bakteriyel solgunluk (Clavibacter michiganensis subsp. michiganensis) hastalıklarının biyolojik mücadelesi

    No full text
    Bitki hastalıklarıyla mücadelede, dost mikroorganizmalar adeta doğanın kendi koruyucuları gibi görev yapmaktadır. Bu minik mucizelerin sahip olduğu etkileyici mekanizmaları sayesinde bitkileri hastalıklardan korurken aynı zamanda doğal dengenin korunmasına ve sürdürülebilir tarımsal uygulamalara katkı sağlamaktadırlar. Çevre dostu özellikleri ve yüksek etkinlikleri nedeniyle biyolojik mücadele elemanlarının bitki hastalıklarının yönetiminde yer alması kimyasal mücadeleye alternatif bir strateji haline gelmekte ve giderek daha fazla ilgi görmektedir. Bu amaç doğrultusunda, Xanthomonas euvesicatoria’nın neden olduğu Bakteriyel Leke ve Clavibacter michiganensis subsp. michiganensis’nın neden olduğu Bakteriyel Solgunluk hastalıklarının biyolojik mücadelesinde farklı Bacillus (Bacillus amyloliquefaciens, Bacillus pumilus, Bacillus Subtilis, Bacillus licheniformis, Bacillus megaterium) ve Trichoderma (Trichoderma harzianum, Trichoderma konigii) türlerini içeren ticari bir ürünün bu hastalıkları baskılayıcı etkisi araştırılmıştır. Mikrobiyal gübre ruhsatlı bu ürün Bakteriyel Solgunluk hastalığını istenilen düzeyde azaltamazken Bakteriyel Leke hastalığını %51 oranında oldukça başarılı bir şekilde engellemiştir. Sonuç olarak bu çalışma, çeşitli antagonistleri içeren ürünlerin, verim arttırıcı özelliklerinin yanı sıra hastalıkları baskılama amacıyla da kullanıldığını bir kez daha vurgulamaktadır

    Sequential Electrochemical and Chemical Multi-Polymerization of Catechol for Abatement of Environmental Pollutants

    No full text
    Catechol is a substance that is commonly found in wastewaters from a variety of sectors including paper, paint, petroleum, dyes, antioxidants, pesticides, iron and steel, solvents, nylon, detergent, textile, plastic, rubber, cosmetics, and medicine. In this study, sequential electrochemical and chemical multi-polymerization of catechol was investigated for environmental pollution abatement. The effect of operating parameters like catechol concentration (2-10 g/L), ammonium persulphate (APS) concentration (2-10 g/L) and reaction temperature (20-60 degrees C) were evaluated using response surface methodology. Catechol concentration was determined using HPLC in a gradient mobile phase. The electrochemical behavior of the polymer was investigated by cyclic voltammetry (CV). The structural and morphological properties of polycatechol were characterized by Fourier transform infrared spectroscopy (FTIR), and scanning electron microscopy with energy dispersive X-ray (SEM-EDX) analysis. It was observed from the SEM images a polymeric structure developed from a crystalline and heterogeneous structure when the APS concentration increased. Similarly, it was seen in SEM images that the polymers transitioned from a bulk and heterogeneous structure to a homogeneous structure as the temperature increased, and back to a heterogeneous structure as the catechol concentration increased. It was also found that catechol removal increased and reaction selectivity decreased by increasing the reaction temperature. The optimum operating conditions were found as 4 g/L catechol concentration, 9.5 g/L APS concentration, 30 degrees C reaction temperature with 100 cycles at 50 mV/s of electrochemical polymerization and 72 h of chemical polymerization. The results of this study show the potential of challenging new routes not only facile polymerization of organic monomers but also to decrease the undesirable pollutant concentration in the wastewater.Scientific and Technological Research Council of Turkiye (TUBIdot;TAK); Mersin University Scientific Research Projects Center (MEUE BAP) [2015-TP2-1039]Open access funding provided by the Scientific and Technological Research Council of Turkiye (TUB & Idot;TAK). This study was supported by Mersin University Scientific Research Projects Center (MEUE BAP) with Grant No. 2015-TP2-1039

    Some biological activities and element levels of Lycoperdon pratense

    No full text
    Mushrooms are natural products with many biological activities. In this study, antioxidant, antimicrobial, anticholinesterase activities and element levels of Lycoperdon pratense Pers. were determined. In this context, the mushroom was extracted with ethanol in a soxhlet device. Antioxidant potential was determined using Rel assay kits. Antimicrobial activity was determined using the agar dilution method. Antialzheimer activity was determined by acetyl- (AChE) and butyrylcholinesterase (BChE) potentials. The levels of elements accumulated in the mushroom were scanned using the wet digestion method. As a result of the analysis, the TAS value of the mushroom was measured as 2.589 +/- 0.118 mmol Trolox equiv./L, the TOS value was 10.360 +/- 0.197 mu mol H2O2 equiv./L and the OSI value was 0.401 +/- 0.013. The mushroom extract was found to have high activity against bacteria. It was determined that the extract had an effect against microorganisms at concentrations between 50-400 mu g/mL. It was determined that the anti-AChE IC50 value of the mushroom extract was 14.48 +/- 0.80 mu g/mL and the anti-BChE IC50 value was 23.10 +/- 1.21 mu g/mL. It is also thought that it can be used as an indicator in terms of element levels within the mushroom. As a result, it was determined that the mushroom has antioxidant, antimicrobial and antiallergic potential

    Emulsion electrospinning of zein nanofibers with carotenoid microemulsion: Optimization, characterization and fortification

    No full text
    In this study, carotenoid microemulsion was encapsulated in zein nanofibers via emulsion electrospinning. Optimization study was applied to determine optimum parameters by response surface methodology. The voltage, flow rate and distance as optimum conditions were determined as 23 kV, 1.7 mL/h and 12.75 cm, respectively. Lycopene, & beta;-carotene, encapsulation efficiency, encapsulation yield and zeta potential of zein nanofibers in optimum conditions were estimated as 4.054 mg/kg, 0.649 mg/kg, 77.78%, 41.76% and-29.73 mV, respectively. The addition of microemulsion affected nanofibers diameter and morphologies. Diffusion co-efficient of zein nanofibers decreased with addition of microemulsion under optimum conditions. The electro-spinning improved thermal stability of microemulsion. The carotenoid microemulsion could be entrapped into the zein fibers according to ATR-FTIR spectrum. Model foods were fortificated with zein nanofibers. The addition of nanofibers changed color of the foods during the storage. Carotenoid compounds were more stable in nanofibers followed by olive oil, milk and water.Technological Research Council of Turkey (TUBITAK) [119O108, FBA- 2018-9780]The authors acknowledge Technological Research Council of Turkey (TUBITAK) (Project no: 119O108) for financial support of this study. The authors thank to Cukurova University, Turkey (Project no: FBA- 2018-9780) for financial supports

    Lisansüstü Tezlerde Ziya Gökalp (Bibliyometrik Bir Deneme)

    No full text
    The writings, studies and theses about the writer and scientist, whose real name is Mehmet Ziya Gökalp (1876-1924) and known as the founder of sociology in Turkey, are much more than the subject of an article. For this reason, this study is limited to postgraduate studies at the National Thesis Center of the Council of Higher Education. The study is important in terms of revealing under which headings Ziya Gökalp is studied in universities, which are centers of science. The method followed in the research was scanning and document review in the thesis center. Six of the 92 theses reached as a result of the scans were eliminated because they were not directly related to Ziya Gökalp. Eleven of the remaining 86 theses are doctoral theses, while seventy-five are master's theses. The theses are first tabulated as the thesis number, date, person who wrote the thesis, thesis title, type of the thesis, university where the thesis was made, institute and department where the thesis was presented. A chronological order was made in the preparation of the tables. The study aims to reveal how much the subject of Ziya Gökalp is addressed in graduate theses. Based on this, this study also serves as a guide for those who are considering researching the subject in the future. Due to the large number of theses, theses were not subjected to content analysis.Asıl adı Mehmet Ziya Gökalp (1876-1924) olan ve Türkiye’de sosyolojinin kurucusu olarak bilinen yazar ve bilim adamının hakkında yazılanlar, yapılan çalışmalar, tezler bir makalenin konusu olmaktan çok daha fazladır. Bu nedenle bu çalışma Yükseköğretim Kurulu Ulusal Tez Merkezi’nde bulunan lisansüstü çalışmalarla sınırlandırılmıştır. Çalışma Ziya Gökalp’in bilim yuvası olan üniversitelerde hangi başlıklar altında incelendiğini ortaya koyması açısından önemlidir. Araştırmada izlenen yol tez merkezinde tarama ve doküman inceleme şeklinde olmuştur. Taramalar sonucunda ulaşılan 92 tezden altı tanesi direkt Ziya Gökalp ile ilgili olmadığı için elenmiştir. Geriye kalan 86 tezden 11’i doktora seviyesinde hazırlanmış tezler iken 75’i de yüksek lisans seviyesinde hazırlanmış tezlerdir. Tezler öncelikle tez numarası, tarih, tezi yazan kişi, tez başlığı, tezin türü, tezin yapıldığı üniversite, tezin sunulduğu enstitü ve anabilim dalı şeklinde tablolaştırılmıştır. Tabloların hazırlanmasında kronolojik bir sıralama yapılmıştır. Çalışmanın amacı Ziya Gökalp konusunun lisansüstü tezlerde ne kadar ele alındığını ortaya konmasıdır. Buradan hareketle bu çalışma bundan sonra konuyla ilgili çalışma yapmayı düşünenler için de yol gösterici bir özellik taşımaktadır. Tez sayısının fazla olmasından dolayı tezler içerik analizine tabi tutulmamıştır

    Inconel 718 Malzemenin Borlanmasında İşlem Parametrelerinin Kaplama ve Aşınma Özelliklerine Etkisinin Makine Öğrenmesi Yöntemleri Kullanılarak Araştırılması

    No full text
    Borlama, nikel esaslı süper alaşımların yüzey ve aşınma özelliklerini iyileştiren etkili bir işlemdir. Ancak, bu işlemin optimize edilmesi ve kaplama kalitesinin arttırılması için detaylı bir anlayışın gerekliliği ortaya çıkmaktadır. Çalışmanın temel amacı, borlama işlem parametrelerinin optimize edilmesi ve kaplama kalitesinin arttırılması için makine öğrenmesi kullanımını ortaya koymaktır. Çalışma kapsamında, kaplama kalınlığı, yüzey pürüzlülüğü, mikrosertlik gibi özellikler yanında 25, 400 ve 750 °C sıcaklık şartlarındaki ortalama sürtünme katsayısı ve aşınma hacim kaybının borlama sıcaklığı ve süresine bağlı değişimi incelenmiştir. Çalışmada öncelikle her bağımlı değişken için en uygun makine öğrenmesi algoritması belirlenmiş ve bu algoritmalar kullanılarak oluşturulan üç boyutlu yüzey grafikleri yardımıyla bağımlı değişkenlerin borlama sıcaklığı ve süresi ile değişimi görselleştirilmiştir. Grafikler üzerinde yapılan incelemeler sonucunda işlem sıcaklığı ve süresinin artmasıyla kaplama kalınlığı ve sertliğiyle birlikte yüzey pürüzlülüğünün de arttığı görülmüştür. Oda sıcaklığında ve 750 C’de yapılan aşınma deneylerinde sürtünme katsayısının en düşük değerinin (0,26) 1000-1050 °C arasında 5-6 saat aralığındaki işlem süresinde 0,26 elde edileceği saptanmıştır. Aşınma testlerinin 400 °C’de yapılması durumunda ise en düşük sürtünme katsayısının 900-1000 °C sıcaklık ve 3-5 saat işlem süresi aralığında (0,31) olacağı tespit edilmiştir. Ek olarak borlama sıcaklığın aşınma hacim kaybı üzerindeki etkisinin borlama işlem süresinden daha fazla olduğu tespit edilmiştir

    Decontamination of Escherichia coli biofilms on spinach by thermosonication and organic acid treatment

    No full text
    Bu çalışmada, ıspanakta gelişen Escherichia coli biyofilmleri üzerine ultrasonikasyon ve organik asit muamelesinin etkisi araştırılmıştır. E. coli biyofilmi oluşturulan ıspanak yapraklarının dekontaminasyonu için farklı çözelti (PBS, laktik asit ve asetik asit), sıcaklık (20, 40 ve 50oC) ve sürelerdeki (2 ve 5 dakika) sonikasyon işlemine başvurulmuştur. Ispanakta gelişen E. coli biyofilm inaktivasyonu üzerine sıcaklık, süre ve inaktivasyon çözeltisinin etkisi istatistiksel olarak önemli (p<0.05) bulunmuştur. Farklı koşullardaki sonikasyon işlemi ile ıspanaktaki E. coli biyofilmi canlı hücre sayısında 1.02 ve 6.03 log kob/cm2 arasında azalış meydana gelmiştir. Ispanakta en yüksek E. coli biyofilm inaktivasyonu 50oC'de 5 dakika sonikasyon koşullarında laktik asit muamelesi ile sağlanırken en düşük biyofilm inaktivasyonu 20oC'de 2 dakika sonikasyon koşullarında PBS muamelesi ile sağlanmıştır. Standartlaştırılmış regresyon katsayılarına göre, bağımsız değişkenlerin biyofilm inaktivasyon oranı üzerindeki göreli önem sırası, sıcaklık, çözelti ve süre olarak belirtilmiştir. Ispanağa uygulanan dekontaminasyon işlemlerinin duyusal özellikler üzerinde genellikle olumsuz bir etkisinin olmadığı ancak yüksek sıcaklıkta asetik asit ile muamele edilen örneklerde duyusal beğenilerin belirgin biçimde azaldığı tespit edilmiştir. Sonuç olarak, ıspanak gibi taze yapraklı sebzelerde etkili bir dekontaminasyon için laktik asit ve termosonikasyon muamelesi önerilmiştir.In this study, the effects of ultrasonication and organic acid treatment on Escherichia coli biofilms on spinach were investigated. Sonication process at different solution (PBS, lactic acid and acetic acid), temperature (20, 40 and 50oC) and time (2 and 5 minutes) was used for decontamination of spinach leaves with E. coli biofilm. The effects of temperature, time and inactivation solution on the inactivation of E. coli biofilm on spinach were found to be statistically significant (p<0.05). With the sonication process under different conditions, reduction in viable cell counts of E. coli biofilm on spinach was changed between 1.02 and 6.03 log cfu/cm2. The highest E. coli biofilm inactivation in spinach was achieved by lactic acid treatment under sonication conditions at 50oC for 5 minutes, while the lowest biofilm inactivation was achieved by PBS treatment under sonication conditions at 20oC for 2 minutes. According to standardized regression coefficients, the order of relative importance of the independent variables on the biofilm inactivation rate was indicated as temperature, solution, and time. It has been determined that decontamination processes applied to spinach generally do not have a negative effect on sensory properties, but sensory properties are significantly reduced in samples treated with acetic acid at high temperatures. As a result, lactic acid and thermosonication treatment have been suggested for effective decontamination of fresh leafy vegetables such as spinach

    Intermediating effect of mineral resources on renewable energy amidst globalization, financial development, and technological progress: Evidence from globe based on income-groups

    No full text
    All parties have taken a much closer look at the critical impact of renewable energy (RE) consumption in reducing climate -related anthropogenic problems. Although mineral resources play an important role in stimulating RE due to their use in the installation of RE capacity, the role of mineral resources has not received more attention. In view of this, the study examines the intermediating role of mineral resource (MR) use on RE for 119 countries from 1996 to 2019 using globalization (GI), financial development (FD), technological progress (TI), industrial structure upgrade (IS), and applying the ARDL approach. The outcomes indicate that (i) FD has a negative effect on RE in high -income countries, while mineral extraction and technological progress promote RE; (ii) in middle -income countries, FD promotes RE, while GI and MR constrain the development of RE; (iii) the interaction between MR and FD is negative, suggesting that MR may limit the positive effect of financialization on RE. Thus, the outcomes highlight that MR and FD have a global effect on RE. Therefore, policymakers should consider MR and FD as important factors in supporting the transition to clean energy.National Natural Science Foundation of China [72104246, 71874203]This work is supported by the National Natural Science Foundation of China (Grant No. 72104246, 71874203)

    Solucan ve biyo-gübre uygulamalarının çilek bitkisinin kök ve gövdesinin besin elementi içeriğine etkisi

    No full text
    Çilek, besin değeri açısından önemi ve ekonomik faydası nedeniyle Türkiye'de üretimi her geçen yıl artan meyvelerden birisidir. Son yıllarda organik çileğe olan talep de artmaktadır. Organik çilek yetiştiriciliğinde yüksek verim ve kaliteyi elde etmek için bitkinin ihtiyacı olan besin elementlerinin belirlenmesi ve uygun yöntemlerle verilmesi gerekmektedir. Bu çalışmada Monterey çilek çeşidinde solucan gübresinin tek başına ve faydalı bakteri ve mikoriza içeren biyo-gübreler ile birlikte uygulamalarının çilek bitkisinin kök ve gövdesinde azot (N), fosfor (P), potasyum (K), kalsiyum (Ca), magnezyum (Mg), demir (Fe), çinko (Zn) ve mangan (Mn) içeriğine etkileri incelenmiştir. Akdeniz iklimi etkisi altında Osmaniye ilinde yürütülen bu tarla denemesinde sadece su verilen kontrol uygulamasının yanında solucan gübresi ve birlikte uygulamaların yer aldığı 7 farklı uygulama yer almıştır. Solucan gübresi ve biyo-gübrelerin birlikte uygulamasında kök ve gövdenin besin elementi içeriği, tek başına uygulanan solucan gübresi ve kontrole kıyasla daha yüksek olmuştur. Solucan gübresi ile içeriğinde Bacillus amyloliquefaciens, Bacillus pumilus, Bacillus subtilis, Bacillus licheniformis, Bacillus megaterium, Trichoderma harzianum, Trichoderma konigii olan biyo-gübrenin birlikte uygulamasının, diğer uygulamalara göre daha yüksek kök N (%1.04), K (%0.51), Mn (25.38 mg kg−1), Zn (64.88 mg kg−1) ve gövde N (%1.71), P (%0.17), K (%1.29), Mg (%0.22), Fe (159.13 mg kg−1) içeriklerine sahip olduğu belirlenmiştir. Bu bulgular, solucan gübresi ve biyo-gübrenin birlikte uygulanmasının diğer uygulamalara kıyasla kök ve gövdenin bitki besin içeriğine daha fazla katkı sağladığını göstermektedir

    598

    full texts

    5,726

    metadata records
    Updated in last 30 days.
    Osmaniye Korkut Ata University Academic Repository
    Access Repository Dashboard
    Do you manage Open Research Online? Become a CORE Member to access insider analytics, issue reports and manage access to outputs from your repository in the CORE Repository Dashboard! 👇