Journal of Mechatronics, Electrical Power, and Vehicular Technology
Not a member yet
258 research outputs found
Sort by
Efficiency improvement of photovolatic by using maximum power point tracking based on a new fuzzy logic controller
No full textMaximum power point tracking (MPPT) is a technique to maximize the power output of photovoltaic (PV). Therefore, to achieve higher PV efficiency, the development of MPPT control algorithm is necessary. Recently, it was revealed that fuzzy logic controller (FLC) is better than other control algorithms and is possible toe developed. This study fabricated and implemented MPPT based on the proposed a new FLC. Input Calculator (IC) via sensors reads current and voltage of PV and generates the comparison of voltage and current of PV, then IC output becomes fuzzy algorithm input. Fuzzy algorithm produces duty cycle that drives synchronous buck converter. The result showed that MPPT system with proposed FLC method has 99.1% efficiency while MPPT system with PO method has 95.5% efficiency. From the obtained result, it can be concluded that the MPPT based on the proposed FLC can increase the overall efficiency of the system to 99.3%
Combustion duration influence on hydrogen-ethanol dual fueled engine emissions: An experimental analysis
No full textThe research presented in this article expresses experimental results on combustion duration effect on the dual fueled engine. In particular, the research was focused on the emissions occurred specifically from a hydrogen-ethanol dual fueled engine. This study was performed on a compression ignition engine that was converted to run and act as a spark ignition engine. This modified engine was fueled by hydrogen–ethanol with various percentage substitutions of hydrogen. The substitution was altered from 20 to 80% at a constant speed of 1500 rpm. The various engine emission characteristics such as CO, Hydrocarbon, and NOx were experimentally determined. This study resulted that at a compression ratio of 11:1 and combustion duration of 25°CA, the best operating conditions of the engine were shown. Moreover, the optimum fuel combination was established at 60 to 80% of hydrogen substitution to ethanol. The experimental results also revealed that at 100% load and at compression ratios 7, 9, and 11; the CO and HC emissions have decreased while NOx increased and followed with the increase in the percentage of hydrogen addition and combustion duration. It was concluded that the retarding combustion duration was preferred for NOx emission control in the engine
Preliminary investigation of sleep-related driving fatigue experiment in Indonesia
No full textSleep-related driving fatigue has been recognised as one main cause of traffic accidents. In Indonesia, experiment-based driving fatigue study is still very limited, therefore it is necessary to develop laboratory-based experiment procedure for sleep-related fatigue study. In this preliminary study, we performed a literature review to find references for the procedure and three pilot experiments to test the instruments and procedure to be used in measuring driving fatigue. Three subjects participated, both from experienced and inexperienced drivers. Our pilot experiments were performed on a driving simulator using OpenDS software with brake and lane change test reaction time measurement. We measured sleepiness by using Karolinska Sleepiness Scale (KSS) Questionnaire. The conditions of the experiment were based on illumination intensity as well as pre- and post-lunch session. We found that lane change reaction time is more potential than brake reaction time to measure driving performance as shown by the more fluctuating data. Post-lunch seems to induce drowsiness greater than illumination intensity. KSS questionnaire seems non-linear with driving performance data. We need to test further these speculations in the future studies involving a sufficient number of subjects. We also need to compare the effect of circadian rhythm and sleep deprivation on driving fatigue. The use of eye closure and physiological measurement in further study will enable us to measure driving fatigue more objectively. Considering the limitations, more preliminary experiments are required to be performed before conducting the main experiment of driving fatigue
Thermal efficiency and emission characteristics of a diesel-hydrogen dual fuel CI engine at various loads condition
No full textEfforts to find alternative fuels and reduce emissions of CI engines have been conducted, one of which is the use of diesel hydrogen dual fuel. One of the goals of using hydrogen in dual-fuel combustion systems is to reduce particulate emissions and increase engine power. This study investigates the thermal efficiency and emission characteristics of a diesel-hydrogen dual fuel CI engine at various loads condition. The hydrogen was used as a secondary fuel in a single cylinder 667 cm3 diesel engine. The hydrogen was supplied to intake manifold by fumigation method, and diesel was injected directly into the combustion chamber. The results show that the performance test yielding an increase around 10% in the value of thermal efficiency of diesel engines with the addition of hydrogen either at 2000 or 2500 rpm. Meanwhile, emission analyses show that the addition of hydrogen at 2000 and 2500 rpm lead to the decrease of NOx value up to 43%. Furthermore, the smokeless emissions around 0% per kWh were occurred by hydrogen addition at 2000 and 2500 rpm of engine speeds with load operation under 20 Nm
Pendulum energy harvester with amplifier
No full textThis paper presents a new principle of inductive vibration power harvester. Harvester is a pendulum that uses energy capacitor which is the mass. The mass is connected to the pendulum via a gearbox to achieve greater movement of the pendulum that generates an electromagnetic voltage. The harvester is developed at a very low frequency (1-10 Hz) which uses the rectified magnetic fluxes. Magnets are statically placed in the harvester case, and relative motion is carried out by the coil. Magnets are static, and the coil moves due to the weight ratio of magnets which the steel leads of the magnetic flux and the coil itself. This paper is focused on a harvester with a mechanical amplifier with the proposed technique is brings the plow harvester access with an auxiliary force. The experimental results indicate that the optimal results of the harvester with an accumulator for the resonant zone are 3.75 Hz, 7 Hz, and 10 Hz
Designing optimal speed control with observer using integrated battery-electric vehicle (IBEV) model for energy efficiency
No full textThis paper develops an optimal speed control using a linear quadratic integral (LQI) control standard with/without an observer in the system based on an integrated battery-electric vehicle (IBEV) model. The IBEV model includes the dynamics of the electric motor, longitudinal vehicle, inverter, and battery. The IBEV model has one state variable of indirectly measured and unobservable, but the system is detectable. The objectives of this study were: (a) to create a speed control that gets the exact solution for a system with one indirect measurement and unobservable state variable; and (b) to create a speed control that has the potential to make a more efficient energy system. A full state feedback LQI controller without an observer is used as a benchmark. Two output feedback LQI controllers are designed; including one controller uses an order-4 observer and the other uses an order-5 observer. The order-4 observer does not include the battery state of charge as an observer state whereas the order-5 observer is designed by making all the state variable as the observer state and using the battery state of charge as an additional system output. An electric passenger minibus for public transport with 1500 kg weight was used as the vehicle model. Simulations were performed when the vehicle moves in a flat surface with the increased speed from stationary to 60 km/h and moves according to standard NEDC driving profile. The simulation results showed that both the output feedback LQI controllers provided similar speed performance as compared to the full state feedback LQI controller. However, the output feedback LQI controller with the order-5 observer consumed less energy than with the order-4 observer, which is about 10% for NEDC driving profile and 12% for a flat surface. It can be concluded that the LQI controller with order-5 observer gives better energy efficiency than the LQI controller with order-4 observe
