1,721,100 research outputs found
On the biomechanics of the hip: relevance of femoral anteversion for hip contact force and loading using a short-stemmed prostheses (in German)
No full textShort-stemmed hip implants were established in total hip arthroplasty in the last years. Also patients with secondary osteoarthritis of the hip with pathological anteversion of the femoral neck are treated increasingly using this method. Therefore an investigation was performed to analyze the resulting hip contact force and femoral loading in the proximal femur at the solid model of the “standardized femur”. Two different situations of femoral component anteversion were simulated. Increased hip contact forces and an increase of medial and lateral cortex loads result in the anteverted model. With present level of knowledge about the influence of the hip contact force the use of short-stemmed implants is not uncritically in patients with degenerative osteoarthritis of the hip combined with rotational disorders of the proximal femur. The selection of the tribological pairing is to be considered more strongly regarding the wear behavior
The influence of alignment on the musculo-skeletal loading conditions at the knee
No full textBackground and AimHigh tibial osteotomies attempt to recreate physiologically normal joint loading. Previous studies have discussed the influence of mal-alignment on the distribution of static loads to the medial and lateral compartments of the knee. The aim of this study was to determine the influence of mal-alignment on the tibio-femoral loading conditions during dynamic activities. Material and MethodsUsing a musculo-skeletal model of the lower limb, which had been previously validated with in vivo data, in this study we modified the alignment of the knee in four patients, from a normal position to the extremes of 8 degrees valgus and 10 degrees varus mal-alignment. The resulting tibio-femoral joint contact forces were examined while patients were walking and stair climbing. ResultsVarying the mal-alignment resulted in a highly individual response in joint loads. Deviations from the normal alignment produced an increase in loading, with valgus generating a more rapid increase in loading than a varus deformity of the same amount. Varus deformities of 10 degrees resulted in increases in peak contact force from an average of 3.3-times bodyweight (BW) up to a peak of 7.4 BW (+45% to +114%) while patients were walking, whilst increases of 15% up to 35% were determined for stair climbing. Increases of up to 140% were calculated at 8 degrees valgus during walking and up to 53% for stair climbing. ConclusionThis study demonstrated a clear dependence of the individual joint loads on axial knee alignment. Based on the sensitivity of joint loading to valgus mal-alignment, more than 3 degrees of over-correction of a varus deformity to valgus should be carefully reconsidered
Physiologically based boundary conditions in finite element modelling
No full textFinite element analysis has been used extensively in the study of bone loading and implant performance, such as in the femur. The boundary conditions applied vary widely, generally producing excessive femoral deformation, and although it has been shown that the muscle forces influence femoral deflections and loading, little consideration has been given to the displacement constraints. It is hypothesised that careful application of physiologically-based constraints can produce physiological deformation, and therefore straining, of the femur. Joint contact forces and a complete set of muscle forces were calculated based on the geometry of the Standardized Femur using previously validated musculoskeletal models. Five boundary condition cases were applied to a finite element model of the Standardized Femur: A) diaphyseally-constrained with hip contact and abductor forces; B) case A plus vasti forces; C) case A with complete set of muscle forces; D) distally-constrained with all muscle forces; E) physiological constraints with all muscle forces. It was seen that only the physiological boundary conditions, case E, produced physiological deflections (<2.0mm) of the femoral head in both the coronal and sagittal planes, which resulted in minimal reaction forces at the constrained nodes. Strains in the mid-diaphysis varied by up to 600 micro-strain under walking loads and 1000 micro-strain under stair climbing loads. The mode of loading, as indicated by the strain profiles on the cortex also varied substantially under these boundary conditions, which has important consequences for studies that examine localised bone loading such as fracture or bone remodelling simulations
Mechanical conditions in the initial phase of bone healing
No full textBackgroundBone healing is sensitive to the initial mechanical conditions with tissue differentiation being determined within days of trauma. Whilst axial compression is regarded as stimulatory, the role of interfragmentary shear is controversial. The purpose of this study was to determine how the initial mechanical conditions produced by interfragmentary shear and torsion differ from those produced by axial compressive movements. MethodsThe finite element method was used to estimate the strain, pressure and fluid flow in the early callus tissue produced by the different modes of interfragmentary movement found in vivo. Additionally, tissue formation was predicted according to three principally different mechanobiological theories. FindingsLarge interfragmentary shear movements produced comparable strains and less fluid flow and pressure than moderate axial interfragmentary movements. Additionally, combined axial and shear movements did not result in overall increases in the strains and the strain magnitudes were similar to those produced by axial movements alone. Only when axial movements where applied did the non-distortional component of the pressure-deformation theory influence the initial tissue predictions. InterpretationThis study found that the mechanical stimuli generated by interfragmentary shear and torsion differed from those produced by axial interfragmentary movements. The initial tissue formation as predicted by the mechanobiological theories was dominated by the deformation stimulus
A survey of formal methods for determining the centre of rotation of ball joints
No full textThe determination of an accurate centre of rotation (CoR) from segment marker positions is of interest across a wide range of applications, but particularly for clinical gait analysis and for estimating the hip joint centre during surgical intervention of the knee, for limb alignment purposes. For the first time in this survey of formal methods, we classify, analyse and compare different methods (geometric, algebraic, bias compensated algebraic, and Pratt sphere fit methods, as well as the centre transformation technique, the Holzreiter approach, the helical pivot technique, the Schwartz transformation techniques, the minimal amplitude point method and the Stoddart approach) for the determination of spherical joint centres from marker position data. In addition, we propose a new method, the symmetrical CoR estimation or SCoRE, in which the coordinates of the joint centre must only remain constant relative to each segment, thus not requiring the assumption that one segment should remain at rest. For each method, 1000 CoR estimations were analysed with the application of isotropic, independent and identically distributed Gaussian noise (standard deviation 0.1 cm) to each of the marker positions, to all markers on the segment simultaneously and the two in combination. For the test conditions used here, most techniques were capable of determining the CoR to within 0.3 cm, as long as the spherical range of motion (RoM) of the joint was 45° or more. Under the most stringent conditions tested, however, the SCoRE was capable of best determining the CoR, to within approximately 1.2 mm with a RoM of 20°. The correct selection and application of these methodologies should help improve the accuracy of surgical navigation and clinical kinematic measurement
Going Beyond Counting First Authors in Author Co-citation Analysis
Full text linkThe present study examines one of the fundamental aspects of author co-citation analysis (ACA) - the way co-citation
counts are defined. Co-citation counting provides the data on which all subsequent statistical analyses and mappings
are based, and we compare ACA results based on two different types of co-citation counting - the traditional type that
only counts the first one among a cited work's authors on the one hand and a non-traditional type that takes into
account the first 5 authors of a cited work on the other hand. Results indicate that the picture produced through this non-traditional author co-citation counting contains more coherent author groups and is therefore considerably clearer. However, this picture represents fewer specialties in the research field being studied than that produced through the traditional first-author co-citation counting when the same number of top-ranked authors is selected and analyzed. Reasons for these effects are discussed
The quality of bone surfaces may govern the use of model based fluoroscopy in the determination of joint laxity
No full textThe assessment of knee joint laxity is clinically important but its quantification remains elusive. Calibrated, low dosage fluoroscopy, combined with registered surfaces and controlled external loading may offer possible solutions for quantifying relative tibio-femoral motion without soft tissue artefact, even in native joints. The aim of this study was to determine the accuracy of registration using CT and MRI derived 3D bone models, as well as metallic implants, to 2D single-plane fluoroscopic datasets, to assess their suitability for examining knee joint laxity. Four cadaveric knees and one knee implant were positioned using a micromanipulator. After fluoroscopy, the accuracy of registering each surface to the 2D fluoroscopic images was determined by comparison against known translations from the micromanipulator measurements. Dynamic measurements were also performed to assess the relative tibio-femoral error. For CT and MRI derived 3D femur and tibia models during static testing, the in-plane error was 0.4 mm and 0.9 mm, and out-of-plane error 2.6 mm and 9.3 mm respectively. For metallic implants, the in-plane error was 0.2 mm and out-of-plane error 1.5 mm. The relative tibio-femoral error during dynamic measurements was 0.9 mm, 1.2 mm and 0.7 mm in-plane, and 3.9 mm, 10.4 mm and 2.5 mm out-of-plane for CT and MRI based models and metallic implants respectively. The rotational errors ranged from 0.5° to 1.9° for CT, 0.5–4.3° for MRI and 0.1–0.8° for metallic implants. The results of this study indicate that single-plane fluoroscopic analysis can provide accurate information in the investigation of knee joint laxity, but should be limited to static or quasi-static evaluations when assessing native bones, where possible. With this knowledge of registration accuracy, targeted approaches for the determination of tibio-femoral laxity could now determine objective in vivo measures for the identification of ligament reconstruction candidates as well as improve our understanding of the consequences of knee joint instability in TKA
Variations on the Author
Full text link“Variations on the Author” discusses two of Eduardo Coutinho’s recent films (Um Dia na Vida, from 2010, and Últimas Conversas, posthumously released in 2015) and their contribution to the general question of documentary authorship. The director’s filmography is characterized by a consistent yet self-effacing form of authorial self-inscription: Coutinho often features as an interviewer that rather than express opinions propels discourses; an interviewer that is good at listening. This mode of self-inscription characterizes him as an author who is not expressive but who is nonetheless markedly present on the screen. In Um Dia na Vida, however, Coutinho is completely absent form the image, while Últimas Conversas, on the contrary, includes a confessional prologue that moves the director from the margins to the center of his films. This article examines the ways in which these works stand out in the filmography of a director who offers new insights into the notion of cinematic authorship
Repeatability and reproducibility of OSSCA: a functional approach for assessing the kinematics of the lower limb
No full textMarker-based gait analysis of the lower limb that uses assumptions of generic anatomical morphology can be susceptible to errors, particularly in subjects with high levels of soft tissue coverage. We hypothesize that a functional approach for assessing skeletal kinematics, based on the application of techniques to reduce soft tissue artefact and functionally identify joint centres and axes, can more reliably (repeatably and reproducibly) assess the skeletal kinematics than a standard generic regression approach. Six healthy adults each performed 100 repetitions of a standardized motion, measured on four different days and by five different observers. Using OSSCA, a combination of functional approaches to reduce soft tissue artefact and identify joint centres and axes, the lengths of the femora and tibiae were determined to assess the inter-day and inter-observer reliability, and compared against a standard generic regression approach. The results indicate that the OSSCA was repeatable and reproducible (ICC lowest bound 0.87), but also provided an improvement over the regression approach (ICC lowest bound 0.69). Furthermore, the analysis of variance revealed a statistically significant variance for the factor “observers” (p < 0.01; low-reproducibility) when using the regression approach for determining the femoral lengths. Here, this non-invasive, rapid and robust approach has been demonstrated to allow the repeatable and reproducible identification of skeletal landmarks, which is insensitive to marker placement and measurement session. The reliability of the OSSCA thus allows its application in clinical studies for reducing the uncertainty of approach-induced systematic errors
- …
