1,720,958 research outputs found
Investigation Into Advanced Architecture and Strategies For Turbocharged Compressed Natural Gas Heavy Duty SI-engine
Get PDFCNG is at present retaining a growing interest as a factual alternative to traditional fuel for SI engine thanks to its high potentials in reducing the engine-out emissions. Increasing thrust into the exploitation of NG in the transport field is in fact produced by the even more stringent emission regulations which are being introduced into the worldwide scenario. Specific attention is also to be devoted to heavy duty engines given the high impact they retain due to the diesel oil exploitation and to the PM emissions, the latter issue assessing for the need to shift towards alternative fuels such as natural gas. A thorough control of the air-to-fuel ratio appears to be mandatory in spark ignition CNG engines in order to meet the even more stringent thresholds set by the current regulations. The accuracy of the air/fuel mixture highly depends on the injection system dynamic behavior and to its coupling to the engine fluid-dynamic. The amount of injected fuel should in fact be properly targeted by the ECU basing on the estimation of the induced air and accounting for the embedded closed-loop strategies. Still, these latter are normally derived from engine-base routines and totally ignore the injection system dynamics. Thus, a sound investigation into the mixing process can only be achieved provided that a proper analysis of the injection rail and of the injectors is carried out. The first part of the present work carries out a numerical investigation into the fluid dynamic behavior of a commercial CNG injection system by means of a 0D-1D code. The research has been focused on defining the set of parameters to be precisely reproduced in the 0D-1D simulation so as to match the injection system experimental behavior. Specific attention has been paid to the one component which significantly contributes to fully defining its dynamic response, i.e. the pressure reducing valve. The pressure reducer is made up of various elements that retain diverse weights on the valve behavior and should consequently be differently addressed to. A refined model of the pressure reducer has hence been proposed and the model has been calibrated, tested and run under various operating conditions so as to assess for the set-up validity. Comparisons have been carried out on steady state points as well as through out a vehicle driving cycle and the model capability to properly reproduce the real system characteristic has been investigated into. The proposed valve model has proved to consistently replicate the injection system response for different speed and load conditions. A few methodological indications concerning modeling aspects of a pressure regulator can be drawn from the present study. The model has been run in a predictive mode so as to inquiry into the response of the system to fast transient operations, both in terms of speed and load. The model outputs have highlighted mismatches between the ECU target mass and the actually injected one and have hinted at the need for dedicated and refined control strategies capable of preventing anomalies in the mixture formation and hence in the engine functioning. The second part of the present work aims at deeply investigating into the potentials of a heavy duty engine running on CNG and equipped with two different injection systems, an advanced SP one and a prototype MP one. The considered 7.8 liter engine was designed and produced to implement a Sigle-Point (SP) strategy and has hence been modified to run with a dedicated Multi-Point (MP) system so as to take advantage of its flexibility in terms of control strategies. More specifically, a thorough comparison between the experimental performances of the engine equipped with the two injection systems has been carried out at steady state as well as at transient operations. Better performances in terms of cycle-to-cycle variability were proved for the MP system despite poorer mixture homogeneity. Attention has also been paid to the different engine control strategies to be eventually adopted in compliance with the constraints set by the two different layouts. A 0D-1D model has also been built and validated on the experimental data set to be hence exploited for investigating into different strategies both for the SP and for the MP layout. An extensive simulation has been carried out on the effects of the injection phasing on the SP system performance referring to the engine power output and to the air-to-fuel ratio homogeneity amongst the cylinders. Finally, as far as the MP injection system is concerned, the innovative fire-skipping (DSF) or cylinder deactivation has been considered and deployed by means of the numerical model, assessing for an overall decrease in the fuel consumption of 12% at part load operations
Fluid-Dynamic Modeling and Advanced Control Strategies for a Gaseous-Fuel Injection System
No full textSustainable mobility has become a major issue for internal combustion engines and has led to increasing research efforts in the field of alternative fuels, such as bio-fuel, CNG and hydrogen addition, as well as into engine design and control optimization. To that end, a thorough control of the air-to-fuel ratio appears to be mandatory in SI engine in order to meet the even more stringent thresholds set by the current regulations. The accuracy of the air/fuel mixture highly depends on the injection system dynamic behavior and to its coupling to the engine fluid-dynamic. Thus, a sound investigation into the mixing process can only be achieved provided that a proper analysis of the injection rail and of the injectors is carried out.
The present paper carries out a numerical investigation into the fluid dynamic behavior of a commercial CNG injection system by means of a 0D-1D code. The model has been validated by comparing the experimental readings to the numerical outputs in terms of injection system pressure profiles versus time. The model has hence been applied to the prediction of the pressure waves produced by the injection event and of their effect on the actually injected fuel.
Experimental results have shown the effectiveness of the predictive model. A general good match between the predicted values and the measured rail pressure and injected fuel mass flow rates has been observed over a wide range of engine operation conditions. Moreover, the dynamic simulations have brought out a reduced independence of the injected fuel mass on the average rail pressure level, which further reduced for increasing engine power outputs. Moreover, the results have proved that the correct simulation of the system behavior relies on the consistent characterization of the pressure regulator functioning. It is worth observing that the full fluid dynamic characterization of the rail allows for the design of optimal control strategies so as to meet the engine requirements
Modelling aspects of a CNG injection system to predict its behavior under steady state conditions and throughout driving cycle simulations
No full textAlternative fuels such as compressed natural gas (CNG) have lately gained an increasing interest due to the even more stringent emission regulations and environmental policies. Considerable R&D activity has been carried out in order to enhance the mixture formation and to improve the after treatment efficiency. The achievement of these goals cannot disregard the importance of the injection system and of its component (common rail, injectors and pressure reducing valve) on the air-to-fuel mixing. The amount of injected fuel should in fact be properly targeted by the ECU basing on the estimation of the induced air and accounting for the embedded closed-loop strategies. Still, these latter are normally derived from engine-base routines and totally ignore the injection system dynamics.
The present paper aims at developing a thorough model of the injection system with specific attention to the one component which significantly contributes to fully defining its dynamic response, i.e. the pressure reducing valve. The pressure reducer is made up of various elements that retain diverse weights on the valve behavior and should consequently be differently addressed to. The research has been focused on defining the set of parameters to be precisely reproduced in the 0D-1D simulation so as to match the injection system experimental behavior. A refined model of the pressure reducer has hence been proposed and the model has been calibrated, tested and run under various operating conditions so as to assess for the set-up validity.
Comparisons have been carried out on steady state points as well as through out a vehicle driving cycle and the model capability to properly reproduce the real system characteristic has been investigated into. The proposed valve model has proved to consistently replicate the injection system response for different speed and load conditions. A few methodological indications concerning modeling aspects of a pressure regulator can be drawn from the present study.
Finally, the model has been run in a predictive mode so as to inquiry into the response of the system to fast transient operations, both in terms of speed and load. The model outputs have highlighted mismatches between the ECU target mass and the actually injected one and have hinted at the need for dedicated and refined control strategies capable of preventing anomalies in the mixture formation and hence in the engine functioning
Use of an Innovative Predictive Heat Release Model Combined to a 1D Fluid-Dynamic Model for the Simulation of a Heavy Duty Diesel Engine
No full textAn innovative 0D predictive combustion model for the simulation of the HRR (heat release rate) in DI diesel engines was assessed and implemented in a 1D fluid-dynamic commercial code for the simulation of a Fiat heavy duty diesel engine equipped with a Variable Geometry Turbocharger system, in the frame of the CORE (CO2 reduction for long distance transport) Collaborative Project of the European Community, VII FP. The 0D combustion approach starts from the calculation of the injection rate profile on the basis of the injected fuel quantities and on the injection parameters, such as the start of injection and the energizing time, taking the injector opening and closure delays into account. The injection rate profile in turn allows the released chemical energy to be estimated. The approach assumes that HRR is proportional to the energy associated with the accumulated fuel mass in the combustion chamber. This procedure allows an accurate calculation of different combustion parameters important for engine calibration, such as MFB50 (50% of fuel burned mass fraction crank angle)
Investigation into the Potentials of a Dedicated Multi-Point Injection System for a production NG Single-Point Heavy-Duty Engine
No full textCNG is at present retaining a growing interest as a factual alternative to traditional fuels for SI engines, thanks to its high potentials in reducing the engine-out emissions. Increasing thrust into the exploitation of NG in the transport field is in fact produced by the even more stringent emission regulations that are being introduced into the worldwide scenario. The present paper aims at deeply investigating into the potentials of a heavy-duty engine running on CNG and equipped with two different injection systems, an advanced single point (SP) one and a prototype multi-point (MP) one. The considered 7.8-liter engine was designed and produced to implement a SP strategy and hence modified to run with a dedicated MP system. A thorough comparison of the engine equipped with the two injection systems has been carried out at steady state as well as at transient operations. Better performances in terms of cycle-to-cycle variability were proved for the MP system despite poorer mixture homogeneity. A 0D-1D model has also been built and validated on the experimental data set to be hence exploited for investigating into different strategies both for the SP and for the MP layout. An extensive simulation has been carried out on the effects of the injection phasing on the SP system performance. Finally, as far as the MP injection system is concerned, the innovative fire-skipping or cylinder deactivation has been considered, assessing for an overall decrease in the fuel consumption of 12% at part load operations
Going Beyond Counting First Authors in Author Co-citation Analysis
Get PDFThe present study examines one of the fundamental aspects of author co-citation analysis (ACA) - the way co-citation
counts are defined. Co-citation counting provides the data on which all subsequent statistical analyses and mappings
are based, and we compare ACA results based on two different types of co-citation counting - the traditional type that
only counts the first one among a cited work's authors on the one hand and a non-traditional type that takes into
account the first 5 authors of a cited work on the other hand. Results indicate that the picture produced through this non-traditional author co-citation counting contains more coherent author groups and is therefore considerably clearer. However, this picture represents fewer specialties in the research field being studied than that produced through the traditional first-author co-citation counting when the same number of top-ranked authors is selected and analyzed. Reasons for these effects are discussed
Variations on the Author
Get PDF“Variations on the Author” discusses two of Eduardo Coutinho’s recent films (Um Dia na Vida, from 2010, and Últimas Conversas, posthumously released in 2015) and their contribution to the general question of documentary authorship. The director’s filmography is characterized by a consistent yet self-effacing form of authorial self-inscription: Coutinho often features as an interviewer that rather than express opinions propels discourses; an interviewer that is good at listening. This mode of self-inscription characterizes him as an author who is not expressive but who is nonetheless markedly present on the screen. In Um Dia na Vida, however, Coutinho is completely absent form the image, while Últimas Conversas, on the contrary, includes a confessional prologue that moves the director from the margins to the center of his films. This article examines the ways in which these works stand out in the filmography of a director who offers new insights into the notion of cinematic authorship
Appropriate Similarity Measures for Author Cocitation Analysis
Get PDFWe provide a number of new insights into the methodological discussion about author cocitation analysis. We first argue that the use of the Pearson correlation for measuring the similarity between authors’ cocitation profiles is not very satisfactory. We then discuss what kind of similarity measures may be used as an alternative to the Pearson correlation. We consider three similarity measures in particular. One is the well-known cosine. The other two similarity measures have not been used before in the bibliometric literature. Finally, we show by means of an example that our findings have a high practical relevance.information science;Pearson correlation;cosine;similarity measure;author cocitation analysis
Dispelling the Myths Behind First-author Citation Counts
Get PDFWe conducted a full-scale evaluative citation analysis study of scholars in the XML research field to explore just how different from each other author rankings resulting from different citation counting methods actually are, and to demonstrate the capability of emerging data and tools on the Web in supporting more realistic citation counting methods. Our results contest some common arguments for the continued
use of first-author citation counts in the evaluation of scholars, such as high correlations between author rankings by first-author citation counts and other citation
counting methods, and high costs of using more realistic citation counting methods that are not well-supported by the ISI databases. It is argued that increasingly available digital full text research papers make it possible for citation analysis studies to go beyond what the ISI databases have directly supported and to employ more
sophisticated methods
- …
