255 research outputs found
Shock and spall behaviors of a high specific strength steel: Effects of impact stress and microstructure
Get PDFA series of plate-impact experiments were conducted to investigate the influences of impact stress and microstructure on the shock and spall behaviors of a high specific strength steel (HSSS). The HSSS shows a strong positive strain rate sensitivity on the yield strength. With increasing impact stress up to about 6 GPa the spall strength is found to decrease significantly and then levels off with further increasing impact stress. This trend is proposed to be attributed to the accumulation damage within the target as the initial shock-induced compression wave propagates through the target. The microcracks are clearly observed to nucleate from the interfaces between gamma-austenite and B2 phase and propagate along the interfaces or cut through the B2 phase in the HSSS during the spalling process. The Hugoniot elastic limit and the spall strength were found to be highly dependent on the microstructure. The spall strength was found to be higher when the density of the void nucleation sites is lower indicating that the spall strength should be a microstructure parameter of the HSSS under impact tensile conditions depending on the density of phase interfaces. It was also found that there is a tradeoff between the specific yield strength and the spall strength for this HSSS; thus the current findings should provide insights for achieving an optimal combination of both mechanical properties for impact-resistant applications by tailoring the microstructure. Published by AIP Publishing
Twin boundary spacing effects on shock response and spall behaviors of hierarchically nanotwinned fcc metals
No full textAtomistic deformation mechanisms of hierarchically nano-twinned (NT) Ag under shock conditions have been investigated using a series of large-scale molecular dynamics simulations. For the same grain size d and the same spacing of primary twins lambda(1), the average flow stress behind the shock front in hierarchically NT Ag first increases with decreasing spacing of secondary twins lambda(2), achieving a maximum at a critical lambda(2), and then drops as lambda(2) decreases further. Above the critical lambda(2), the deformation mechanisms are dominated by three type strengthening mechanisms: (a) partial dislocations emitted from grain boundaries (GBs) travel across other boundaries; (b) partial dislocations emitted from twin boundaries (TBs) travel across other TBs; (c) formation of tertiary twins. Below the critical lambda(2), the deformation mechanism are dominated by two softening mechanisms: (a) detwinning of secondary twins; (b) formation of new grains by cross slip of partial dislocations. Moreover, the twin-free nanocrystalline (NC) Ag is found to have lower average flow stress behind the shock front than those of all hierarchically NT Ag samples except the one with the smallest lambda(2) of 0.71 nm. No apparent correlation between the spall strength and lambda(2) is observed in hierarchically NT Ag, since voids always nucleate at both GBs and boundaries of the primary twins. However, twin-free NC Ag is found to have higher spall strength than hierarchically NT Ag. Voids can only nucleate from GBs for twin-free NC Ag, therefore, twin-free NC Ag has less nucleation sources along the shock direction when compared to hierarchically NT Ag, which requiring higher tensile stress to create spallation. These findings should contribute to the understandings of deformation mechanisms of hierarchically NT fcc metals under extreme deformation conditions. (C) 2014 AIP Publishing LLC
Investigation of structural-scale levels of spall fracture induced by a nanosecond relativistic high-current electron beam in ultrafine-grained Ti–Al–V–Mo alloy
Get PDFThe results of an experimental and theoretical study of shock-wave processes and spall fracture in an ultrafine-grained and coarse-grained (α + β) Ti–Al–V–Mo alloy under the action of a nanosecond relativistic high-current electron beam are reported. Mathematical modeling is performed to show that when an electron beam with a power density of 1.65 × 1010 W/cm2 impacts this alloy, a shock wave with a compression amplitude of 13 GPa appears and its reflection gives rise to a tensile wave. Its amplitude increases with decreasing target thickness. The calculated increase in the thickness of the spalled layer at the rear surface of the target corresponds to the experimental data. It is established experimentally that plastic deformation precedes the spall fracture sequentially at three structural-scale levels. At the beginning pores are formed and merge, then microcracks are formed at different angles to the back surface of the target between the pores, and then a macrocrack is formed. As a result, the macrocrack surface is not smooth but exhibits pits of ductile fracture
Spall damage in aluminum-alloy
No full textA void growth relations for ductile porous materials under intense dynamic general loading condition is presented. The mathematical model includes the influence of inertial effects, material rate sensitivity, as well as the contribution of void surface energy and material work-hardening. Numerical analysis shows that inertia appears to resist the growth of voids. The inertial effects increase quickly with the loading rates. The theoretical analysis suggests that the inertial effects cannot be neglected at high loading rates. Plate-impact tests of aluminum alloy are performed with light gas gun. The processes of dynamic damage in aluminum alloy are successfully simulated with a finite-difference dynamic code in which the theoretical model presented in this paper is incorporated
Improved CE/SE scheme with particle level set method for numerical simulation of spall fracture due to high-velocity impact
No full textIn the present paper, an Eulerian scheme combined with the hybrid particle level set method for numerical simulation of spall fracture due to high-velocity impact is proposed. An axisymmetric framework is established, based on an improved CE/SE scheme, to solve the high-velocity impact problems with large deformations, high strain rates and spall fractures. The hybrid particle level set method is adopted for tracking material interfaces and describing the formation and propagation of a crack. A novel representation of crack by level set is proposed. Numerical simulations are carried out and compared to the corresponding experimental results. The numerical results are in good agreement with the experimental data. The edge effects are reproduced and the decrease of scab thickness with increase in impact velocity is observed owing to the numerical analysis. It is proved that our computational technique is feasible and reliable for analyzing the spall fracture. (C) 2010 Elsevier Inc. All rights reserved.Computer Science, Interdisciplinary ApplicationsPhysics, MathematicalSCI(E)10ARTICLE197503-751922
Corrigendum
Get PDFAuthor Posting. © American Meteorological Society, 2010. This article is posted here by permission of American Meteorological Society for personal use, not for redistribution. The definitive version was published in Journal of Physical Oceanography 40 (2010): 1910–1914, doi:10.1175/2010JPO4483.1.Corrigendum: Spall, M. A., R. S. Pickart, P. S. Fratantoni, and A. J. Plueddemann, 2008: Western Arctic shelfbreak eddies:
Formation and transport. J. Phys. Oceanogr., 38, 1644–166
Hidden Upwelling Systems Associated With Major Western Boundary Currents
Get PDF© The Author(s), 2022. This article is distributed under the terms of the Creative Commons Attribution License. The definitive version was published in Liao, F., Liang, X., Li, Y., & Spall, M. Hidden upwelling systems associated with major western boundary currents. Journal of Geophysical Research: Oceans. 127, (2022): e2021JC017649, https://doi.org/10.1029/2021jc017649.Western boundary currents (WBCs) play an essential role in regulating global climate. In contrast to their widely examined horizontal motions, less attention has been paid to vertical motions associated with WBCs. Here, we examine vertical motions associated with the major WBCs by analyzing vertical velocity from five ocean synthesis products and one eddy-resolving ocean simulation. These data reveal robust and intense subsurface upwelling systems, which are primarily along isopycnal surfaces, in five major subtropical WBC systems. These upwelling systems are part of basin-scale overturning circulations and are likely driven by meridional pressure gradients along the western boundary. Globally, the WBC upwelling contributes significantly to the vertical transport of water mass and ocean properties and is an essential yet overlooked branch of the global ocean circulation. In addition, the WBC upwelling intersects the oceanic euphotic and mixed layers, and thus likely plays an important role in ocean biological and chemical processes by transporting nutrients, carbon and other tracers vertically inside the ocean. This study calls for more research into the dynamics of the WBC upwelling and their role in the ocean and climate systems.X. Liang is supported by the National Science Foundation through Grants OCE-2021274, OCE-2122507, and the Alfred P. Sloan Foundation through Grant FG-2019-12536. M. Spall is supported through the National Science Foundation Grants OCE-1947290 and OCE-2122633
Three Dimensional Characterization of Microstructural Effects on Spall Damage in Shocked Polycrystalline Copper
Get PDFabstract: Shock loading is a complex phenomenon that can lead to failure mechanisms such as strain localization, void nucleation and growth, and eventually spall fracture. The length scale of damage with respect to that of the surrounding microstructure has proven to be a key aspect in determining sites of failure initiation. Studying incipient stages of spall damage is of paramount importance to accurately determine initiation sites in the material microstructure where damage will nucleate and grow and to formulate continuum models that account for the variability of the damage process due to microstructural heterogeneity, which is the focus of this research. Shock loading experiments were conducted via flyer-plate impact tests for pressures of 2-6 GPa and strain rates of 105/s on copper polycrystals of varying thermomechanical processing conditions. Serial cross sectioning of recovered target disks was performed along with electron microscopy, electron backscattering diffraction (EBSD), focused ion beam (FIB) milling, and 3-D X-ray tomogrpahy (XRT) to gain 2-D and 3-D information on the spall plane and surrounding microstructure. Statistics on grain boundaries (GB) containing damage were obtained from 2-D data and GBs of misorientations 25° and 50° were found to have the highest probability to contain damage in as-received (AR), heat treated (HT), and fully recrystallized (FR) microstructures, while {111} Σ3 GBs were globally strong. The AR microstructure’s probability peak was the most pronounced indicating GB strength is the dominant factor for damage nucleation. 3-D XRT data was used to digitally render the spall planes of the AR, HT, and FR microstructures. From shape fitting the voids to ellipsoids, it was found that the AR microstructure contained greater than 55% intergranular damage, whereas the HT and FR microstructures contained predominantly transgranular and coalesced damage modes, respectively. 3-D reconstructions of large volume damage sites in shocked Cu multicrystals showed preference for damage nucleation at GBs between adjacent grains of a high Taylor factor mismatches as well as an angle between the shock direction and the GB physical normal of ~30°-45°. 3-D FIB sectioning of individual voids led to the discovery of uniform plastic zones ~25-50% the size of the void diameter and plastic deformation directions were characterized via local average misorientation maps. Incipient transgranular voids revealed from the sectioning process were present in grains of high Taylor factors along the shock direction, which is expected as materials with a low Taylor factor along the shock direction are susceptible to growth due their accomodation of plastic deformation. Fabrication of square waves using photolithography and chemical etching was developed to study the nature of plasticity at GBs away from the spall plane. Grains oriented close to had half the residual amplitudes than grains oriented close to .Dissertation/ThesisDoctoral Dissertation Mechanical Engineering 201
Revisiting concrete frost salt scaling: On the role of the frozen salt solution micro-structure
No full textWe simulate the glue-spall stress due to mechanical interactions between a frozen saline solution (brine-ice composite) and a non-air entrained concrete surface including the impact of the micro-structure of the frozen solution. The presence of brine channels at the ice/concrete interface was found to be a prerequisite to induce stress during freezing and hence for scaling to occur. Pure ice does not result in scaling as it does not have brine channels. Furthermore, the size of the brine channels and their distribution was found determinant for the magnitude of the glue-spall stress in the concrete and the experimentally observed pessimum effect of a medium salt concentration was explained based on the change of the microstructure of the brine-ice composite at different salt concentrations and temperatures. The predicted results are in good agreement with the experimental observations and the few numerical demonstrations related to frost salt scaling in the literature.Green Open Access added to TU Delft Institutional Repository ‘You share, we take care!’ – Taverne project https://www.openaccess.nl/en/you-share-we-take-care Otherwise as indicated in the copyright section: the publisher is the copyright holder of this work and the author uses the Dutch legislation to make this work public.Concrete Structure
The effect of loading direction on the dynamic damage in lean duplex stainless steel 2101
No full text© 2018 Author(s). The effect of loading direction on the spall strength and damage in Lean Duplex Stainless Steel 2101 (LDSS 2101) has been investigated. Experiments were conducted in a single stage gas-gun to test the spall strength of LDSS 2101 along the Rolling Direction (RD), Transverse Direction (TD) and Normal Direction (ND). Microstructural examinations were conducted using optical microscopy and Electron Backscatter Diffraction (EBSD). LDSS 2101 showed similar spall strength in all considered directions. However, the amount of spall damage was dependent on the loading direction. Moreover, most of the spall damage was accommodated within the ferrite phase
- …
