1,720,957 research outputs found
Caractérisation et amélioration d’un aérateur de surface pour le traitement des eaux
No full textUn nouveau système d’aération de surface pour le traitement des eaux usées a été étudié. Sa spécificité réside dans sa capacité à fonctionner selon deux modes : aération ou simple brassage, en modifiant uniquement le sens de rotation du système. Un pilote a permis de cibler le travail sur l’étude expérimentale du transfert de matière et de l’hydrodynamique. Les champs d'écoulement et les mesures de vitesse à l'intérieur de la cuve agitée ont été réalisés par vélocimétrie laser à effet Doppler (LDV) et par vélocimétrie par images des particules (PIV) pour le mode monophasique (brassage) et pour le mode diphasique (aération). Le transfert d'oxygène se produit à la fois dans la cuve et dans le spray au-dessus de la surface de l'eau. Il a été étudié dans les deux zones. Différentes configurations et conditions opératoires ont été testées afin de comprendre les phénomènes d’interaction : tube de guidage, hélice complémentaire RTP, vitesse de rotation, niveau de submersion des pales de la turbine. La partie expérimentale sur l’hydrodynamique et les champs d'écoulement montre que le mode de fonctionnement en pompage vers le bas (brassage) avec tube de guidage procure les meilleurs résultats en termes de mélange si on se réfère aux champs d'écoulement et à la mesure du temps de mélange. Pour le mode de fonctionnement en pompage vers le haut (aération), les résultats expérimentaux montrent que la configuration du système complet est la plus efficace si on considère le transfert d’oxygène, les vitesses moyennes, l'intensité de l'écoulement turbulent et le temps de mélange. Il est constaté que la meilleure efficacité d'aération standard est atteinte (SAEb = 2.65 kgO2kw-1h-1) lorsque le système complet est utilisé. L'efficacité d'aération standard à 20°C la plus élevée au niveau du spray d'eau est obtenue ((ESP)20 = 51,3%) avec la configuration du système complet. Plusieurs modèles sont proposés pour calculer le transfert d'oxygène dans la cuve et dans le spray, la consommation énergique et le temps de mélange. Ces relations permettent d’évaluer l’influence des différents paramètres géométriques et de fonctionnement dans des systèmes similaires à une échelle industrielle.A new surface aeration system for water and wastewater treatment has been studied. Its uniqueness lies in its ability to operate in two modes: aeration or simply blending (mixing) by just reversing the direction of rotation. An experimental plant has enabled to focus on mass transfer performance and hydrodynamics. The flow pattern and the velocity field measurements inside the agitated tank were performed by both the Laser Doppler Velocimetry (LDV) and the Particle Image Velocimetry (PIV) techniques for the single phase (Mixing) mode and for the two phases (Aeration) mode. The oxygen mass transfer occurs both in the water bulk and in the spray above water surface and has been independently investigated. Different configurations and operational conditions were tested during the experimental part in order to interpret phenomenon effect of the draft tube and RTP propeller, rotational speed, turbine blades submergence and else on the flow field and the oxygen mass transfer in the agitated system that produced mainly by a cone shape turbine. The experimental part dealing with hydrodynamics and flow field shows that the down-pumping operation mode with the draft tube has the most convenient results in the mixing mode with respect to turbulent flow field and mixing time. Whilst for the up-pumping aeration mode the hydrodynamics experimental results show the whole system configuration is the most convenient with regarded to mean velocities, turbulent flow intensity and mixing time. For the oxygen mass transfer experimental part, it is found that the highest standard liquid bulk aeration efficiency is achieved (SAEb = 2.65 kgO2 kw-1h-1) when the whole system configuration is used. The highest standard aeration efficiency at 20°C for the water spray zone is accomplished ((Esp)20 = 51.3 %) with the whole system configuration. Several correlations models have been derived for the oxygen mass transfer in water bulk and spray zones, power consumption and mixing time, on the basis of experimental results. They can be used as tools to estimate these parameters for geometrical and dynamical similar systems at industrial scales
Characterization and improvement of a surface aerator for water treatment
Get PDFUn nouveau système d’aération de surface pour le traitement des eaux usées a été étudié. Sa spécificité réside dans sa capacité à fonctionner selon deux modes : aération ou simple brassage, en modifiant uniquement le sens de rotation du système. Un pilote a permis de cibler le travail sur l’étude expérimentale du transfert de matière et de l’hydrodynamique. Les champs d'écoulement et les mesures de vitesse à l'intérieur de la cuve agitée ont été réalisés par vélocimétrie laser à effet Doppler (LDV) et par vélocimétrie par images des particules (PIV) pour le mode monophasique (brassage) et pour le mode diphasique (aération). Le transfert d'oxygène se produit à la fois dans la cuve et dans le spray au-dessus de la surface de l'eau. Il a été étudié dans les deux zones. Différentes configurations et conditions opératoires ont été testées afin de comprendre les phénomènes d’interaction : tube de guidage, hélice complémentaire RTP, vitesse de rotation, niveau de submersion des pales de la turbine. La partie expérimentale sur l’hydrodynamique et les champs d'écoulement montre que le mode de fonctionnement en pompage vers le bas (brassage) avec tube de guidage procure les meilleurs résultats en termes de mélange si on se réfère aux champs d'écoulement et à la mesure du temps de mélange. Pour le mode de fonctionnement en pompage vers le haut (aération), les résultats expérimentaux montrent que la configuration du système complet est la plus efficace si on considère le transfert d’oxygène, les vitesses moyennes, l'intensité de l'écoulement turbulent et le temps de mélange. Il est constaté que la meilleure efficacité d'aération standard est atteinte (SAEb = 2.65 kgO2kw-1h-1) lorsque le système complet est utilisé. L'efficacité d'aération standard à 20°C la plus élevée au niveau du spray d'eau est obtenue ((ESP)20 = 51,3%) avec la configuration du système complet. Plusieurs modèles sont proposés pour calculer le transfert d'oxygène dans la cuve et dans le spray, la consommation énergique et le temps de mélange. Ces relations permettent d’évaluer l’influence des différents paramètres géométriques et de fonctionnement dans des systèmes similaires à une échelle industrielle. ABSTRACT : A new surface aeration system for water and wastewater treatment has been studied. Its uniqueness lies in its ability to operate in two modes: aeration or simply blending (mixing) by just reversing the direction of rotation. An experimental plant has enabled to focus on mass transfer performance and hydrodynamics. The flow pattern and the velocity field measurements inside the agitated tank were performed by both the Laser Doppler Velocimetry (LDV) and the Particle Image Velocimetry (PIV) techniques for the single phase (Mixing) mode and for the two phases (Aeration) mode. The oxygen mass transfer occurs both in the water bulk and in the spray above water surface and has been independently investigated. Different configurations and operational conditions were tested during the experimental part in order to interpret phenomenon effect of the draft tube and RTP propeller, rotational speed, turbine blades submergence and else on the flow field and the oxygen mass transfer in the agitated system that produced mainly by a cone shape turbine. The experimental part dealing with hydrodynamics and flow field shows that the down-pumping operation mode with the draft tube has the most convenient results in the mixing mode with respect to turbulent flow field and mixing time. Whilst for the up-pumping aeration mode the hydrodynamics experimental results show the whole system configuration is the most convenient with regarded to mean velocities, turbulent flow intensity and mixing time. For the oxygen mass transfer experimental part, it is found that the highest standard liquid bulk aeration efficiency is achieved (SAEb = 2.65 kgO2 kw-1h-1) when the whole system configuration is used. The highest standard aeration efficiency at 20°C for the water spray zone is accomplished ((Esp)20 = 51.3 %) with the whole system configuration. Several correlations models have been derived for the oxygen mass transfer in water bulk and spray zones, power consumption and mixing time, on the basis of experimental results. They can be used as tools to estimate these parameters for geometrical and dynamical similar systems at industrial scales
Caractérisation et amélioration d’un aérateur de surface pour le traitement des eaux
No full textA new surface aeration system for water and wastewater treatment has been studied. Its uniqueness lies in its ability to operate in two modes: aeration or simply blending (mixing) by just reversing the direction of rotation. An experimental plant has enabled to focus on mass transfer performance and hydrodynamics. The flow pattern and the velocity field measurements inside the agitated tank were performed by both the Laser Doppler Velocimetry (LDV) and the Particle Image Velocimetry (PIV) techniques for the single phase (Mixing) mode and for the two phases (Aeration) mode. The oxygen mass transfer occurs both in the water bulk and in the spray above water surface and has been independently investigated. Different configurations and operational conditions were tested during the experimental part in order to interpret phenomenon effect of the draft tube and RTP propeller, rotational speed, turbine blades submergence and else on the flow field and the oxygen mass transfer in the agitated system that produced mainly by a cone shape turbine. The experimental part dealing with hydrodynamics and flow field shows that the down-pumping operation mode with the draft tube has the most convenient results in the mixing mode with respect to turbulent flow field and mixing time. Whilst for the up-pumping aeration mode the hydrodynamics experimental results show the whole system configuration is the most convenient with regarded to mean velocities, turbulent flow intensity and mixing time. For the oxygen mass transfer experimental part, it is found that the highest standard liquid bulk aeration efficiency is achieved (SAEb = 2.65 kgO2 kw-1h-1) when the whole system configuration is used. The highest standard aeration efficiency at 20°C for the water spray zone is accomplished ((Esp)20 = 51.3 %) with the whole system configuration. Several correlations models have been derived for the oxygen mass transfer in water bulk and spray zones, power consumption and mixing time, on the basis of experimental results. They can be used as tools to estimate these parameters for geometrical and dynamical similar systems at industrial scales.Un nouveau système d’aération de surface pour le traitement des eaux usées a été étudié. Sa spécificité réside dans sa capacité à fonctionner selon deux modes : aération ou simple brassage, en modifiant uniquement le sens de rotation du système. Un pilote a permis de cibler le travail sur l’étude expérimentale du transfert de matière et de l’hydrodynamique. Les champs d'écoulement et les mesures de vitesse à l'intérieur de la cuve agitée ont été réalisés par vélocimétrie laser à effet Doppler (LDV) et par vélocimétrie par images des particules (PIV) pour le mode monophasique (brassage) et pour le mode diphasique (aération). Le transfert d'oxygène se produit à la fois dans la cuve et dans le spray au-dessus de la surface de l'eau. Il a été étudié dans les deux zones. Différentes configurations et conditions opératoires ont été testées afin de comprendre les phénomènes d’interaction : tube de guidage, hélice complémentaire RTP, vitesse de rotation, niveau de submersion des pales de la turbine. La partie expérimentale sur l’hydrodynamique et les champs d'écoulement montre que le mode de fonctionnement en pompage vers le bas (brassage) avec tube de guidage procure les meilleurs résultats en termes de mélange si on se réfère aux champs d'écoulement et à la mesure du temps de mélange. Pour le mode de fonctionnement en pompage vers le haut (aération), les résultats expérimentaux montrent que la configuration du système complet est la plus efficace si on considère le transfert d’oxygène, les vitesses moyennes, l'intensité de l'écoulement turbulent et le temps de mélange. Il est constaté que la meilleure efficacité d'aération standard est atteinte (SAEb = 2.65 kgO2kw-1h-1) lorsque le système complet est utilisé. L'efficacité d'aération standard à 20°C la plus élevée au niveau du spray d'eau est obtenue ((ESP)20 = 51,3%) avec la configuration du système complet. Plusieurs modèles sont proposés pour calculer le transfert d'oxygène dans la cuve et dans le spray, la consommation énergique et le temps de mélange. Ces relations permettent d’évaluer l’influence des différents paramètres géométriques et de fonctionnement dans des systèmes similaires à une échelle industrielle
Assessment of Heavy Metals Contamination in Drinking Water of Garmian Region, Iraq
Get PDFDrinking water of safe quality is a critical issue for human survival and health. Water pollution by heavy metals is very crucial because of their toxicity. This study assesses potential of heavy metals pollution in drinking water in Garmian Region, East Iraq. Water samples were investigated for 23 heavy metals and 6 chemical contaminants collected from 16 locations. The analysis was performed by using coupled plasma optical emission spectroscopy (ICPOES, Spectro Arcos). High levels of Al, Se, Sr, and Fe have been detected at certain locations in study area. Statistical analysis techniques of the correlation matrix (CM), and cluster hierarchical analysis (CA) were conducted. The heavy metals pollution index (HPI), heavy metals evaluation index (HEI), and contamination Index (Cd) were used applied. These indices linked with the statistical analysis to interpret relationships among the tested parameters in water samples and to investigate the pollution sources over the study region. Even with the significant correlations between the HPI, Cd, and HEI, they showed dissimilar impact of examined heavy metals on the water quality. The most reliable pollution evaluation index of HEI for drinking water showed that 44% of the water samples is critically polluted. Sources of the contamination are most likely coming from natural geological sources. Anthropogenic impact was only noticed at several sites in the study area
Going Beyond Counting First Authors in Author Co-citation Analysis
Get PDFThe present study examines one of the fundamental aspects of author co-citation analysis (ACA) - the way co-citation
counts are defined. Co-citation counting provides the data on which all subsequent statistical analyses and mappings
are based, and we compare ACA results based on two different types of co-citation counting - the traditional type that
only counts the first one among a cited work's authors on the one hand and a non-traditional type that takes into
account the first 5 authors of a cited work on the other hand. Results indicate that the picture produced through this non-traditional author co-citation counting contains more coherent author groups and is therefore considerably clearer. However, this picture represents fewer specialties in the research field being studied than that produced through the traditional first-author co-citation counting when the same number of top-ranked authors is selected and analyzed. Reasons for these effects are discussed
Variations on the Author
Get PDF“Variations on the Author” discusses two of Eduardo Coutinho’s recent films (Um Dia na Vida, from 2010, and Últimas Conversas, posthumously released in 2015) and their contribution to the general question of documentary authorship. The director’s filmography is characterized by a consistent yet self-effacing form of authorial self-inscription: Coutinho often features as an interviewer that rather than express opinions propels discourses; an interviewer that is good at listening. This mode of self-inscription characterizes him as an author who is not expressive but who is nonetheless markedly present on the screen. In Um Dia na Vida, however, Coutinho is completely absent form the image, while Últimas Conversas, on the contrary, includes a confessional prologue that moves the director from the margins to the center of his films. This article examines the ways in which these works stand out in the filmography of a director who offers new insights into the notion of cinematic authorship
Appropriate Similarity Measures for Author Cocitation Analysis
Get PDFWe provide a number of new insights into the methodological discussion about author cocitation analysis. We first argue that the use of the Pearson correlation for measuring the similarity between authors’ cocitation profiles is not very satisfactory. We then discuss what kind of similarity measures may be used as an alternative to the Pearson correlation. We consider three similarity measures in particular. One is the well-known cosine. The other two similarity measures have not been used before in the bibliometric literature. Finally, we show by means of an example that our findings have a high practical relevance.information science;Pearson correlation;cosine;similarity measure;author cocitation analysis
Dispelling the Myths Behind First-author Citation Counts
Get PDFWe conducted a full-scale evaluative citation analysis study of scholars in the XML research field to explore just how different from each other author rankings resulting from different citation counting methods actually are, and to demonstrate the capability of emerging data and tools on the Web in supporting more realistic citation counting methods. Our results contest some common arguments for the continued
use of first-author citation counts in the evaluation of scholars, such as high correlations between author rankings by first-author citation counts and other citation
counting methods, and high costs of using more realistic citation counting methods that are not well-supported by the ISI databases. It is argued that increasingly available digital full text research papers make it possible for citation analysis studies to go beyond what the ISI databases have directly supported and to employ more
sophisticated methods
- …
