Munzur University Institutional Repository
Not a member yet
1113 research outputs found
Sort by
PERSISTENCE OF TWO SULPHONYLUREA HERBICIDES IN WHEAT PLANTED FIELD, THRACE REGION IN TURKEY
. This study is concerning the environmental fate of chlorsulfuron and tribenuron-methyl
herbicide in a wheat planted field at Thrace Region in Turkey. Use of herbicides containing these
active ingredients is advised in the Marmara region in Turkey for cereal agriculture. The study was
conducted in wheat planted fields where these herbicides were used. Over nine months, in each
two or three week periods, soil samples were obtained from selected sampling points and herbicide
residuals were determined by gas chromatography with electron capture detector (GC-ECD) and
high performance liquid chromatography-mass spectrometry (HPLC-MS). As a result of these studies, persistence of chlorsulfuron was determined as approximately 1.2% at the second half of June,
2016 and tribenuron methyl seemed to be approximately 1% at the end of May, 2016. The results of the present study showed that chlorsulfuron is generally adsorbed weakly by soil when compared
to tribenuron-methyl. pH, organic material, climatic factors and clay content of soil were the main factors influencing the adsorption and desorption properties of the herbicides. The results of this
study demonstrated that chlorsulfuron and tribenuron-methyl residues in the soil might depend on their different chemical structures, soil temperature, precipitation and humidity
Farklı oranlardaki demirin astacus leptodactylus(esch., 1823)' lardaki yaşama oranı, oksidatif stres Fe, Cu, Cr ve Zn seviyeleri üzerine etkileri
Bu çalışmada, erkek tatlısu istakozu (Astacus leptodactylus) rasyonlarına farklı oranlarda demir (Fe) katılmasının; tatlısu istakozunun (kerevit) yaşama oranı, hepatopankreas ve karapaksdaki demir (Fe), bakır (Cu), Çinko (Zn), Krom (Cr) ve lipid peroksidasyon (Malondialdehit (MDA)) düzeyleri üzerine etkisinin ortaya konması amaçlandı. Bu amaçla, bir kontrol (K) ve dört adet deneme (F1, F2, F3, F4) rasyonu hazırlandı. Rasyon öğeleri kontrol rasyonuna 28 mg/kg demir katkısı sağlamaktadır. Kontrol rasyonuna 50 mg kg-1, 100 mg kg-1,200 mg kg-1 ve 300 mg kg-1 demir sülfat katılarak sırasıyla F1, F2, F3 ve F4 rasyonları oluşturuldu. Çalışma üç tekrar halinde gerçekleştirildi.
Sonuç olarak, araştırmada tatlı su istakozu kontrol rasyonuna farklı oranlarda demir katılmasının; A. leptodactylus’un yaşama oranını etkilemediği görüldü. Dokulardaki Cr değeri standartların altında olduğundan dolayı tespit edilemedi. Karapaks da MDA değeri belirlenemedi. Hepatopankreasda MDA olarak belirlenen lipid peroksidasyon düzeyini önlemede kontrol rasyonuna 300 mg kg-1demir ilavesinin yeterli olduğu bulundu. Ayrıca bu çalışmada yemdeki demir miktarının dokulardaki Fe, Cu ve Zn birikimi üzerinde etkili olduğu görüldü.Munzur Üniversitesi Bilimsel Araştırma Projeleri (MUNİBAP), Proje No: YLTUB016-1
Adsorption study of Lead Ions from Aaueous solutions on pumice
Abstract— Heavy metals in water and wastewaters are one of the most important problems for the environment and human health. Lead is one of the most toxic heavy metals. It is widely used in many applications such as, production of lead acid batteries, solder, alloys, ammunition, pigments, glazes and plastic stabilizers. According to WHO permitted limitation of lead in drinking water is 10 µg/L. Therefore, lead in water resources should be removed to decrease amount of it. In this study, the removal of lead ion from aqueous solution by pumice was investigated in a batch adsorption system. Adsorption dosage, initial metal ion concentration, and pH on metal ion removal has been studied. Batch adsorption experiments were carried out at 20 oC, in 150 mL conical flasks. The solutions containing Pb+2 ions were prepared by dissolving weighed quantities of Pb(NO3)2.4H2O in distilled water. In each adsorption test, after the volume of 50 mL lead solution at a definite initial concentration (0.005-0.05 mmol/L was placed into the glass flask, a given amount of adsorbent (0.2-0.5 g) was added to solution. The average particle size of pumice sample used in the study was -200 mesh. Flask content was shaken at 200 rpm for various contact time. At the end of the experiment time, lead ions remaining in solution was determined by flame AAS (Perkin Elmer AAnalyst 800). The amount of lead adsorbed by pumice was calculated from difference between the ion concentration before and after process. While the initial concentration, initial pH of solution, contact time, stirring speed and adsorbent dosage were 0.01 mmol/L, 5.25, 180 min, 200 rpm, and 0.4 g, respectively, the efficiency of lead adsorption on pumice was 98 %
Conformal, concircular, quasi-conformal and conharmonic flatness on normal complex contact metric manifolds
Conformal, concircular, quasi-conformal and conharmonic curvature tensors play an important role in Riemannian geometry. In this paper, we study on normal complex contact metric manifolds under flatness conditions of these tensors
Ortadoğu'daki darbeler - Mısır örneği
Ortadoğu XX. Yüzyılın başlarından itibaren büyük olaylara sahne oldu. I.
Dünya Savaşı sonunda bölge parçalanarak sömürgeleştirildi. Bu uygulamalar
bölgedeki sıkıntıları daha da arttırdı. II. Dünya Savaşı’na kadar bölgede;
Siyonistlerin Yahudi Devleti kurma gayretleri, emperyal devletlerin burada
daha fazla nüfuz elde etme mücadeleleri, bölge halklarının savaş sırasında
vaat edilen bağımsız devletlerine kavuşma çabaları yaşanmıştır. Birbirinden
tamamen farklı olan bu beklentiler, iki dünya savaşı arasında bölgedeki
sıkıntıları daha da attırmıştır.
Ortadoğu ilk çağlardan beri ""Ön Asya, Batı Asya, Güneybatı Asya" gibi
değişik adlarla anılmıştır. I. Dünya Savaşı’ndan sonra da bunlara "Yakın doğu
ve Ortadoğu" deyimleri eklenmiştir. Ortadoğu'nun sınırlarının çizilmesinin
zorluğu, bölgenin belirgin bir coğrafi birim olmamasından kaynaklanmaktadır.
En dar bakış açısıyla Ortadoğu; Türkiye, İran, Mısır üçgeni ve bu üçgenin
içinde kalan ülkeleri kapsar. En geniş bakış açısıyla Ortadoğu; Avrupa, Asya
ve Afrika kıtalarının birbirine yaklaştığı, Türkiye, İran, Mısır üçgenine komşu
olan Müslüman ülkeleri, yani kabaca doğuda Afganistan ile batıda Kuzey
Afrika, Sudan, Somali gibi bölgeleri içine alan sahadır. Zaman içinde Batı'nın bölgedeki çıkarları ve müdahalelerinin gelişmesiyle Ortadoğu tanımı
değişikliklere uğramıştır. Ortadoğu; dünya ticaretine coğrafi konumu ve içinde
bulunan Süveyş Kanalı, Basra Körfezi, Çanakkale-İstanbul Boğazları, Akdeniz
Limanları gibi önemli suyolları ve onları birbirine bağlayan kara yolları ile yön
verebilecek önemli bir bölgedir. Kısacası insanlık tarihinin ve uygarlığın adeta
beşiği olan Ortadoğu, daha önceki asırlarda olduğu gibi, XX. yüzyılda da
dünyanın en önemli bölgelerinden biri olma özelliğini sürdürmüştür.
Ekonomik, politik ve askeri yönden Ortadoğu'yu bu kadar önemli yapan başka
etkenler de vardır. Şöyle ki: Ortadoğu dünyanın en büyük petrol rezervlerine
sahiptir. Buradaki petrollerin kaliteli ve maliyetinin ucuz olması, XX.
yüzyıldan itibaren bölgenin öneminin en hayati cihetini teşkil etmiştir.
Mısır, 1882’den itibaren ülke yönetimini kontrol altına alan İngiltere’nin
yönetiminde ve Muhammed Ali’nin reformlarının da bir sonucu olarak on
dokuzuncu yüzyıl sonlarında Ortadoğu’nun en zengin merkezlerinden birisi
haline gelmişti. Ülke bölgedeki en geniş ve zengin üretim merkezi olmasının
yanı sıra etnik ve dinsel çeşitlilik bakımından da zengin bir sermaye sınıfına
ev sahipliği yapmaktaydı. En geniş sermaye sınıfı mutamassirun adı verilen
‘Mısırlılaşmış yabancılardı. Daha sonraki dönemlerde ‘komprador burjuvazi’
olarak görülecek olan mutamassirun’ların yanı sıra büyük toprak sahipleri de
ekonomide ve daha sonra siyasette yerlerini almaya başlamaktaydı.
Endüstriyel gelişmeye baktığımızda ise genel olarak İngiliz ve Fransız etkisini
görmek mümkündür. Mısır 1922’de bağımsızlığını kazanmış olsa da ülke
siyasetinde ve ekonomisinde İngiliz ve genel olarak Batılı devletlerin etkisi
sürmeye devam etti. Bu etkiye rağmen milli kalkınma için çabalar da
görülmeye başlamıştır. 1920’de Bank Mısır’ın kurulmasının ardından yerel
sanayiyi geliştirecek ve yerel yatırımcılara yatırım olanakları sağlayacak
kaynaklar sunulmaya başlanmıştır
Change of mechanical properties of powder recyclate reinforced polyolefin based on gamma radiation
In this study, the changes observed in the mechanical properties of standard test specimens that were produced with powder coating reinforced polyolefin (polyethylene and polypropylene) due to gamma radiation were examined. Matrix material of these specimens included low density polyethylene and polypropylene and 5%, 10%, 20%, 30%, 40% and 50% electrostatic powder coating waste by weight, and the samples were exposed to 44 kGry gamma-radiation for twenty four hours. Mechanical tests applied to the specimens after radiation demonstrated that the physical bonding mechanism between matrix material and filler material was reinforced. In the mechanical tests, tensile strength, three-point bending strength, and Izod impact strength of the samples were investigated and the results were compared to the results obtained in the mechanical tests when they were not radiated. Thus, the effects of gamma radiation on the mechanical properties of the filler material, and the electrostatic powder coating reinforced polyethylene and polypropylene were determined. Furthermore, section images of the radiated samples were taken with a scanning electron microscope and compared to the section images of irradiated samples to observe the physical bonding mechanism
Seasonal Changes In Antıoxıdant Defence System On Brown Trout (Salmo Sp.) In Munzur Stream
The aim of the present study was to evaluate the oxidant and antioxidant status of the indigenous
brown trout (Salmo sp.) caught from Munzur stream (Tunceli, Turkey) at different seasons in different tissues. Glutathione peroxidase (GPx), catalase (CAT), superoxide dismutase (SOD), total antioxidant status (TAS) and total oxidant status (TOS) levels were measured. These measurements were read in a microplate reader using commercial kits with ELISA method. At the end of the study, significant variations of oxidative stress biomarkers were observed between seasons and tissues. The results of this study
show that oxidative stress responses in tissues of Salmo sp. are sensitive to the tissues and the seasons
in relation to the contaminants, climatic parameters and reproductive period in Munzur stream. The selected parameters are in valuable biomarkers for monitoring of water systems since at molecular levels they give an early warning signal of xenobiotics on aquatic organisms. It was concluded that the measurement of antioxidants biomarkers known such as SOD, CAT and GSH-Px activities, TAS and
TOS levels may also be promising indicators of an oxidant impact on aquatic organisms
Box–Behnken Design Approach for Optimizing Removal of Copper from Wastewater Using a Novel and Green Adsorbent
The aim of the present
research was to apply the
Box–Behnken experimental
design and response surface
methodology for modeling of
copper (Cu2+) ions from an industrial wastewater and leachate pretreated astragalus herbal plant.
A three factor, three level
Box–Behnken experimental
design combined with response
surface modeling (RSM) and quadratic programming (QP) was
employed for maximizing Cu(II)
removal from aqueous solution
based on 17 different experimental data obtained in a batch experimental study. Three independent
variables (pH ranging from 2.0 to
8.0, contact time from 10 to 180
minutes, and adsorbent amount
from 0.1 to 1 g) were studied.
The significance of the independent variables and their interactions were tested by means of the
analysis of variance (ANOVA)
with 95% confidence limits. The standardized effects of the independent variables and their interactions on the dependent variable
were also investigated by preparing a Pareto chart. The optimum
values of the selected variables
were obtained by solving the quadratic regression model as well as
by analyzing the response surface
contour plots. Using the experimental conditions of pH = 5.0,
contact time = 92.5 minutes,
adsorbent dosage = 0.25 g, the
recovery efficiency of Cu(II) was
found to be 100%.
Copper-free and copperloaded astragalus was analyzed
using fourier transform infrared
spectrometry (FTIR) which evidenced the functional groups
involved in copper uptake.
Adsorption equilibrium for copper was described by using the
Freundlich and Langmiur adsorption isotherms. This adsorbent
was applied to different industrial
wastewater and leachate samples
for copper remova
The efficacy of chamomile (Matricaria chamomilla) oil as a promising anaesthetic agent for two freshwater aquarium fish species
The efficacy of anesthetic chamomile oil (from Matricaria chamomilla L.) was evaluated in two freshwater aquarium fish species, Electric Blue Hap (Sciaenochromis fryeri) and Yellow Princess (Labidochromis caeruleus). Fish were exposed to ten concentrations of anesthetic (0.1, 0.2, 0.3, 0.4, 0.5, 0.6, 0.7, 0.8, 0.9 and 1.0 ml/L). The optimal concentrations identified as 0.6 ml/L for deep anesthesia (A5) for both two species. The minimal sedative concentration at the stage of loss of equilibrium (A3) was found to be 0.3 ml/L. The induction time generally decreased significantly with increasing concentrations of chamomile oil for all treatment groups. Recovery time tended to increase with increased chamomile oil at concentrations lower than 0.7 ml/L, but after this concentration it decreased. Chamomile oil proved to be effective as an anesthetic for both ornamental fish species. These findings suggest that chamomile oil is a promising anesthetic agent for aquaculture. However, further studies should be focused on species based investigations on the effect of temperature, transfer of fish, and their effect on antioxidant and oxidant status, in order to gather further information
Pleistocene glaciations in Karadağ, Western Taurus Mountains, Turkey
Karadağ, Teke Yarımadasında Beydağları, Akdağ ve Sandıras gibi Pleyistosen buzullaşmasına maruz kalmış
dağlardan biridir. Karadağ, Fethiye Körfezi’nin hemen kuzeydoğusunda 30 km kuş uçuşu mesafede 2418 m zirveye
ulaşır ve 2300 m üzerinde birçok yükseltiye sahiptir. Teke Yarımadasında Pleyistosen buzullaşmalarına uğramış
dağlardan, Sandıras ve Akdağ ile ilgili buzul araştırmalarına ve buzullaşmaların yaşlandırmalarına yönelik çalışmalar
varken, Beydağları’nda Pleyistosen buzullaşmalarından sadece çok genel hatları ile bahsedilmiş, Karadağ ile ilgili
buzullaşma olgusu bilinmemekte, başka bir deyişle buzullardan bahseden hiçbir çalışma bulunmamaktadır. Oysaki
Karadağ yüksek zirve düzlüklerinin yamaçlarında belirgin sirk ve morenler barındırır. Yapılan arazi çalışmalarında,
Karadağ’da iki gelişmiş buzul vadisi, farklı büyüklükte ve yönlerde gelişmiş üç tane sirk ve bunların önlerinde 1800
m seviyelerine inen cephe ve tümseksi (hummocky) morenleri gözlenmiştir. Bu çalışma ile Türkiye’de yeni bir
buzullaşma sahası tespit edilmiş ve Türkiye Buzullaşma Envanteri’ne katkı yapılmıştır. Yeni buzullaşma alanının
jeomorfolojik, klimatolojik özelliklerini ortaya koymayı hedefleyen bu çalışmada; tektonik, klimatik ve karstik
özellikler göz önüne alınarak Karadağ’da Pleyistosen’deki jeomorfolojik gelişimi açıklanmaya çalışılmıştır. Arazi
çalışmaları, insansız hava aracı ve meteoroloji istasyonlarının verilerinden elde edilen mekânsal veriler coğrafi bilgi
sistemleri kullanılarak analiz edilmiş, sonuç harita ve çıktılar oluşturulmuştur.Karadağ is one of the mountains subjected to the Pleistocene glaciations in the Teke Peninsula (Western Taurus) along with Beydağları, Akdağ, and Sandıras Mountains. Karadağ, which reaches 2418 m summit at a 30 km straight distance from the northeast of Fethiye Bay, has many peaks over 2300 m. There are plenty of glacial researches and dating studies aim to reveal Pleistocene glaciation chronology of the mountains such as Sandıras
and Akdağ in the Teke Peninsula. On the other hand, glaciations in Beydağları were mentioned superficially and in general terms. Lastly, there has not been known any glaciation phenomenon in Karadağ, in other words there are not any studies concerning the glaciation on the mountain. However, Karadağ has distinctive cirques and moraines on the slopes of high elevations near the peak. In this study, we identified glacial valleys, cirques developed in different
sizes and aspects and lastly frontal and hummocky moraines in front of these cirques. They are descending to the elevation of 1800 m. With this study, a new glacial area was identified in Turkey and made a contribution to the glaciation inventory of Turkey. This study aims to reveal the geomorphological and climatological characteristics of
this area with regard to tectonic, climatic and karstic characteristics during Pleistocene. Maps and relevant outputs were created and analyzed by geographic information systems using the spatial data obtained from the field studies, unmanned aerial vehicles and meteorological stations