15 research outputs found
The mercury imaging X-ray spectrometer (MIXS) on bepicolombo
No full textThe Mercury Imaging X-ray Spectrometer (MIXS) on the BepiColombo Mercury Planetary Orbiter (MPO) will measure fluorescent X-ray emission from the surface of Mercury in the energy range 0.5–7.5 keV, which is induced by incident solar X-rays and solar wind electrons and protons. These X-rays will reveal the elemental composition of the surface of Mercury and aid the determination of the planet's evolution.
MIXS is a two component instrument. A collimated channel (MIXS-C) provides measurements on scales of 70–270 km, sufficient to separate the major Mercurian terrains. A second channel (MIXS-T) is the first imaging X-ray telescope for planetary remote sensing and will make measurements on spatial scales of less than 10 km for major elements during solar flares, sufficient to isolate surface landforms, such as craters and their internal structures. The spatial resolution achieved by MIXS-T is made possible by novel, low mass microchannel plate X-ray optics, in a Wolter type I optical geometry.
MIXS measurements of surface elemental composition will help determine rock types, the evolution of the surface and ultimately a probable formation process for the planet. In this paper we present MIXS and its predicted performance at Mercury as well as discussing the role that MIXS measurements will play in answering the major questions about Mercury
Active X-ray optics for the next generation of X-ray space telescopes
No full textDescribed within is the design, manufacture, metrology and X-ray testing of an active X-ray
prototype intended for the next generation of X-ray telescopes. One of the challenges faced by
the X-ray telescope community is how to combine high resolution and high sensitivity into one
system, as weight limitations place constraints on the optics that can be launched. Therefore the
mandate of the active X-ray prototype is to provide high sensitivity through the ability of the optics
to be nested and to deliver high angular resolution through the active control of the optic’s form.
Piezoelectric unimorph actuators provide the active component: it is intended that they will correct
for figure errors within the optic and therefore increase the angular resolution capability.
The prototype’s design is based upon an ellipsoidal segment which provides point-to-point
focussing of an X-ray source. The prototype itself is composed of an electroformed nickel optic
where the non-reflective surface is populated with 30 piezoelectric actuators and it is the production
of the prototype that is the core of the presented research. Metrology of the actuators’ influence
functions is presented and highlight the prototype’s ability to deform its optic surface by microns.
In addition, the measured influence functions are compared against finite element models and a
distinct similarity between the functions is observed.
The prototype was tested at an X-ray beamline facility in November 2008 and the results
showed the prototype’s ability to correct the optic to achieve an improved angular resolution: from
0.786 arc-minutes to 0.686 arc-minutes in terms of full width half maximum. Finally, difficulties
in the manufacture of the prototype and X-ray testing shall be presented alongside future work in
conclusion to this thesis
A Wide Field Auroral Imager (WFAI) for low Earth orbit missions
No full textAbstract. A comprehensive understanding of the solar wind interaction with Earth's coupled magnetosphere-ionosphere system requires an ability to observe the charged particle environment and auroral activity from the same platform, generating particle and photon image data which are matched in time and location. While unambiguous identification of the particles giving rise to the aurora requires a Low Earth Orbit satellite, obtaining adequate spatial coverage of aurorae with the relatively limited field of view of current space bourne auroral imaging systems requires much higher orbits. A goal for future satellite missions, therefore, is the development of compact, wide field-of-view optics permitting high spatial and temporal resolution ultraviolet imaging of the aurora from small spacecraft in low polar orbit. Microchannel plate optics offer a method of achieving the required performance. We describe a new, compact instrument design which can observe a wide field-of-view with the required spatial resolution. We report the focusing of 121.6 nm radiation using a spherically-slumped, square-pore microchannel plate with a focal length of 32 mm and an F number of 0.7. Measurements are compared with detailed ray-trace simulations of imaging performance. The angular resolution is 2.7±0.2° for the prototype, corresponding to a footprint ~33 km in diameter for an aurora altitude of 110 km and a spacecraft altitude of 800 km. In preliminary analysis, a more recent optic has demonstrated a full width at half maximum of 5.0±0.3 arcminutes, corresponding to a footprint of ~1 km from the same spacecraft altitude. We further report the imaging properties of a convex microchannel plate detector with planar resistive anode readout; this detector, whose active surface has a radius of curvature of only 100 mm, is shown to meet the spatial resolution and sensitivity requirements of the new wide field auroral imager (WFAI).
</jats:p
