1,721,275 research outputs found
Spray characterization for engine combustion network Spray G injector using high-fidelity simulation with detailed injector geometry
No full textThis article presents a computational fluid dynamics study of the engine combustion network Spray G, focusing on the transient characteristics of the spray during the start of injection and the impacts of nozzle geometry details derived from the manufacturing process. The large-eddy-simulation method, coupled with the volume-of-fluid method, was used to model the high-speed turbulent two-phase flow. A moving-needle boundary condition was applied to capture the internal flow boundary condition accurately. The injector geometry was measured with micron-level resolution using X-ray tomographic imaging at the Advanced Photon Source at Argonne National Laboratory, providing detailed machining tolerance and defects from manufacturing and a realistic rough surface. For comparison, a nominal geometry and a modified geometry incorporating measured large-scale geometric features but no surface details were also used in the simulations. Spray characteristics such as mass flow rate, injection velocity, and Sauter mean diameter were analyzed. Significantly distinct spray characteristics in terms of injection velocity, spray morphology, and primary breakup mechanism were predicted using different nozzle geometries, which is mainly attributable to the realistic surface finish and manufacturing defects. The measured high-resolution geometry predicts a lower injection velocity, a wider-spreading spray, and an overall slower breakup rate with evident injector tip wetting compared to the ideally smooth nozzle boundary. This result implies that the manufacturing details of the injector, which are usually ignored in fuel injection studies, have a significant impact on the spray development process and should be taken into account for design optimization
Highly resolved Eulerian simulations of fuel spray transients in single and multi-hole injectors: Nozzle flow and near-exit dynamics
No full textIn high pressure fuel injectors, needle opening and closing transients cause complex off-design fluid dynamics behaviors that profoundly impact the spray and mixture formation processes. These dynamics are completely different from what is known to occur in steady state conditions. In this study, diesel spray transients have been investigated in single-hole and 3-hole nozzles, encompassing internal and external nozzle flow and including needle motion, performing highly resolved (2.5 μm) computational fluid dynamics (CFD) simulations. We focused on end-of-injection (EOI) and start-of-injection (SOI) processes, in order to provide insights in to the physics. The liquid fuel, vapor and gas species are modeled with a single-fluid multiphase mixture approach, with diffuse interface, and with large eddy simulations (LES) of the turbulence. Occurrence of phase change due to cavitation is accounted for, and the spray dispersion is described with a turbulent dispersion model. Detailed needle motion data and orifice internal surface are available from x-ray synchrotron source measurements carried out at Argonne National Laboratory, and shared through the Engine Combustion Network (ECN) community. Simulations are compared against x-ray phase contrast imaging and radiography of the internal and near-exit flow, in addition to optical microscopy data of the near-exit sprays. Simulation results are found to agree well with available experimental data, and are able to realistically capture local and global features. The simulations allow to gain insight into the physics of gas ingestion and dribbles at EOI, for different hole diameters, operating conditions and number of holes. At SOI, timing of liquid appearance out of the injector and spray tip penetration are adequately predicted, by using the EOI flow field as in-nozzle initialization, and by prescribing the measured tip needle displacement with an informed effective valve opening point inferred from the x-ray observations. Lastly, the variation of spreading angle over time is also discussed in detail for the multi-hole case, including hole-to-hole variations. Due to real geometry features and asymmetric needle motion with eccentric components, it is found that the three holes exhibit swirling flows of increasing intensity as the lift decreases, causing the near cone angle to open and spread, in a quasi-hollow cone structure. These features are not observed in axial single-hole injectors because of their relative simplicity and intrinsic symmetry
Investigation of Homogeneous Relaxation Model Parameters and their Implications for Gasoline Injectors
No full textFlash boiling is known to be a common phenomenon for gasoline direct injection (GDI) engine sprays. The Homogeneous Relaxation Model has been adopted in many recent numerical studies for predicting cavitation and flash boiling. The Homogeneous Relaxation Model is assessed in this study. Sensitivity analysis of the model parameters has been documented to infer the driving factors for the flash-boiling predictions. The model parameters have been varied over a range and the differences in predictions of the extent of flashing have been studied. Apart from flashing in the near-nozzle regions, mild cavitation is also predicted inside the gasoline injectors. The variation in the predicted time scales through the model parameters for predicting these two different thermodynamic phenomena (cavitation, flash) have been elaborated in this study. Turbulence model effects have also been investigated by comparing predictions from the standard and Re-Normalization Group (RNG) k−ε turbulence models
CFD Modeling of the Nozzle Flow and Near-field Spray on ECN Spray B Injector
No full textIt is important to understand the fluid dynamics inside the diesel injector and flow development in the
nozzle due to their direct impact on the fuel-air mixing and combustion. This work uses a Eulerian approach
and performs fully coupled simulations of the injector flow and near-field spray. This approach
treats the liquid fuel and gas phases as a single mixture in the nozzle and near nozzle dense sprays. The
liquid fuel mass fraction is transported with a model for the turbulent liquid diffusion flux using a Volume-
of-Fluid method. The cavitation is modeled by the homogeneous relaxation model. A standard kepsilon
turbulence model is used with round-jet correction. The well-characterized ECN spray B injector
is simulated under the x-ray radiography measurement conditions. The transient flow development and
cavitation phenomena are analyzed in details. The effect of the needle motion on the flow and hole-tohole
variations is discussed. A comparison between the multi-hole injector and single-hole Spray A injector
is also conducted
Going Beyond Counting First Authors in Author Co-citation Analysis
Full text linkThe present study examines one of the fundamental aspects of author co-citation analysis (ACA) - the way co-citation
counts are defined. Co-citation counting provides the data on which all subsequent statistical analyses and mappings
are based, and we compare ACA results based on two different types of co-citation counting - the traditional type that
only counts the first one among a cited work's authors on the one hand and a non-traditional type that takes into
account the first 5 authors of a cited work on the other hand. Results indicate that the picture produced through this non-traditional author co-citation counting contains more coherent author groups and is therefore considerably clearer. However, this picture represents fewer specialties in the research field being studied than that produced through the traditional first-author co-citation counting when the same number of top-ranked authors is selected and analyzed. Reasons for these effects are discussed
Variations on the Author
Full text link“Variations on the Author” discusses two of Eduardo Coutinho’s recent films (Um Dia na Vida, from 2010, and Últimas Conversas, posthumously released in 2015) and their contribution to the general question of documentary authorship. The director’s filmography is characterized by a consistent yet self-effacing form of authorial self-inscription: Coutinho often features as an interviewer that rather than express opinions propels discourses; an interviewer that is good at listening. This mode of self-inscription characterizes him as an author who is not expressive but who is nonetheless markedly present on the screen. In Um Dia na Vida, however, Coutinho is completely absent form the image, while Últimas Conversas, on the contrary, includes a confessional prologue that moves the director from the margins to the center of his films. This article examines the ways in which these works stand out in the filmography of a director who offers new insights into the notion of cinematic authorship
Appropriate Similarity Measures for Author Cocitation Analysis
Full text linkWe provide a number of new insights into the methodological discussion about author cocitation analysis. We first argue that the use of the Pearson correlation for measuring the similarity between authors’ cocitation profiles is not very satisfactory. We then discuss what kind of similarity measures may be used as an alternative to the Pearson correlation. We consider three similarity measures in particular. One is the well-known cosine. The other two similarity measures have not been used before in the bibliometric literature. Finally, we show by means of an example that our findings have a high practical relevance.information science;Pearson correlation;cosine;similarity measure;author cocitation analysis
Influence of turbulence and thermophysical fluid properties on cavitation erosion predictions in channel flow geometries
No full textCavitation and cavitation-induced erosion have been observed in fuel injectors in regions of high acceleration and low pressure. Although these phenomena can have a large influence on the performance and lifetime of injector hardware, questions still remain on how these physics should be accurately and efficiently represented within a computational fluid dynamics model. While several studies have focused on the validation of cavitation predictions within canonical and realistic injector geometries, it is not well documented what influence the numerical and physical parameters selected to represent turbulence and phase change will have on the predictions for cavitation erosion propensity and severity. In this work, a range of numerical and physical parameters are evaluated within the mixture modeling approach in CONVERGE to understand their influence on predictions of cavitation, condensation and erosion. Particular attention is paid to grid resolution, turbulence model and near-wall treatment, fuel surrogate properties, and non-condensable gas content. Assessment of cavitation predictions are conducted through comparison of measured and predicted mass flow rates and cavitation probability distributions for flow through a channel with a sharp inlet. Predictions for hydrodynamic impact loading and cavitation erosion are compared with the experimentally measured incubation period and critical site for erosion. Based on these findings, recommendations are provided for modeling turbulent cavitating flows, using the single fluid mixture modeling approach, to improve predictions for cavitation-induced erosion. In particular, to capture the fluid dynamic phenomena characterizing cavitation cloud formation, development and shedding, a Large Eddy simulation with grid resolution as fine as 2.50 μm is recommended. The assumed concentration of non-condensable gas content is observed to have a strong influence on the predicted cavitation erosion severity, which motivates the need for dissolved gas concentration measurements for future cavitation erosion experimental studies. Using the best practices established in this work, good agreement is achieved between the measured and predicted cavitation parameters, as well as the critical site for cavitation-induced erosion
- …
