1,720,962 research outputs found
Manifold and Port Design for Balanced Flow and Increased Turbulence in a Two-Stroke, Opposed Piston Engine
No full textTwo-stroke, opposed piston engines have gained recent attention for their improved thermal efficiency relative to the conventional inline or V-configuration. One advantage of twostroke, opposed piston engines is a reduction in heat losses since there is no cylinder head. Another advantage is improved gas exchange via uniflow scavenging since the exhaust and intake ports may be located near bottom dead center of the exhaust and intake pistons, respectively. One challenge with the design of two-stroke engines is promoting turbulence within the cylinder. Turbulence is important for mixing air and fuel in the cylinder and for increasing flame speed during combustion.This work investigates the flow and turbulence through two-stroke, opposed piston engines using computational fluid dynamics (CFD). Specifically, the role of intake manifold and intake port geometry on turbulence within the cylinder was investigated by systematically modifying the engine geometry. Turbulence was then quantified using three metrics: circulation around the cylinder axis (swirl), circulation normal to the cylinder axis (tumble), and volume average turbulent kinetic energy (TKE) within the cylinder.Increasing the swirl angle from 0 degrees to 10 degrees increased the in-cylinder swirl by a factor of 3. Increasing the swirl angle also increased the volume average TKE by a range of 7.6% to 36.5% across the three cylinders of the engine. A reverse tilt angle of 15 degrees increased tumble circulation near the piston face but decreased tumble circulation by a factor of 3 near the center of the cylinder. The next step for research on this would be to apply more geometric manipulations to the manifold of the swirl engine design to balance the mass flow rate for each port. Following the redesign of the manifold the next step is to perform a dynamic CFD test to verify the mass flow has been balanced under a dynamic scenario
Electric Infrared Die Heating for Aluminum High Pressure Die Casting
No full textCasting is a substantial part of modern manufacturing and production, typically used in the production of aluminum alloys. The high pressure die casting process is extremely suitable for mass production. Due to the high volume, wasted time and resources during the production cycle become more significant. Aluminum die castings require the die to be at elevated temperatures to produce acceptable castings. When the inner surfaces of a die are cold, the outer shell of the casting will cool too rapidly, and solidification of the outer shell occurs before the aluminum has time to uniformly fill the cavities. Therefore, without the die being within the proper temperature range, the castings produced will have significant issues in porosity and casting incompleteness. Furthermore, stresses are introduced to the casting surfaces when warm-up shots are used to raise the temperature prior to production. In the present work, research is conducted on designing a heating method for a casting die used in the manufacturing of an automotive transmission intermediate plate. An electric, short wave infrared heating system is simple and effective for the purpose. By utilizing an electric infrared heater in combination with a flat mirror reflector, the aluminum high pressure die casting die was heated to 300°C surface temperature within 30 minutes. Further research can be done to optimize heat flux distribution and minimize energy consumption
Natural Air Circulation Model Development for the DigIndy Tunnel
No full textThe DigIndy tunnel is an extension of the Indianapolis combined sewer system that stores the combined sewer overflow during heavy rain conditions. The tunnel system has several openings in and around the city of Indianapolis. Gasses emitted from the tunnel may create health concerns and affect the quality of life for nearby residents. Understanding the air circulation patterns provides valuable insight into where gases are likely to emerge from the tunnel and what steps may be taken to mitigate gas emissions in undesirable locations. The objective of the present work is to develop a computational fluid dynamics (CFD) model capable of predicting the air circulation patterns in the DigIndy tunnel under dry weather conditions. In order to inform and validate the CFD model, an experimental campaign was designed and executed to measure weather data and air flow rates within the DigIndy tunnel. Obtaining accurate results requires careful consideration of key physical phenomena to include in the model, geometric simplification strategies, mesh generation strategies, and numerical modeling strategies. Results showed that the seasonal effect, manifest by thermally-driven flow, plays a significant role in the air circulation patterns within the tunnel. Furthermore, results show that tunnel alignment affects the natural air circulation within the tunnel. Large diameter shafts, as the working and retrieval shafts, lead to significant circulation rates in the new tunnel alignments
3D Printing Suppressor for Small Arms Using Fused Deposition Modeling
No full textMetal 3D printing is the industry standard for manufacturing experimental suppressors due to the limitations of conventional, subtractive machining methods. Long print times, difficulty sintering, and cleaning of metal 3D printed suppressor components limit the development time. Plastic printed components are able to be produced quicker, safer, and at a lower cost than their metal 3D printed counterparts. Reducing the time and cost of manufacturing will allow for an increased pace of innovations in suppressor design.Utilizing Finite Element Analysis (FEA) in combination with Computational Fluid Dynamics (CFD) will expedite the process of designing 3D printed plastic suppressors. Solidworks FEA determined the maximum stress applied to the blast chamber of the plastic suppressor. ANSYS Fluent CFD simulations were used to qualitatively compare the sound pressure levels of an unsuppressed and suppressed 22LR pistol. Comparing the results of the CFD simulations gave insight into the effectiveness of the selected baffle structure.A prototype 3D printed suppressor was optimized for strength according to manufacturing practices for printed plastic small arms. Testing occurred at an indoor range where peak impulse noise was measured for an unsuppressed 22LR pistol and a plastic printed suppressor. The printed suppressor reduced the small arms impulse noise from 150.5 dB(spl) to 132.4 dB(spl). Impulse noises below the pain threshold of 140 dB(spl) do not require hearing protection for operation. Utilizing FEA, CFD, and FDM prototyping methods in this work has laid the foundation for future works in the rapid prototyping and optimizations of suppressors for small arms
Optimizing Port Geometry and Exhaust Lead Angle in Opposed Piston Engines
No full textA growing global population and improved standard of living in developing countries have resulted in an unprecedented increase in energy demand over the past several decades. While renewable energy sources are increasing, a huge portion of energy is still converted into useful work using heat engines. The combustion process in diesel and petrol engines releases carbon dioxide and other greenhouse gases as an unwanted side-effect of the energy conversion process. By improving the efficiency of internal combustion engines, more chemical energy stored in petroleum resources can be realized as useful work and, therefore, reduce global emissions of greenhouse gases. This research focused on improving the thermal efficiency of opposed-piston engines, which, unlike traditional reciprocating engines, do not use a cylinder head. The cylinder head is a major source of heat loss in reciprocating engines. Therefore, the opposed-piston engine has the potential to improve overall engine efficiency relative to inline or V-configuration engines.The objective of this research project was to further improve the design of opposed-piston engines by using computational fluid dynamics (CFD) modeling to optimize the engine geometry. The CFD method investigated the effect of intake port geometry and exhaust piston lead angle on the scavenging process and in-cylinder turbulence. After the CFD data was analyzed, scavenging efficiency was found insensitive to transfer port geometry and exhaust piston lead angle with a maximum change of 0.61%. Trapping efficiency was altered exclusively by exhaust piston lead angle and changed from 18% to 26% as the lead angle was increased. The in-cylinder turbulence parameters of the engine (normalized swirl circulation, normalized tumble circulation, and normalized TKE) experienced more complex relationships. All turbulence parameters were sensitive to changing transfer port geometry and exhaust piston lead angle. Some examples of trends seen during the analysis include: an increase in normalized swirl circulation from 0.01 to 4.45 due to changes in swirl angle, a change in normalized tumble circulation from -28.52 to 21.11 as swirl angle increased, and an increase in normalized tumble circulation from 14.20 to 33.68 as exhaust piston lead angle was increased. Based on the present work, an optimum configuration was identified for a swirl angle of 15°, a tilt angle of 10°, and an exhaust piston lead angle of 20°. Future work includes expanding the numerical model’s domain to support a complete cylinder-port configuration, adding combustion products to the diffusivity equation in the UDF, and running additional test cases to describe the entire input space for the sensitivity analysis
Going Beyond Counting First Authors in Author Co-citation Analysis
Get PDFThe present study examines one of the fundamental aspects of author co-citation analysis (ACA) - the way co-citation
counts are defined. Co-citation counting provides the data on which all subsequent statistical analyses and mappings
are based, and we compare ACA results based on two different types of co-citation counting - the traditional type that
only counts the first one among a cited work's authors on the one hand and a non-traditional type that takes into
account the first 5 authors of a cited work on the other hand. Results indicate that the picture produced through this non-traditional author co-citation counting contains more coherent author groups and is therefore considerably clearer. However, this picture represents fewer specialties in the research field being studied than that produced through the traditional first-author co-citation counting when the same number of top-ranked authors is selected and analyzed. Reasons for these effects are discussed
Variations on the Author
Get PDF“Variations on the Author” discusses two of Eduardo Coutinho’s recent films (Um Dia na Vida, from 2010, and Últimas Conversas, posthumously released in 2015) and their contribution to the general question of documentary authorship. The director’s filmography is characterized by a consistent yet self-effacing form of authorial self-inscription: Coutinho often features as an interviewer that rather than express opinions propels discourses; an interviewer that is good at listening. This mode of self-inscription characterizes him as an author who is not expressive but who is nonetheless markedly present on the screen. In Um Dia na Vida, however, Coutinho is completely absent form the image, while Últimas Conversas, on the contrary, includes a confessional prologue that moves the director from the margins to the center of his films. This article examines the ways in which these works stand out in the filmography of a director who offers new insights into the notion of cinematic authorship
Appropriate Similarity Measures for Author Cocitation Analysis
Get PDFWe provide a number of new insights into the methodological discussion about author cocitation analysis. We first argue that the use of the Pearson correlation for measuring the similarity between authors’ cocitation profiles is not very satisfactory. We then discuss what kind of similarity measures may be used as an alternative to the Pearson correlation. We consider three similarity measures in particular. One is the well-known cosine. The other two similarity measures have not been used before in the bibliometric literature. Finally, we show by means of an example that our findings have a high practical relevance.information science;Pearson correlation;cosine;similarity measure;author cocitation analysis
Dispelling the Myths Behind First-author Citation Counts
Get PDFWe conducted a full-scale evaluative citation analysis study of scholars in the XML research field to explore just how different from each other author rankings resulting from different citation counting methods actually are, and to demonstrate the capability of emerging data and tools on the Web in supporting more realistic citation counting methods. Our results contest some common arguments for the continued
use of first-author citation counts in the evaluation of scholars, such as high correlations between author rankings by first-author citation counts and other citation
counting methods, and high costs of using more realistic citation counting methods that are not well-supported by the ISI databases. It is argued that increasingly available digital full text research papers make it possible for citation analysis studies to go beyond what the ISI databases have directly supported and to employ more
sophisticated methods
- …
