9 research outputs found
Spectrometry in the Test Beam Line at CTF3
No full textThe CLIC study is based on the so-called two-beam acceleration concept and one of the main goals of the CLIC Test Facility 3 is to demonstrate the efficiency of the CLIC RF power production scheme. As part of this facility a Test Beam Line (TBL), presently under commissioning, is a small-scale version of a CLIC decelerator. To perform as expected the beam line must show efficient and stable RF power production over 16 consecutive decelerating structures. As the high intensity electron beam is decelerated its energy spread grows by up to 60 %. A novel segmented beam dump for time resolved energy measurements has been designed to match the requirements of the TBL. As a complement, a diffusive OTR screen is also installed in the same spectrometer line. The combination of these two devices will provide both a high spatial resolution measurement of both the energy and energy spread and a measurement with a few nanoseconds time response. This paper describes the design of the new segmented dump and presents the results from the first commissioning of the TBL spectrometer line
Production of long bunch trains with 4.5muC total charge using a photoinjector
No full textA photoinjector, PHIN (PHotoINjector), has been realized at CERN by a joint effort of several institutes within the European Coordinated Accelerator Research in Europe program. The test facility has been installed and commissioned at CERN with the aim to demonstrate the beam parameters needed for the CLIC Test Facility 3 (CTF3). This beam is unique with respect to its long bunch train and high average charge per bunch requirements. The nominal beam for CTF3 consists of 1908 bunches each having a 2.33 nC charge and a bunch frequency of 1.5 GHz. Thus, a total charge of ∼4.4 μC has to be extracted and accelerated. The stability of the intensity and the beam parameters along this exceptionally high average current train is crucial for the correct functioning of the CLIC drive beam scheme. Consequently, extensive time-resolved measurements of the transverse and longitudinal beam parameters have been developed, optimized, and performed. The shot-to-shot intensity stability has been studied in detail for the electron and the laser beams, simultaneously. The PHIN photoinjector has been commissioned between 2008 and 2010 during intermittent operations. This paper reports on the obtained results in order to demonstrate the feasibility and the stability of the required beam parameters
Coupling between transverse and longitudinal beam dynamics in the first-stage CLIC decelerator
No full textIn this paper we present the first results of full 6D multi-bunch tracking through the new Drive-Beam decelerator lattice for the first-stage of the Compact Linear Collider (CLIC). Using the new PLACET3 tracking code, we evaluate the coupling between transverse and longitudinal dynamics in the lattice finding an indirect impact of the Drive-Beam's transverse emittance in the Main-Beam performance
Experimental Results from the Test Beam Line in the CLIC Test Facility 3
No full textCERN-ACC-2013-0207</p
High Charge PHIN Photo Injector at CERN with Fast Phase switching within the Bunch Train for Beam Combination
No full textThe high charge PHIN photo-injector was developed within the framework of the European CARE program to provide an alternative to the drive beam thermionic gun in the CTF3 (CLIC Test Facility) at CERN. In PHIN 1908 electron bunches are delivered with bunch spacing of 1.5 GHz and 2.33 nC charge per bunch. Furthermore the drive beam generated by CTF3 requires several fast 180 deg phase-shifts with respect to the 1.5 GHz bunch repetition frequency in order to allow the beam combination scheme developed at CTF3. A total of 8 subtrains, each 140 ns long and shifted in phase with respect to each other, have to be produced with very high phase and amplitude stability. A novel fiber modulator based phase-switching technique developed on the laser system provides this phase-shift between two consecutive pulses much faster and cleaner than the base line scheme, where a thermionic electron gun and sub-harmonic bunching are used. The paper describes the fiber-based switching system and the measurements verifying the scheme. The paper also discusses the latest 8nC charge production and cathode life-time studies on Cs2Te
Performance of Parabolic and Diffusive OTR Screens at the CLIC Test Facility 3
No full textAt the CLIC Test Facility 3, OTR screens are commonly used in beam imaging systems for energy and energy spread characterization in dedicated spectrometer lines. In these lines the horizontal beam size is typically of the order of one centimeter. Already in 2005 a limitation was observed resulting from a strong dependence of the intensity of the light captured by the camera, on the position on the screen (vignetting). The severity of this effect increases with the electron energy, as the aperture of the optical system is finite and the OTR photons are emitted in a small cone of 1/γ angle. To mitigate this effect, different shapes and surface polishing of the screens were investigated. Parabolic and diffusive OTR radiators were tested in several spectrometer lines all along the CTF3 complex. The results are presented in this paper
Performance of the Time Resolved Spectrometer for the 5 MeV Photo-Injector PHIN
No full textThe PHIN photo-injector test facility is being commissioned at CERN to demonstrate the capability to produce the required beam for the 3rd CLIC Test Facility (CTF3), which includes the production of a 3.5A stable beam, bunched at 1.5 GHz with a relative energy spread of less than 1%. A 90◦ spectrometer is instrumented with an OTR screen coupled to a gated intensified camera, followed by a segmented beam dump for time resolved energy measurements. The following paper describes the transverse and temporal resolution of the instrumentation with an outlook towards single-bunch energy measurements
High intensity profile monitor for time resolved spectrometry at the CLIC Test Facility 3
No full textThe power source of the Compact LInear Collider (CLIC) relies on the generation and deceleration of a high-intensity electron drive beam. In order to provide the best radio-frequency (RF) to beam-energy transfer efficiency, the electron beam is accelerated using fully loaded RF cavities, which leads to strong beam loading effects resulting in a high-energy transient. The stability of the RF power produced by the drive beam depends on the stability of the drive beam energy and energy spread along the pulse. The control and the monitoring of the time evolution of the beam energy distribution are therefore crucial for the accelerator performance. For this purpose segmented beam dumps, which are simple and robust devices, have been designed and installed at the CLIC Test Facility 3 (CTF3). These devices are located at the end of spectrometer lines and provide horizontal beam profiles with a time resolution better than 10ns. The segmented dumps are composed of parallel, vertical, metallic plates, and are based on the same principle as a Faraday cup: the impinging beam current is read by a fast acquisition channel. Both FLUKA and Geant4 simulations were performed to define the optimum detector geometry for beam energies ranging from 5MeV to 150MeV. This paper presents a detailed description of the different steps of the design: the optimization of the detector spatial resolution, the minimization of the thermal load and the long-term damage resulting from high radiation doses. Four segmented dumps are currently used in the CTF3 complex. Their measured performance and limitations are presented in this paper. Typical beam spectra as measured in the CTF3 linac are also presented along with a description of the RF manipulations needed for tuning the beam energy spectrum
The CLIC Feasibility Demonstration in CTF3
No full textThe objective of the CLIC Test Facility CTF3 is to demonstrate the feasibility issues of the CLIC two-beam technology: the efficient generation of a very high current drive beam, used as the power source to accelerate the main beam to multi-TeV energies with gradients of over 100 MeV/m, and stable drive beam deceleration. Results of successful beam acceleration with over 100 MeV/m energy gain are shown. Measurements of drive beam deceleration over a chain of Power Extraction Structures (PETS) are presented. The achieved RF power levels, the stability of the power production and of the deceleration are discussed. Finally, we give an overview of the remaining issues to be addressed by the end of 2011
