1,720,964 research outputs found
Going Beyond Counting First Authors in Author Co-citation Analysis
Get PDFThe present study examines one of the fundamental aspects of author co-citation analysis (ACA) - the way co-citation
counts are defined. Co-citation counting provides the data on which all subsequent statistical analyses and mappings
are based, and we compare ACA results based on two different types of co-citation counting - the traditional type that
only counts the first one among a cited work's authors on the one hand and a non-traditional type that takes into
account the first 5 authors of a cited work on the other hand. Results indicate that the picture produced through this non-traditional author co-citation counting contains more coherent author groups and is therefore considerably clearer. However, this picture represents fewer specialties in the research field being studied than that produced through the traditional first-author co-citation counting when the same number of top-ranked authors is selected and analyzed. Reasons for these effects are discussed
Variations on the Author
Get PDF“Variations on the Author” discusses two of Eduardo Coutinho’s recent films (Um Dia na Vida, from 2010, and Últimas Conversas, posthumously released in 2015) and their contribution to the general question of documentary authorship. The director’s filmography is characterized by a consistent yet self-effacing form of authorial self-inscription: Coutinho often features as an interviewer that rather than express opinions propels discourses; an interviewer that is good at listening. This mode of self-inscription characterizes him as an author who is not expressive but who is nonetheless markedly present on the screen. In Um Dia na Vida, however, Coutinho is completely absent form the image, while Últimas Conversas, on the contrary, includes a confessional prologue that moves the director from the margins to the center of his films. This article examines the ways in which these works stand out in the filmography of a director who offers new insights into the notion of cinematic authorship
Appropriate Similarity Measures for Author Cocitation Analysis
Get PDFWe provide a number of new insights into the methodological discussion about author cocitation analysis. We first argue that the use of the Pearson correlation for measuring the similarity between authors’ cocitation profiles is not very satisfactory. We then discuss what kind of similarity measures may be used as an alternative to the Pearson correlation. We consider three similarity measures in particular. One is the well-known cosine. The other two similarity measures have not been used before in the bibliometric literature. Finally, we show by means of an example that our findings have a high practical relevance.information science;Pearson correlation;cosine;similarity measure;author cocitation analysis
Dispelling the Myths Behind First-author Citation Counts
Get PDFWe conducted a full-scale evaluative citation analysis study of scholars in the XML research field to explore just how different from each other author rankings resulting from different citation counting methods actually are, and to demonstrate the capability of emerging data and tools on the Web in supporting more realistic citation counting methods. Our results contest some common arguments for the continued
use of first-author citation counts in the evaluation of scholars, such as high correlations between author rankings by first-author citation counts and other citation
counting methods, and high costs of using more realistic citation counting methods that are not well-supported by the ISI databases. It is argued that increasingly available digital full text research papers make it possible for citation analysis studies to go beyond what the ISI databases have directly supported and to employ more
sophisticated methods
Study of the long term behavior of glued-in rod connections in variable climate conditions
No full textLa technique des goujons collés dans les structures bois allie performances mécaniques et esthétisme. Elle répond au besoin de conservation du bâti pour le domaine de la rénovation et au besoin d’assemblages de plus en plus rigides et résistants en construction neuve avec l’avènement des structures bois de grandes ampleurs et l’arrivée de nouveaux produits tels que le bois lamellé croisé (CLT). De nombreuses études de caractérisation mécanique ont été menées au cours de ces 35 dernières années. L’enquête menée auprès des professionnels et experts en vue de l’introduction de cette technique dans l’Eurocode 5 a néanmoins révélé des attentes et lacunes particulières vis-à-vis des connaissances sur le comportement des assemblages multi-tiges, le choix des adhésifs, le comportement à long terme du collage et les techniques de contrôle qualité. Les travaux de cette thèse, menés en collaboration entre l’université de Bordeaux et l’Université Laval (Québec, Canada), ont pour objectif d’apporter des réponses sur le comportement mécanique des adhésifs, et assemblages sous sollicitation thermique et d’initier les développements sur le comportement à long terme et les assemblages multi-tiges. Les principaux résultats sont issus de travaux expérimentaux et numériques valorisés sous la forme d’articles scientifiques. Les essais mécaniques dynamiques menés sur une colle polyuréthane (PUR) et une résine époxy (EPX) entre 30°C et 120°C mettent en avant des différences importantes de raideur et de dégradations entre les deux adhésifs. Exposés à la chaleur, les assemblages sont eux aussi affectés avec des pertes de raideur et de résistance dès 40°C, en amont de la température de transition vitreuse et de la dégradation des adhésifs. Amené à suivre le régime de température extérieur, l’assemblage doit par sa conception être isolé afin de prévenir les risques aux états limites de service (ELS) et aux états limites ultimes (ELU). Très peu de données sont disponibles dans la littérature sur le comportement à long terme des assemblages goujons collés. L’étude du fluage ajoute une dimension temporelle aux problématiques de raideur. La base de données expérimentales collectée dans ces travaux repose sur 12 campagnes d’essais de 1 à 2 mois en conditions climatiques régulées en température et humidité relative, ou variables (service classe 1). Chargement et climat influent sur le glissement, mais aussi sur la durée de vie. Si des disparités sont présentes entre EPX et PUR, les études menées à 20°C et 50°C révèlent à nouveau l’importance de prendre en considération la température, notamment aux ELS. L’étude en régime variable illustre de son côté la sensibilité du système aux variations de température et d’humidité. L’étude de la répartition des efforts en fonction de la raideur des goujons est choisie comme fil conducteur pour investiguer le passage vers des éléments multi-tiges. Un modèle 3D mono-tige aux éléments finis est tout d’abord développé pour prendre en compte l’orthotropie du bois et regarder l’influence du centre de moelle jusqu’à présent négligée. Par la suite ce modèle est étendu aux configurations multi-tiges afin de simuler différentes configurations d’essais. Un prototype d’essai de caractérisation mécanique des assemblages multi-tiges est finalement présenté.Glued-in rods have successfully been used for connections or reinforcement of timber structures. With the development of tall and large timber buildings and new products such as Cross Laminated Timber (CLT), there is an increasing need for connections that provide high stiffness and strength. Timber connections using glued in rods have a general aesthetic appeal, and take advantage of the structural adhesives that provide a high stiffness and load capacity. During the last 30 years, multiple applications have been developed for renovation and new construction. In parallel, numerous investigations have characterized the mechanical performance of these connections, but harmonized design rules are not available. A lack of knowledge on the multiple-rod connections, on the choice of adhesives, on long-term effects and on the control of quality is identified by a recent study and must be investigated before a new submission to Eurocode 5. This thesis is performed in the framework of collaboration between Université de Bordeaux (France) and Université Laval (Canada). Objectives are focused on the mechanical performance of adhesives and glued-in rod connections under elevated temperature, on the development of creep tests and the investigations of multiple-rod connections. This study combines experimental and finite element modelling results, which are presented in the form of scientific articles. A Dynamic Mechanical Analysis (DMA) on one polyurethane (PUR) and one epoxy (EPX) adhesives followed by static tensile tests on the connections with small-diameter steel glued-in rods have been conducted at different temperatures. High differences in stiffness are observed between the two adhesives. Glued-in rod connections with the EPX and PUR adhesives demonstrate significant losses of stiffness and resistance beyond 40°C, before the glass transition temperature of the adhesive. Following the outside temperature, connections must be insulated to prevent excessive slip and risk of failure at the Serviceability Limits State (SLS) and at the Ultimate Limit States (ULS). Few data on the long-term effects are available in the literature. In this work, 12 campaigns of creep tests, adding time effects to previous work, have been performed. Glued-in rod connections were tested during one to two months in a conditioning room where temperature and relative humidity were controlled or in a room with a variable climate representative of service class 1. Disparities were observed between EXP and PUR. Creep tests conducted at 20°C and 50°C revealed an important role of the temperature, particularly for SLS. Creep tests in variable climate illustrated the sensibility of connections to the temperature and humidity variations. The stiffness and stress distribution in multiple-rod connections were investigated. First, a 3D model was developed to observe the influence of the wood orthotropy on the stiffness and stress distribution in a connection with a single rod. Then, the model was extended to multiple-rod connections to simulate different loads and boundary conditions. Finally, a prototype of a connection with multiple glued-in rods was tested
La Grave : prospective sur un site unique
No full textProspective study of a township populated by five hamlets and a main village, located in France’s Hautes-Alpes. La Grave is based at the feet of a mountain that has always dictated the local way of life: La Meije.Étude prospective portant sur une commune formée de cinq hameaux et d’un village dans les Hautes-Alpes françaises. La Grave se trouve aux pieds d’une montagne qui dicte les conditions de vie locale depuis toujours : La Meije
koamabayili/VECTRON-author-checklist: VECTRON author checklist
No full textWe have done our best to complete the author checklist relating to the use of animals in the hut study. Note that the objective for the hut study was to evaluate the IRS treatment applications for residual efficacy against Anopheles mosquitoes, including the local An. coluzzii mosquito population. Cows were only used to attract mosquitoes into the huts and no tests were carried out directly on the cows. The author checklist is intended for use with studies where experiments are carried out on animals, which is why we have had such difficulty in completing this for the hut study, as many of the questions do not relate to how the cows were used
Study of the long term behavior of glued-in rod connections in variable climate conditions
No full textLa technique des goujons collés dans les structures bois allie performances mécaniques et esthétisme. Elle répond au besoin de conservation du bâti pour le domaine de la rénovation et au besoin d’assemblages de plus en plus rigides et résistants en construction neuve avec l’avènement des structures bois de grandes ampleurs et l’arrivée de nouveaux produits tels que le bois lamellé croisé (CLT). De nombreuses études de caractérisation mécanique ont été menées au cours de ces 35 dernières années. L’enquête menée auprès des professionnels et experts en vue de l’introduction de cette technique dans l’Eurocode 5 a néanmoins révélé des attentes et lacunes particulières vis-à-vis des connaissances sur le comportement des assemblages multi-tiges, le choix des adhésifs, le comportement à long terme du collage et les techniques de contrôle qualité. Les travaux de cette thèse, menés en collaboration entre l’université de Bordeaux et l’Université Laval (Québec, Canada), ont pour objectif d’apporter des réponses sur le comportement mécanique des adhésifs, et assemblages sous sollicitation thermique et d’initier les développements sur le comportement à long terme et les assemblages multi-tiges. Les principaux résultats sont issus de travaux expérimentaux et numériques valorisés sous la forme d’articles scientifiques. Les essais mécaniques dynamiques menés sur une colle polyuréthane (PUR) et une résine époxy (EPX) entre 30°C et 120°C mettent en avant des différences importantes de raideur et de dégradations entre les deux adhésifs. Exposés à la chaleur, les assemblages sont eux aussi affectés avec des pertes de raideur et de résistance dès 40°C, en amont de la température de transition vitreuse et de la dégradation des adhésifs. Amené à suivre le régime de température extérieur, l’assemblage doit par sa conception être isolé afin de prévenir les risques aux états limites de service (ELS) et aux états limites ultimes (ELU). Très peu de données sont disponibles dans la littérature sur le comportement à long terme des assemblages goujons collés. L’étude du fluage ajoute une dimension temporelle aux problématiques de raideur. La base de données expérimentales collectée dans ces travaux repose sur 12 campagnes d’essais de 1 à 2 mois en conditions climatiques régulées en température et humidité relative, ou variables (service classe 1). Chargement et climat influent sur le glissement, mais aussi sur la durée de vie. Si des disparités sont présentes entre EPX et PUR, les études menées à 20°C et 50°C révèlent à nouveau l’importance de prendre en considération la température, notamment aux ELS. L’étude en régime variable illustre de son côté la sensibilité du système aux variations de température et d’humidité. L’étude de la répartition des efforts en fonction de la raideur des goujons est choisie comme fil conducteur pour investiguer le passage vers des éléments multi-tiges. Un modèle 3D mono-tige aux éléments finis est tout d’abord développé pour prendre en compte l’orthotropie du bois et regarder l’influence du centre de moelle jusqu’à présent négligée. Par la suite ce modèle est étendu aux configurations multi-tiges afin de simuler différentes configurations d’essais. Un prototype d’essai de caractérisation mécanique des assemblages multi-tiges est finalement présenté.Glued-in rods have successfully been used for connections or reinforcement of timber structures. With the development of tall and large timber buildings and new products such as Cross Laminated Timber (CLT), there is an increasing need for connections that provide high stiffness and strength. Timber connections using glued in rods have a general aesthetic appeal, and take advantage of the structural adhesives that provide a high stiffness and load capacity. During the last 30 years, multiple applications have been developed for renovation and new construction. In parallel, numerous investigations have characterized the mechanical performance of these connections, but harmonized design rules are not available. A lack of knowledge on the multiple-rod connections, on the choice of adhesives, on long-term effects and on the control of quality is identified by a recent study and must be investigated before a new submission to Eurocode 5. This thesis is performed in the framework of collaboration between Université de Bordeaux (France) and Université Laval (Canada). Objectives are focused on the mechanical performance of adhesives and glued-in rod connections under elevated temperature, on the development of creep tests and the investigations of multiple-rod connections. This study combines experimental and finite element modelling results, which are presented in the form of scientific articles. A Dynamic Mechanical Analysis (DMA) on one polyurethane (PUR) and one epoxy (EPX) adhesives followed by static tensile tests on the connections with small-diameter steel glued-in rods have been conducted at different temperatures. High differences in stiffness are observed between the two adhesives. Glued-in rod connections with the EPX and PUR adhesives demonstrate significant losses of stiffness and resistance beyond 40°C, before the glass transition temperature of the adhesive. Following the outside temperature, connections must be insulated to prevent excessive slip and risk of failure at the Serviceability Limits State (SLS) and at the Ultimate Limit States (ULS). Few data on the long-term effects are available in the literature. In this work, 12 campaigns of creep tests, adding time effects to previous work, have been performed. Glued-in rod connections were tested during one to two months in a conditioning room where temperature and relative humidity were controlled or in a room with a variable climate representative of service class 1. Disparities were observed between EXP and PUR. Creep tests conducted at 20°C and 50°C revealed an important role of the temperature, particularly for SLS. Creep tests in variable climate illustrated the sensibility of connections to the temperature and humidity variations. The stiffness and stress distribution in multiple-rod connections were investigated. First, a 3D model was developed to observe the influence of the wood orthotropy on the stiffness and stress distribution in a connection with a single rod. Then, the model was extended to multiple-rod connections to simulate different loads and boundary conditions. Finally, a prototype of a connection with multiple glued-in rods was tested
- …
