1,721,059 research outputs found
Comb-drives: Versatile micro-structures for capacitive sensing and electrostatic actuation
Full text linkA comb-drive is a structure of interdigitated conductive fingers from which one part is able to move. Electrostatic forces allow the structure to function as an actuator whereas capacitance changes give way to use the structure as a sensor. Such structures became feasible on micrometer scale with the advent of surface micromachining in the late eighties. Since then there has been an overwhelming number of applications of comb-drives both in micro-actuation and sensing. This paper gives an overview of the basic operation of a comb-drive and its applications in sensing and actuation
Mode hop free single mode fibre ring laser with frequency scanning using a fibre ring resonator filter combined with Mach-Zehnder interferometer
No full textFibre‐Optic Sensing
No full textThis chapter reflects upon the past and on the achievements that fibre sensors have made over the past half-century. It explains the simple observation that market presence of fibre-optic sensing is modest at best. The chapter illustrates the essentials of a photonic system. Photonics as a discipline is most certainly arousing strategic interest with targeted research and development programmes emerging in both the United States and the European Union. The microstructured fibres, also known as photonic crystal fibres, dramatically increased the variety of geometries and optical responses available to fibre-based sensing. These fibres have arrays of wavelength-scale air holes in their transverse cross section, which extend along the full fibre length and define the waveguide properties. Fibre-optic sensing will continue to provide not only exciting research opportunities but also intriguing (and profitable) application niches in the future
Going Beyond Counting First Authors in Author Co-citation Analysis
Full text linkThe present study examines one of the fundamental aspects of author co-citation analysis (ACA) - the way co-citation
counts are defined. Co-citation counting provides the data on which all subsequent statistical analyses and mappings
are based, and we compare ACA results based on two different types of co-citation counting - the traditional type that
only counts the first one among a cited work's authors on the one hand and a non-traditional type that takes into
account the first 5 authors of a cited work on the other hand. Results indicate that the picture produced through this non-traditional author co-citation counting contains more coherent author groups and is therefore considerably clearer. However, this picture represents fewer specialties in the research field being studied than that produced through the traditional first-author co-citation counting when the same number of top-ranked authors is selected and analyzed. Reasons for these effects are discussed
Variations on the Author
Full text link“Variations on the Author” discusses two of Eduardo Coutinho’s recent films (Um Dia na Vida, from 2010, and Últimas Conversas, posthumously released in 2015) and their contribution to the general question of documentary authorship. The director’s filmography is characterized by a consistent yet self-effacing form of authorial self-inscription: Coutinho often features as an interviewer that rather than express opinions propels discourses; an interviewer that is good at listening. This mode of self-inscription characterizes him as an author who is not expressive but who is nonetheless markedly present on the screen. In Um Dia na Vida, however, Coutinho is completely absent form the image, while Últimas Conversas, on the contrary, includes a confessional prologue that moves the director from the margins to the center of his films. This article examines the ways in which these works stand out in the filmography of a director who offers new insights into the notion of cinematic authorship
Appropriate Similarity Measures for Author Cocitation Analysis
Full text linkWe provide a number of new insights into the methodological discussion about author cocitation analysis. We first argue that the use of the Pearson correlation for measuring the similarity between authors’ cocitation profiles is not very satisfactory. We then discuss what kind of similarity measures may be used as an alternative to the Pearson correlation. We consider three similarity measures in particular. One is the well-known cosine. The other two similarity measures have not been used before in the bibliometric literature. Finally, we show by means of an example that our findings have a high practical relevance.information science;Pearson correlation;cosine;similarity measure;author cocitation analysis
Development of active materials with adaptive acoustic impedance
No full textActive materials with adaptive acoustic impedance are materials with an acoustic characteristic which can be controlled using as external source of energy and a control circuit. Controlling the acoustic impedance means controlling the transmission, reflection and absorption properties of the material.IE
Dispelling the Myths Behind First-author Citation Counts
Full text linkWe conducted a full-scale evaluative citation analysis study of scholars in the XML research field to explore just how different from each other author rankings resulting from different citation counting methods actually are, and to demonstrate the capability of emerging data and tools on the Web in supporting more realistic citation counting methods. Our results contest some common arguments for the continued
use of first-author citation counts in the evaluation of scholars, such as high correlations between author rankings by first-author citation counts and other citation
counting methods, and high costs of using more realistic citation counting methods that are not well-supported by the ISI databases. It is argued that increasingly available digital full text research papers make it possible for citation analysis studies to go beyond what the ISI databases have directly supported and to employ more
sophisticated methods
Structural monitoring with fibre-optic sensors using the pulsed time-of-flight method and other measurement techniques
Full text linkAbstractThis thesis deals with the developing of fibre-optic instruments for monitoring the health of civil engineering and composite structures. A number of sensors have been tested for use with different road structures, concrete bridges, fibre reinforced polymer (FRP) containers and other composite specimens, the interrogation methods being mainly based on measuring optical power and time-of-flight (TOF). The main focus is on the development of a fibre-optic TOF measurement system and its applications, but different sensing needs and fibre-optic measurement systems are also reviewed, with the emphasis on commercial devices. Deformation in a road structure was studied with microbending sensors of gauge-length about 10 cm and a commercial optical time domain reflectometer (OTDR) in a quasi-distributed fashion. The responses of the optical fibre sensors during the one-year measurement period were similar in shape to those obtained with commercial strain gauges but the absolute measurement values typically deviated by several tens of per cent. Low dynamic range, crosstalk and poor signal-to-noise ratio proved to be the main problem when measuring several successive sensors with an OTDR. In another road investigation, microbending and speckle sensors were found useful for providing on/off-type information for traffic control applications. FRP composite containers were investigated with the focus on developing a continuous monitoring system for improving yield and quality by evaluating the state of cure during the manufacturing process and for assessing damage, e.g. delaminations, during service life. Standard multi-mode and single mode fibres with a typical length of a few hundreds of metres were embedded inside the walls of containers during the normal manufacturing process, and the measurements were carried out using an optical through-power technique and an OTDR. This largely empirical investigation revealed that the coating material and its thickness have an effect on loading sensitivity and on the applicability of the method for cure monitoring. The measurement data also indicated that the end-of-curing process and the location of external damage can be determined with a distributed optical fibre sensor and an OTDR. Several versions of a pulsed time-of-flight measurement system were developed for interrogating sensor arrays consisting of multiple long gauge-length sensors. The early versions based on commercial electronics were capable of producing relevant measurement data with a reasonable precision, but they suffered especially from poor spatial resolution, low sampling rate and long-term drift.The high precision TOF system developed in this thesis is capable of measuring time delays between a number of wideband reflectors, such as connectors or fibre Bragg gratings (FBG), along a fibre path with a precision of about 280 fs (rms-value) and a spatial resolution of about 3 ns (0.30 m) in a measurement time of 25 milliseconds. By using a fibre loop sensor with a reference fibre, a strain precision below 1 με and a measurement frequency of 4 Hz can be achieved. The system has proved comparable in performance to a commercial FBG interrogation system in monitoring the behaviour of a bridge deck, while the fact that it allows static and dynamic measurements with a number of long gauge-length sensors, also embedded in FRP composite material, makes this TOF device unique relative to other measurement systems. Academic dissertation to be presented, with the assent of the Faculty of Technology of the University of Oulu, for public defence in Keckmaninsali (Auditorium HU106), Linnanmaa, on January 25th, 2008, at 12 noonAbstract
This thesis deals with the developing of fibre-optic instruments for monitoring the health of civil engineering and composite structures. A number of sensors have been tested for use with different road structures, concrete bridges, fibre reinforced polymer (FRP) containers and other composite specimens, the interrogation methods being mainly based on measuring optical power and time-of-flight (TOF). The main focus is on the development of a fibre-optic TOF measurement system and its applications, but different sensing needs and fibre-optic measurement systems are also reviewed, with the emphasis on commercial devices.
Deformation in a road structure was studied with microbending sensors of gauge-length about 10 cm and a commercial optical time domain reflectometer (OTDR) in a quasi-distributed fashion. The responses of the optical fibre sensors during the one-year measurement period were similar in shape to those obtained with commercial strain gauges but the absolute measurement values typically deviated by several tens of per cent. Low dynamic range, crosstalk and poor signal-to-noise ratio proved to be the main problem when measuring several successive sensors with an OTDR. In another road investigation, microbending and speckle sensors were found useful for providing on/off-type information for traffic control applications.
FRP composite containers were investigated with the focus on developing a continuous monitoring system for improving yield and quality by evaluating the state of cure during the manufacturing process and for assessing damage, e.g. delaminations, during service life. Standard multi-mode and single mode fibres with a typical length of a few hundreds of metres were embedded inside the walls of containers during the normal manufacturing process, and the measurements were carried out using an optical through-power technique and an OTDR. This largely empirical investigation revealed that the coating material and its thickness have an effect on loading sensitivity and on the applicability of the method for cure monitoring. The measurement data also indicated that the end-of-curing process and the location of external damage can be determined with a distributed optical fibre sensor and an OTDR.
Several versions of a pulsed time-of-flight measurement system were developed for interrogating sensor arrays consisting of multiple long gauge-length sensors. The early versions based on commercial electronics were capable of producing relevant measurement data with a reasonable precision, but they suffered especially from poor spatial resolution, low sampling rate and long-term drift.
The high precision TOF system developed in this thesis is capable of measuring time delays between a number of wideband reflectors, such as connectors or fibre Bragg gratings (FBG), along a fibre path with a precision of about 280 fs (rms-value) and a spatial resolution of about 3 ns (0.30 m) in a measurement time of 25 milliseconds. By using a fibre loop sensor with a reference fibre, a strain precision below 1 με and a measurement frequency of 4 Hz can be achieved. The system has proved comparable in performance to a commercial FBG interrogation system in monitoring the behaviour of a bridge deck, while the fact that it allows static and dynamic measurements with a number of long gauge-length sensors, also embedded in FRP composite material, makes this TOF device unique relative to other measurement systems
- …
