1,721,000 research outputs found
Management Implications of Using Brush Mats for Soil Protection on Machine Operating Trails during Mechanized Cut-to-Length Forest Operations
No full textMechanized cut-to-length forest operations often rely on the use of brush mats created from harvesting debris (tree limbs, tops, and foliage) to reduce soil disturbances as a result of in-stand machine traffic. These brush mats, placed directly on the forest floor within machine operating trails, distribute loads of timber harvesting and extraction machinery to a greater area, thereby reducing peak pressures exerted to the ground and rutting for maintaining technical trafficability of operating trails. Forest biomass has also been promoted as a source of green and renewable energy, to reduce carbon emissions from energy production. However, to maintain sufficient quality of biomass for bioenergy operations (high heating value and low ash content), brush needs to be free of contaminants such as mineral soil. This constraint eliminates the possibility of the dual use of brush, first as a soil protective layer on machine operating trails and afterwards for bioenergy generation. Leaving machine operating trails uncovered will cause machine loads to be fully and directly applied to the soil, thus increasing the likelihood of severe soil disturbance, tree growth impediment and reducing trail trafficability. The main objective of this study was to quantify the effect of varying machine operating trail spacing and width on the amount of brush required for soil protection. This was achieved by creating five model forest stands (four mature and one immature), commonly found in New Brunswick, Canada, and using their characteristics as input in the Biomass Opportunity and Supply Model (BiOS) from FPInnovations. BiOS provided several key biomass related outputs allowing the determination of the amount of biomass available for soil protection, which was the main focus of this research. The simulation results showed that regardless of trail area tested, all four mature forest stands were able to support uniform distribution of 20 kg m−2 brush mats (green mass) throughout their entire trail network during clear-cut operations but not during partial harvests. From the three factors assessed (brush amount, trail width, and trail spacing), trail width had the highest effect on the required brush amount for trail protection, which in turn has a direct impact on the amount of brush that could be used for bioenergy generation
Influence of Saturated Organic Matter on the Accuracy of In-Situ Measurements Recorded with a Nuclear Moisture and Density Gauge
Full text linkThe impact of machines on forest soils is regularly assessed and quantified using absolute bulk density, which is most frequently obtained by soil cores. However, to allow for repeated measurements at the exact same locations, non-destructive devices are increasingly being used to determine soil bulk density and moisture content in field studies. An example of such a device is a nuclear moisture and density gauge (NMDG), originally designed as a control measurement for soil bulk density and moisture content in geotechnical applications. Unlike road construction or foundation projects that use mineral soil or gravel, forest soils have complex structures and the presence of organic matter, which can skew moisture and density readings from a NMDG. To gain further knowledge in this respect, we performed controlled tests in a sandbox to quantify the influence of varying amounts of saturated organic matter (3, 5, 10, and 15%) mixed with mineral soil in different layers (0–5, 0–10, 0–20 and 0–40 cm) on the accuracy of soil moisture content obtained by a NMDG and soil theta probe at varying depths. Main results illustrated that the presence of saturated organic matter per se was not problematic but moisture content overestimations and related underestimation of dry bulk density occurred when the tested measurement depth was below the created organic layer. Since forest soils often exhibit higher organic matter contents in the upper horizon, correction factors are suggested to minimize the moisture content variations between NMDG and reference method. With the use of correction factors, NMDG can present a non-destructive, fast, and accurate method of measuring soil moisture and bulk density in forestry applications
The role of brush mats in mitigating machine-induced soil disturbances: an assessment using absolute and relative soil bulk density and penetration resistance
No full textSoil displacement during ground-based mechanized forest operations using mixed-wood brush mats
No full textEffect of Season and Machine Type on Performance of Semi- and Fully Mechanized Harvesting Systems in Beech-Dominated Stands
Full text linkIt is common to have large trees in mature hardwood-dominated stands. This is especially true for European beech (Fagussylvatica L.), which can also have a complex architecture. Such trees have predominantly been harvested using motor-manual operations. However, in an effort to increase occupational safety and allow for a more continuous wood flow to processing facilities, fully-mechanized systems are also being employed more frequently. This study was established to determine the effect of season (Fall or Winter) and harvester type (wheeled or tracked) on the performance of semi- and fully- mechanized harvesting systems deployed in beech-dominated stands. Time-and-motion analysis was conducted on a total of 927 trees located in two forest sites in Germany. The study indicated that new silvicultural prescriptions make it impossible to harvest all trees exclusively with mechanized systems, even in the case of the tracked harvester with its 14.5 m boom. Motor-manual intervention was needed with trees that were too large, malformed or out of reach. Motor-manual intervention was significantly more frequent for the wheeled (30%) than for the tracked harvester (18%). Once again, tree size had the strongest effect on time consumption in a linear model, which varied from 0.5 to over 6 min per tree. Season and machine effect were also significant but could only account for a small fraction of the total variability. For the same tree size, time consumption was higher with the wheeled harvester and during the fall. The model also indicated a significant relationship between tree form and time consumption, even though the explanatory contribution of this independent variable was relatively small, too. Good stem form resulted in a lower time consumption. The larger tracked harvester was generally more efficient, but also more expensive to own and operate: its higher costs must be weighed against the higher revenues. New silvicultural trends make it difficult to achieve full mechanization, but the results of this study may guide managers towards technical solutions that minimize motor-manual intervention to the advantage of higher productivity and better occupational safety
Going Beyond Counting First Authors in Author Co-citation Analysis
Full text linkThe present study examines one of the fundamental aspects of author co-citation analysis (ACA) - the way co-citation
counts are defined. Co-citation counting provides the data on which all subsequent statistical analyses and mappings
are based, and we compare ACA results based on two different types of co-citation counting - the traditional type that
only counts the first one among a cited work's authors on the one hand and a non-traditional type that takes into
account the first 5 authors of a cited work on the other hand. Results indicate that the picture produced through this non-traditional author co-citation counting contains more coherent author groups and is therefore considerably clearer. However, this picture represents fewer specialties in the research field being studied than that produced through the traditional first-author co-citation counting when the same number of top-ranked authors is selected and analyzed. Reasons for these effects are discussed
Variations on the Author
Full text link“Variations on the Author” discusses two of Eduardo Coutinho’s recent films (Um Dia na Vida, from 2010, and Últimas Conversas, posthumously released in 2015) and their contribution to the general question of documentary authorship. The director’s filmography is characterized by a consistent yet self-effacing form of authorial self-inscription: Coutinho often features as an interviewer that rather than express opinions propels discourses; an interviewer that is good at listening. This mode of self-inscription characterizes him as an author who is not expressive but who is nonetheless markedly present on the screen. In Um Dia na Vida, however, Coutinho is completely absent form the image, while Últimas Conversas, on the contrary, includes a confessional prologue that moves the director from the margins to the center of his films. This article examines the ways in which these works stand out in the filmography of a director who offers new insights into the notion of cinematic authorship
Appropriate Similarity Measures for Author Cocitation Analysis
Full text linkWe provide a number of new insights into the methodological discussion about author cocitation analysis. We first argue that the use of the Pearson correlation for measuring the similarity between authors’ cocitation profiles is not very satisfactory. We then discuss what kind of similarity measures may be used as an alternative to the Pearson correlation. We consider three similarity measures in particular. One is the well-known cosine. The other two similarity measures have not been used before in the bibliometric literature. Finally, we show by means of an example that our findings have a high practical relevance.information science;Pearson correlation;cosine;similarity measure;author cocitation analysis
Dispelling the Myths Behind First-author Citation Counts
Full text linkWe conducted a full-scale evaluative citation analysis study of scholars in the XML research field to explore just how different from each other author rankings resulting from different citation counting methods actually are, and to demonstrate the capability of emerging data and tools on the Web in supporting more realistic citation counting methods. Our results contest some common arguments for the continued
use of first-author citation counts in the evaluation of scholars, such as high correlations between author rankings by first-author citation counts and other citation
counting methods, and high costs of using more realistic citation counting methods that are not well-supported by the ISI databases. It is argued that increasingly available digital full text research papers make it possible for citation analysis studies to go beyond what the ISI databases have directly supported and to employ more
sophisticated methods
- …
