1,720,994 research outputs found
One-dimensional simulations and experimental analysis of a wastegated turbine for automotive engines under unsteady flow conditions
No full textIn the paper, the unsteady behaviour of a turbocharger waste-gated turbine (IHI-RHF3) is investigated following both an experimental and numerical approach. First, an experimental campaign is performed in a specialized test rig operating at the University of Genoa, for different openings of the waste-gate valve and under steady and unsteady flow operations. A proper configuration of the turbine outlet circuit fitted with a separating wall is used to carry out instantaneous measurements downstream the turbine wheel and the waste-gate valve.
The above data constitute the basis for the tuning and validation of a 1D turbine model, recently developed at the University of Naples. The procedure geometrically schematizes the entire turbine, starting from few linear and angular dimensions directly measured on the hardware. A preliminary model tuning is carried out on the basis of the characteristic map measured for a completely closed waste-gate valve under steady flow operations.
Then, a refined 1D schematization of the experimental apparatus is implemented within the commercial GT-Power® software, including the turbine, the waste-gate circuit and the upstream and downstream measuring stations. In particular, the classical map-based approach is suitably corrected with a sequence of pipes that schematizes each component of the turbine (inlet/outlet ducts, volute and wheel) to account for the wave propagation and storage phenomena inside the machine. A detailed 1D schematization of the waste-gate circuit is also implemented and independently tuned.
Finally, the turbine model capability under unsteady flow conditions is tested for different waste-gate openings and pulse frequencies, by applying time-dependent boundary conditions. In particular, the upstream and downstream measured pressure and temperature are imposed at the model ends, and the instantaneous mass flow rate and actual power are numerically evaluated. The results are compared with the experimental data, denoting a good accuracy, and showing some improvements with the respect to the standard turbine modelling in the case of the mass flow rate prediction. On the contrary, the computed actual power shows some inaccuracies, especially at higher pulse frequencies
Development of an Adaptive Efficient Thermal/Electric Skipping Control Strategy Applied to a Parallel Plug-in Hybrid Electric Vehicle
Full text linkIn recent years automobile manufacturers focused on an increasing degree of electrification of the powertrains with the aim to reduce pollutants and CO2 emissions. Despite more complex design processes and control strategies, these powertrains offer improved fuel exploitation compared to conventional vehicles thanks to intelligent energy management. A simulation study is here presented aiming at developing a new control strategy for a P3 parallel plug-in hybrid electric vehicle. The simulation model is implemented using vehicle modeling and simulation toolboxes in MATLAB/Simulink. The proposed control strategy is based on an alternative utilization of the electric motor and thermal engine to satisfy the vehicle power demand at the wheels (Efficient Thermal/Electric Skipping Strategy-ETESS). The choice between the two units is realized through a comparison between two equivalent fuel rates, one related to the thermal engine and the other related to the electric consumption. An adaptive function is introduced to develop a charge-blended control strategy. The novel adaptive control strategy (A-ETESS) is applied to estimate fuel consumption along different driving cycles. The control algorithm is implemented on a dedicated microcontroller unit performing a Processor-In-the-Loop (PIL) simulation. To demonstrate the reliability and effectiveness of the A-ETESS, the same adaptive function is built on the Equivalent Consumption Minimization Strategy (ECMS). The PIL results showed that the proposed strategy ensures a fuel economy similar to ECMS (worse of about 2% on average) and a computational effort reduced by 99% on average. This last feature reveals the potential for real-time on-vehicle applications
Vito De Bellis Politecnico di Bari, Italy, A Sport Park for the Foro Italico of Rome
No full textTesi di laurea, Facoltà di Architettura Politecnico di Bari, aa. 2008/2009 Coordinatore e Tutor: Anna Bruna Menghini.
Tesi di ricerca: "Il Foro Italico di Roma: la costruzione di un luogo tra monumento e organismo urbano"
Laboratorio di sintesi finale: "Il Foro Italico di Roma: riqualificazione architettonica, urbana e paesistica".
Presentato alla EAAE / ARCC International Conference on Architectural Research
Milano 7-10 June 2012
Tema 3
Criticism, Conservation and Restoration
Potential of hydrogen addition to natural gas or ammonia as a solution towards low- or zero-carbon fuel for the supply of a small turbocharged SI engine
Full text linkNowadays there is an increasing interest in carbon-free fuels such as ammonia and hydrogen. Those fuels, on one hand, allow to drastically reduce CO2 emissions, helping to comply with the increasingly stringent emission regulations, and, on the other hand, could lead to possible advantages in performances if blended with conventional fuels. In this regard, this work focuses on the 1D numerical study of an internal combustion engine supplied with different fuels: pure gasoline, and blends of methane-hydrogen and ammonia-hydrogen. The analyses are carried out with reference to a downsized turbocharged two-cylinder engine working in an operating point representative of engine operations along WLTC, namely 1800 rpm and 9.4 bar of BMEP. To evaluate the potential of methane-hydrogen and ammonia-hydrogen blends, a parametric study is performed. The varied parameters are air/fuel proportions (from 1 up to 2) and the hydrogen fraction over the total fuel. Hydrogen volume percentages up to 60% are considered both in the case of methane-hydrogen and ammonia-hydrogen blends. Model predictive capabilities are enhanced through a refined treatment of the laminar flame speed and chemistry of the end gas to improve the description of the combustion process and knock phenomenon, respectively. After the model validation under pure gasoline supply, numerical analyses allowed to estimate the benefits and drawbacks of considered alternative fuels in terms of efficiency, carbon monoxide, and pollutant emissions
CFD 3D Analysis of Charge Motion and Combustion in a Spark-Ignition Internal Combustion Engine under Close-to-Idle Condition
No full textThe increasingly stringent limitations on noxious missions of transport sector highly affect the development of new engines. The operating conditions of the engine at low-load and idle play a relevant role along the regulatory homologation cycles, contributing to overall emissions. In this work, the effectiveness of some solutions to improve the behaviour under close-to-idle operation of a Spark-Ignition motorcycle engine are compared by 3D CFD analyses. Specifically, the effects of two designs of the intake port and of the opening direction of the throttle valve, either clockwise or counterclockwise, are investigated. Multi-cycle simulations are carried out, under motored and fired conditions, for a single close-to-idle operating point. The various designs are compared in terms of capability to generate a stable tumble vortex during the intake phase and to produce an adequate turbulence level at the beginning of the combustion process. The analyses revealed that a clockwise throttle opening can produce enhanced turbulence levels at the end of the compression stroke, especially in a close-to-spark region (increase of about 5% and 27 % at the TDC at a global and local level, respectively, compared to the base configuration). Additional limited improvements are obtained with the high tumbling design, where, however, a penalty on the maximum power output could emerge. The flow and turbulence motion differences among the tested geometries reflect on combustion development in its early stage, and on its degree of completeness at the exhaust valve opening. A clockwise opening of the throttle valve leads to an increase of the mass fraction burned of 5 percent points, compared to the base configuration
Development of an efficient thermal electric skipping strategy for the management of a series/parallel hybrid powertrain
No full textIn recent years, the development of hybrid powertrain allowed to substantially reduce the CO2 and pollutant emissions of vehicles. The optimal management of such power units represents a challenging task since more degrees of freedom are available compared to a conventional pure-thermal engine powertrain. The a priori knowledge of the driving mission allows identifying the actual optimal control strategy at the expense of a quite relevant computational effort. This is realized by the off-line optimization strategies, such as Pontryagin minimum principle—PMP—or dynamic programming. On the other hand, for an on-vehicle application, the driving mission is unknown, and a certain performance degradation must be expected, depending on the degree of simplification and the computational burden of the adopted control strategy. This work is focused on the development of a simplified control strategy, labeled as efficient thermal electric skipping strategy—ETESS, which presents performance similar to off-line strategies, but with a much-reduced computational effort. This is based on the alternative vehicle driving by either thermal engine or electric unit (no power-split between the power units). The ETESS is tested in a “backward-facing” vehicle simulator referring to a segment C car, fitted with a hybrid series-parallel powertrain. The reliability of the method is verified along different driving cycles, sizing, and efficiency of the power unit components and assessed with conventional control strategies. The outcomes put into evidence that ETESS gives fuel consumption close to PMP strategy, with the advantage of a drastically reduced computational time. The ETESS is extended to an online implementation by introducing an adaptative factor, resulting in performance similar to the well-assessed equivalent consumption minimization strategy, preserving the computational effort
Efficient Thermal Electric Skipping Strategy Applied to the Control of Series/Parallel Hybrid Powertrain
Full text linkThe optimal control of hybrid powertrains represents one of the most challenging tasks for the compliance with the legislation concerning CO2 and pollutant emission of vehicles. Most common off-line optimization strategies (Pontryagin minimum principle-PMP-or dynamic programming) allow to identify the optimal control along a predefined driving mission at the expense of a quite relevant computational effort. On-line strategies, suitable for on-vehicle implementation, involve a certain performance degradation depending on their degree of simplification and computational effort. In this work, a simplified control strategy is presented, where the conventional power-split logics, typical of the above-mentioned strategies, is here replaced with an alternative utilization of the thermal and electric units for the vehicle driving (Efficient Thermal Electric Skipping Strategy-ETESS). The choice between the units is realized at each time and is based on the comparison between the effective fuel rate of the thermal engine and an equivalent fuel rate related to the electrical power consumption. The equivalent fuel rate in a pure electric driving is associated to a combination of brake specific fuel consumption of the thermal engine, and electro-mechanical efficiencies along the driveline. The ETESS is applied for the simulation of segment C hybrid vehicle, equipped with a thermal engine and two electric units (motor and generator). The methodology is tested along regulatory driving cycles (WLTP, Artemis) and RDE, with different powertrain variants. Numerical results underline that the proposed approach performs very close to most common control strategies (consumed fuel per kilometer higher than PMP of about 1% on average). The main advantage is a reduced computational effort (decrease of 99% on average). The ETESS is straightforwardly adapted for an on-line implementation, through the introduction of an adaptative factor, preserving the computational effort and the fuel economy
Hierarchical 1D/3D approach for the development of a turbulent combustion model applied to a VVA turbocharged engine. Part II: Combustion model
No full textAs discussed in the part I of this paper, 3D models represent a useful tool for a detailed description of the mean and turbulent flow fields inside the engine cylinder. 3D results are utilized to develop and validate a 0D phenomenological turbulence model, sensitive to the variation of operative parameters such as valve phasing, valve lift, engine speed, etc. In part II of this paper, a 0D phenomenological combustion model is presented, as well. It is based on a fractal description of the flame front and is able to sense each of the fuel properties, the operating conditions (air-to-fuel ratio, spark advance, boost level) and the combustion chamber geometry. In addition, it is capable to properly handle different turbulence levels predicted by means of the turbulence model presented in the part I. The turbulence and combustion models are included, through user routines, in the commercial software GT-Power". With reference to a small twin-cylinder VVA turbocharged engine, the turbulence/combustion model, once properly tuned, is finally used to calculate in-cylinder pressure traces, rate of heat release and overall engine performance at full load operations and brake specific fuel consumption at part load, as well. An excellent agreement between numerical forecasts and experimental evidence is obtained. © 2013 The Authors
Going Beyond Counting First Authors in Author Co-citation Analysis
Full text linkThe present study examines one of the fundamental aspects of author co-citation analysis (ACA) - the way co-citation
counts are defined. Co-citation counting provides the data on which all subsequent statistical analyses and mappings
are based, and we compare ACA results based on two different types of co-citation counting - the traditional type that
only counts the first one among a cited work's authors on the one hand and a non-traditional type that takes into
account the first 5 authors of a cited work on the other hand. Results indicate that the picture produced through this non-traditional author co-citation counting contains more coherent author groups and is therefore considerably clearer. However, this picture represents fewer specialties in the research field being studied than that produced through the traditional first-author co-citation counting when the same number of top-ranked authors is selected and analyzed. Reasons for these effects are discussed
- …
