1,720,986 research outputs found
1D numerical study on hydrogen injection enabling ultra-lean combustion in a small gasoline Spark Ignition engine
Full text linkThis paper deals with the effects of hydrogen port injection on combustion evolution, efficiency and exhaust emissions of a small turbocharged gasoline Spark-Ignition engine through a 1D numerical code. First, the experiments on the base engine architecture are performed at different speeds and at low/medium loads. The experimental findings are used to validate a 1D model of the whole engine, developed within a commercial code. 1D model is also refined with "user-defined"sub-models for an accurate description of the in-cylinder phenomena, namely turbulence, combustion, heat transfer, and emissions. In a second step, 1D model is virtually modified through the installation of an hydrogen injector in each intake runner, while the combustion sub-model also accounts for the impact of hydrogen addition on the laminar flame speed through a dedicated correlation. 1D simulations are performed at low/medium loads and fixed speed of 2250 rpm with 5% of hydrogen by volume in the intake air. Numerical investigations show that hydrogen addition to gasoline/air mixtures allows relevant efficiency benefits (up to a maximum percent gain of 19%), while the NO emissions are almost eliminated. Consequently, hydrogen-boosted combustion represents a potential solution to achieve very high efficiency and reduced pollutant emissions of gasoline spark ignition engines equipped with a conventional combustion system
Individual cylinder combustion optimization to improve performance and fuel consumption of a small turbocharged SI engine
Full text linkStringent exhaust emission and fuel consumption regulations impose the need for new solutions for further development of internal combustion engines. With this in mind, a refined control of the combustion process in each cylinder can represent a useful and affordable way to limit cycle-to-cycle and cylinder-to-cylinder variation reducing CO2 emission. In this paper, a twin-cylinder turbocharged Port Fuel Injection–Spark Ignition engine is experimentally and numerically characterized under different operating conditions in order to investigate the influence of cycle-to-cycle variation and cylinder-to-cylinder variability on the combustion and performance. Significant differences in the combustion behavior between cylinders were found, mainly due to a non-uniform effective in-cylinder air/fuel (A/F) ratio. For each cylinder, the coefficients of variation (CoVs) of selected combustion parameters are used to quantify the cyclic dispersion. Experimental-derived CoV correlations representative of the engine behavior are developed, validated against the measurements in various speed/load points and then coupled to an advanced 1D model of the whole engine. The latter is employed to reproduce the experimental findings, taking into account the effects of cycle-to-cycle variation. Once validated, the whole model is applied to optimize single cylinder operation, mainly acting on the spark timing and fuel injection, with the aim to reduce the specific fuel consumption and cyclic dispersion
Water spray flow characteristics under synthetic jet driven by a piezoelectric actuator
Full text linkParticle Image Velocimetry (PIV) and Phase Doppler Anemometry (PDA) have been applied to investigate the droplets size and velocity distribution of a water spray, under the control of a piezo-element driven synthetic jet (SJ). Tests were carried out under atmospheric conditions within a chamber test rig equipped with optical accesses at two injection pressures, namely 5 and 10 MPa, exploring the variation of the main spray parameters caused by the synthetic jet perturbations. The SJ orifice has been placed at 45° with respect to the water spray axis; the nozzle body has been moved on its own axis and three different nozzle quotes were tested. PIV measurements have been averaged on 300 trials whereas about 105 samples have been acquired for the PDA tests. For each operative condition, the influence region of the SJ device on the spray has been computed through a T-Test algorithm. The synthetic jet locally interacts with the spray, energizing the region downstream the impact. The effect of the actuator decreases at higher injection pressures and moving the impact region upwards. Droplets coalescence can be detected along the synthetic jet axis, while no significant variations are observed along a direction orthogonal to it
Impact of cooled EGR on performance and emissions of a turbocharged spark-ignition engine under low-full load conditions
No full textThe stringent worldwide exhaust emission legislations for CO2 and pollutants require significant efforts to increase both the combustion efficiency and the emission quality of internal combustion engines. With this aim, several solutions are continuously developed to improve the combustion efficiency of spark ignition engines. Among the various solutions, EGR represents a well-established technology to improve the gasoline engine performance and the nitrogen-oxides emissions. This work presents the results of an experimental investigation on the effects of the EGR technique on combustion evolution, knock tendency, performance and emissions of a small-size turbocharged PFI SI engine, equipped with an external cooled EGR system. Measurements are carried out at different engine speeds, on a wide range of loads and EGR levels. The standard engine calibration is applied at the reference test conditions. Then, the exhaust gas is recirculated and the load is controlled by adjusting the intake pressure, the injection and the spark timing. The main results show a significant reduction in specific fuel consumption at low load due to the lower pumping losses when EGR is active, independent on the engine speed. At high load, a lower improvement in fuel economy has been found, mainly due to a slight reduction in the knock tendency. EGR results in a reduction in NO emission at each engine speed and load, with penalties in HC emission
Performance and emissions of a spark ignition engine fueled with water-in-gasoline emulsion produced through micro-channels emulsification
Full text linkThis paper presents an experimental study investigating the effects of water-in-gasoline emulsion (WiGE) on the performance and emissions of a turbocharged PFI spark-ignition engine. The emulsions were produced through a micro-channels emulsifier, potentially capable to work inline, without addition of surfactants. Measurements were performed at a 3000 rpm speed and net Indicated Mean Effective Pressure (IMEP) of 16 bar: the engine point representative of commercial ECU map was chosen as reference. In this condition, the engine, fueled with gasoline, runs over-fueled (λ = 0.9) to preserve the integrity of the turbocharger from excessive temperature, and the spark timing corresponds to the knock limit. Starting from the reference point, two different water contents in emulsion were tested, 10% and 20% by volume, respectively. For each selected emulsion, at λ = 0.9, the spark timing was advanced from the reference point value to the new knock limit, controlling the IMEP at a constant level. Further, the cooling effect of water evaporation in WiGE allowed it to work at stoichiometric condition, with evident benefits on the fuel economy. Main outcomes highlight fuel consumption improvements of about 7% under stoichiometric mixture and optimized spark timing, while avoiding an excessive increase in turbine thermal stress. Emulsions induce a slight worsening in the HC emissions, arising from the relative impact on combustion development. On the other hand, at stoichiometric condition, HC and CO emissions drop with a corresponding increase in NO
Exploring the potentials of water injection to improve fuel consumption and torque in a small displacement PFI spark-ignition engine
No full textEffect of cylinder-by-cylinder variation on performance and gaseous emissions of a pfi spark ignition engine: Experimental and 1d numerical study
Full text linkCombustion stability, engine efficiency and emissions in a multi-cylinder spark-ignition internal combustion engines can be improved through the advanced control and optimization of individual cylinder operation. In this work, experimental and numerical analyses were carried out on a twin-cylinder turbocharged port fuel injection (PFI) spark-ignition engine to evaluate the influence of cylinder-by-cylinder variation on performance and pollutant emissions. In a first stage, experimental tests are performed on the engine at different speed/load points and exhaust gas recirculation (EGR) rates, covering operating conditions typical of Worldwide harmonized Light-duty vehicles Test Cycle (WLTC). Measurements highlighted relevant differences in combustion evolution between cylinders, mainly due to non-uniform effective in-cylinder air/fuel ratio. Experimental data are utilized to validate a one-dimensional (1D) engine model, enhanced with user-defined sub-models of turbulence, combustion, heat transfer and noxious emissions. The model shows a satisfactory accuracy in reproducing the combustion evolution in each cylinder and the temperature of exhaust gases at turbine inlet. The pollutant species (HC, CO and NOx) predicted by the model show a good agreement with the ones measured at engine exhaust. Furthermore, the impact of cylinder-by-cylinder variation on gaseous emissions is also satisfactorily reproduced. The novel contribution of present work mainly consists in the extended numerical/experimental analysis on the effects of cylinder-by-cylinder variation on performance and emissions of spark-ignition engines. The proposed numerical methodology represents a valuable tool to support the engine design and calibration, with the aim to improve both performance and emissions
Experimental and 1D Numerical Investigations on the Exhaust Emissions of a Small Spark Ignition Engine Considering the Cylinder-by-Cylinder Variability
No full textThis paper reports a numerical and experimental analysis on a twin-cylinder turbocharged Spark Ignition engine carried out to investigate the cylinder-to-cylinder variability in terms of performance, combustion evolution and exhaust emissions. The engine was tested at 3000 rpm in 20 different steady-state operating conditions, selected with the purpose of observing the influence of cylinder-by-cylinder A/F ratio variations and the EGR effects on the combustion process and exhaust emissions for low to medium/high loads. The experimental outcomes showed relevant differences in the combustion evolution (characteristic combustion angles) between cylinders and not negligible variations in the emissions of the single cylinder exhaust and the overall engine one. This misalignment resulted to be due to differences in the injected fuel amount by the port injectors in the two cylinders, mainly deriving from the specific fuel rail geometry. The experimental data were then used to validate a 1D engine model, integrated with refined sub-models of turbulence, combustion, heat transfer and emissions. The model takes into account the in-cylinder production of noxious species, and their propagation in the exhaust system, up to the three-way catalytic converter. A satisfactory accuracy was reached in reproducing the overall engine performance and the combustion process in the two cylinders. In particular, the emission sub-models confirmed that the variations of the cylinder-out exhaust emissions (NOx, HC and CO) were mainly due to the non-uniform effective in-cylinder A/F ratio. The proposed numerical methodology has the potential to highlight unexpected combustion non-uniformities among different cylinders and represents a powerful support to the engine design and development. It also allows for the prediction of the overall exhaust emissions at different engine operating conditions up to the entire domain, thus assisting the engine calibration phase and reducing the experimental efforts
Going Beyond Counting First Authors in Author Co-citation Analysis
Full text linkThe present study examines one of the fundamental aspects of author co-citation analysis (ACA) - the way co-citation
counts are defined. Co-citation counting provides the data on which all subsequent statistical analyses and mappings
are based, and we compare ACA results based on two different types of co-citation counting - the traditional type that
only counts the first one among a cited work's authors on the one hand and a non-traditional type that takes into
account the first 5 authors of a cited work on the other hand. Results indicate that the picture produced through this non-traditional author co-citation counting contains more coherent author groups and is therefore considerably clearer. However, this picture represents fewer specialties in the research field being studied than that produced through the traditional first-author co-citation counting when the same number of top-ranked authors is selected and analyzed. Reasons for these effects are discussed
- …
