1,720,965 research outputs found
An inductive gap measurement method for square butt joints
No full textA recent method in aero engine production is to fabricate components from smaller pieces, rather than machining them from large castings. This has made laser beam welding popular, offering high precision with low heat input and distortion, but also high productivity. At the same time, the demand for automation of production has increased, to ensure high quality and consistent results. In turn, the need for sensors to monitor and control the laser welding process is increasing. In laser beam welding without filler material, the gap between the parts to be joined must be narrow. Optical sensors are often used to measure the gap, but with precise machining, it may become so narrow that it is difficult to detect, with the risk of welding in the wrong position. This thesis proposes the use of an inductive sensor with coils on either side of the gap. Inducing currents into the metal, such a sensor can detect even gaps that are not visible. The new feature of the proposal is based on using the complex response of each coil separately to measure the distance and height on both sides of the gap, rather than an imbalance from the absolute voltage of each coil related to gap position. This extra information allows measurement of gap width and alignment as well as position in a working range of about 1 mm around the gap, and decreases the influence from variation in gap alignment to the position measurement. The sensor needs to be calibrated with a certain gap width and height alignment. In real use, these will vary, causing the sensor to be less accurate. Using initial estimates of the gap parameters from the basic sensor, a model ofthe response can be used to estimate the measurement error of each coil, whichin turn can be used for compensation to improve the measurement of the gap properties. The properties of the new method have been examined experimentally, using aprecise traverse mechanism to record single coil responses in a working range around a variable dimension gap, and then using these responses to simulate atwo coil probe. In most cases errors in the measurement of weld gap position and dimensions are within 0.1 mm. Different coil orientations were studied using numerical simulation, and validated in experiments using a two coil probe. The influence of scratches, chamfers and variation in plate thickness was investigated at different frequencies
Inductive measurement of narrow gaps for high precision welding of square butt joints
No full textA recent method in aero engine production is to fabricate components from smaller pieces, rather than machining them from large castings. This has made laser beam welding popular, offering high precision with low heat input and distortion, but also high productivity. At the same time, the demand for automation of production has increased, to ensure high quality and consistent results. In turn, the need for sensors to monitor and control the laser welding process is increasing. In laser beam welding without filler material, the gap between the parts to be joined must be narrow. Optical sensors are often used to measure the gap, but with precise machining, it may become so narrow that it is difficult to detect, with the risk of welding in the wrong position. This kind of problems can cause severe welding defects, where the parts are only partially joined without any visible indication. This thesis proposes the use of an inductive sensor with coils on either side of the gap. Inducing currents into the metal, such a sensor can detect even gaps that are not visible. The new feature of the proposal is based on using the complex response of each coil separately to measure the distance and height on both sides of the gap, rather than an imbalance from the absolute voltage of each coil related to gap position. This extra information allows measurement of gap width and misalignment as well as position, and decreases the influence from gap misalignment to the position measurement. The sensor needs to be calibrated with a certain gap width and height alignment. In real use,these will vary, causing the sensor to be less accurate. Using initial estimates ofthe gap parameters from the basic sensor, a model of the response can be used to estimate the measurement error of each coil, which in turn can be used for compensation to improve the measurement of the gap properties.The properties of the new method have been examined experimentally, using a precise traverse mechanism to record single coil responses in a working range around a variable dimension gap, and then using these responses to simulate a two coil probe. In most cases errors in the measurement of weld gap position and dimensions are within 0.1 mm.The probe is designed to be mounted close to the parts to be welded, and will work in a range of about 1 mm to each side and height above the plates. This is an improvement over previous inductive sensors, that needed to be guided to the mid of the gap by a servo mechanism
Modeling of inductive coil geometry for gap position measurement
No full textFinite element modelling of high frequency inductive coils and metal plates was used to investigate the impedance response to a narrow gap between the plates. The model was used to predict distance sensitivity for both coil-to-gap and coil-to-plate. Different coil axis orientations, along and across the gap and normal to the plate, were modeled, as well as different coil lengths. The model can be used to predict the working range and select orientation and geometry of inductive seam tracking probes with zero gap capability for precision laser beam welding. Different materials, thicknesses and frequencies can be used.</p
A complex response inductive method for improved gap measurement in laser welding
No full textLaser welding needs precise measurement of weldgap position to avoid weld defects. Most often, optical measurement methods are used, but well-aligned narrow gaps canbe difficult to detect. An improved inductive method capable of detecting zero gaps in square butt joints is proposed. The new method uses two eddy current coils, one on each side of the gap, and measures the complex response of the individual coils, i.e. both the inductive and resistive response. By combining the coil responses, both the position and the geometry of the weld gap can be estimated. The method was experimentally investigated by traversing a single coil over an adjustable gap between two plates and combining the measured coil responses into a simulated two-coil probe. The gap was adjusted in both misalignment and gap width up to 0.4 mm. Comparing the results to known settings and positions shows that gap position is measured to within 0.1 mm, if the probe is within a working area of 1 mm from the gap in both position and height. Results from the new method were compared to simulations, from the same experimental data, of a previously reported method where the coils were electrically combined by wiring them together. The previous method can give accurate results but has a much smaller working area and depends on servo actuation to position the probe above the gap. The improved method gives better tolerance to varying misalignment and gap width, which is an advantage over previous inductive methods.</p
Investigation of effects from realistic influences on inductive gap measurement
No full textThe influence of deviations from ideal square butt joint conditions is investigated for an improved inductive gap measurement method. Varying plate thickness, chamfers, and scratches are tested on Alloy 718 at different frequencies in a working range around the gap. Results for different plate thickness show that measurements of position and gap width are affected at all frequencies tested. For a chamfered plate, position measurement is affected for all frequencies, while gap width measurement is less affected at higher frequencies. For both a narrow and a wide scratch, the position measurement at the highest frequency is affected for all scratch locations, while for gap width measurement, only the wide scratch is affecting for all locations. Errors in measurement of probe height and plate alignment are smaller than 0.04 and 0.05 mm for all situations. The results will support in selecting coil frequency and predict results in non-ideal conditions. © 2019</p
Inductive measurement of narrow gaps for high precision welding of square butt joints [Elektronisk resurs]
No full textA recent method in aero engine production is to fabricate components from smaller pieces, rather than machining them from large castings. This has made laser beam welding popular, offering high precision with low heat input and distortion, but also high productivity. At the same time, the demand for automation of production has increased, to ensure high quality and consistent results. In turn, the need for sensors to monitor and control the laser welding process is increasing. In laser beam welding without filler material, the gap between the parts to be joined must be narrow. Optical sensors are often used to measure the gap, but with precise machining, it may become so narrow that it is difficult to detect, with the risk of welding in the wrong position. This kind of problems can cause severe welding defects, where the parts are only partially joined without any visible indication. This thesis proposes the use of an inductive sensor with coils on either side of the gap. Inducing currents into the metal, such a sensor can detect even gaps that are not visible. The new feature of the proposal is based on using the complex response of each coil separately to measure the distance and height on both sides of the gap, rather than an imbalance from the absolute voltage of each coil related to gap position. This extra information allows measurement of gap width and misalignment as well as position, and decreases the influence from gap misalignment to the position measurement. The sensor needs to be calibrated with a certain gap width and height alignment. In real use,these will vary, causing the sensor to be less accurate. Using initial estimates ofthe gap parameters from the basic sensor, a model of the response can be used to estimate the measurement error of each coil, which in turn can be used for compensation to improve the measurement of the gap properties.The properties of the new method have been examined experimentally, using a precise traverse mechanism to record single coil responses in a working range around a variable dimension gap, and then using these responses to simulate a two coil probe. In most cases errors in the measurement of weld gap position and dimensions are within 0.1 mm.The probe is designed to be mounted close to the parts to be welded, and will work in a range of about 1 mm to each side and height above the plates. This is an improvement over previous inductive sensors, that needed to be guided to the mid of the gap by a servo mechanism.</p
Going Beyond Counting First Authors in Author Co-citation Analysis
Get PDFThe present study examines one of the fundamental aspects of author co-citation analysis (ACA) - the way co-citation
counts are defined. Co-citation counting provides the data on which all subsequent statistical analyses and mappings
are based, and we compare ACA results based on two different types of co-citation counting - the traditional type that
only counts the first one among a cited work's authors on the one hand and a non-traditional type that takes into
account the first 5 authors of a cited work on the other hand. Results indicate that the picture produced through this non-traditional author co-citation counting contains more coherent author groups and is therefore considerably clearer. However, this picture represents fewer specialties in the research field being studied than that produced through the traditional first-author co-citation counting when the same number of top-ranked authors is selected and analyzed. Reasons for these effects are discussed
Model based compensation of systematic errors in an inductive gap measurement method
No full textA model-based correction of systematic errors to improve the measurement of gap dimensions in a recently presented method is described. Using one inductive coil on each side of the gap to measure distance and liftoff, the method detects zero width gaps and shows position error less than 0.1 mm. The correction model relies on observations of experimental data, and is calibrated to a small set of measurements. From the initial measurement of gap dimensions, the model estimates errors in each coil to calculate new values for gap width, alignment and height. The errors in the compensated results are within 0.1 mm except for gap width, which still suffers from the effect of combined gap width and misalignment. The method is intended for gap measurement in laser keyhole welding, where the laser beam and the resulting weld seam are very narrow, requiring high precision in alignment and gap preparation.CC BY-NC-ND 4.0Corresponding author at: University West, Nohabgatan 18A, SE-461 53 Trollhättan, Sweden. E-mail address: [email protected] (E. Svenman).The authors gratefully acknowledge the financial support from the Research School SiCoMaP, funded by the Knowledge Foundation, and GKN Aerospace Engine Systems.</p
Variations on the Author
Get PDF“Variations on the Author” discusses two of Eduardo Coutinho’s recent films (Um Dia na Vida, from 2010, and Últimas Conversas, posthumously released in 2015) and their contribution to the general question of documentary authorship. The director’s filmography is characterized by a consistent yet self-effacing form of authorial self-inscription: Coutinho often features as an interviewer that rather than express opinions propels discourses; an interviewer that is good at listening. This mode of self-inscription characterizes him as an author who is not expressive but who is nonetheless markedly present on the screen. In Um Dia na Vida, however, Coutinho is completely absent form the image, while Últimas Conversas, on the contrary, includes a confessional prologue that moves the director from the margins to the center of his films. This article examines the ways in which these works stand out in the filmography of a director who offers new insights into the notion of cinematic authorship
- …
