130,598 research outputs found
Development of a Robotics-based Satellites Docking Simulator
No full textThe European Proximity Operation Simulator (EPOS) is a hardware-in-the-loop (HIL) system aiming, among other objectives, at emulating on-orbit docking of spacecraft for verification and validation of the docking phase. This HIL docking simulator set-up essentially consists of docking interfaces, simulating the servicing satellite called chaser satellite, the serviced satellite called target satellite, a sensor of the forces and torques during contact, and two industrial robots that hold the docking interfaces, and control satellites motion relative position and attitude. Furthermore, the EPOS includes a real-time controller interface linked to a computer-based numerical simulator of satellites orbital and attitude dynamics. A key feature of this set-up is the feedback loop that is closed on the real force sensed at the docking interfaces during contact. That feedback force is used as driving input to satellites dynamics numerical simulation. This HIL docking simulation concept has the unique advantage of using the measured contact forces and torques, but it presents significant challenges. The high stiffness of the industrial robots and the docking interfaces yields a high bandwidth contact dynamics at impact and, thus, very short contact time durations. These times might be shorter than the inherent time delay of the robot controllers. This leads to physical inconsistency in the docking dynamics and measured variables. This also causes a stability issue in the force feedback HIL system during contact and may cause catastrophic damages to the robots. Additional problems that need to be addressed are the characterization of the stability domain of operation, the compensation of the non-contact forces and torques, such as the measured forces and torques due to gravity effect. Finally, this thesis addresses the task of identifying the dynamic behavior of the robot end-effectors. This thesis addresses the above mentioned challenges and problems and presents solutions towards a stable and safe docking simulation operation of the EPOS facility. First, in order to mitigate the high stiffness and time delay problem, the thesis introduces a novel idea of simulating contact based on a concept called hybrid contact dynamics model. The method, developed in this thesis, is based on a combination of a passive compliance control introduced at the end-effector of the robot and a virtual contact model. The virtual contact model allows the operator to vary the contact parameters which can also be used as a control gain. The method also allows to solve the stability problem coming from the combination of time delay of the robot controller and high stiffness of the robot end-effector. For the passive compliance control, a new device is designed that has fairly known stiffness properties which are softer than the robot and docking interface stiffness. Second, the thesis presents a stability analysis of the proposed method via the adaptation of the pole location method to dead-time systems. The analysis is based on a linearized design model of the dynamics; linearization is performed around the docking geometrical configuration. This work first presents an analysis for the single dimensional case, which is then extended to two dimensions. The highlight of the stability analysis is the development of physically intuitive state-space model that easily unveil the modes of the contact dynamics. The application of the pole location method to the resulting second-order characteristics polynomial is straight forward. The contribution of this analysis is a closed-form relationship, and associated plots, among the system's parameter, i.e., the satellite's masses, the stiffness and damping coefficient of the contact parameters, the delay, and the geometry. In addition, the stability analysis is supported using the passivity method which is valid for three dimensions. Third, a model of the force-torque sensor is presented, and the classical weighted least-squares estimation technique is suggested for the identification and compensation of the non-contact forces and torques from the contact force and the torque measurement. Finally, it is proposed to utilize a LEICA laser tracker, a positioning measurement system, in order to identify the robot end-effectors dynamics behaviors such as the natural frequency and damping ratio. This hybrid contact dynamics model and the accompanying analysis is envisioned as a tool for safe and flexible EPOS operations. This tool shall allow emulation of the desired impact dynamics for any stiffness and damping characteristics within the stability region without recurring to a modification of the hardware. The experimental results of the robotics based hybrid docking simulator comply with experimental data from an air-bearing testbed that was independently performed by this author at the Space Robotics Laboratory of Tohoku University. It demonstrates the validity of the novel EPOS concept of operations and increases the confidence of using this approach for future on-orbit docking/contact algorithm validation, at the EPOS facility.Space Systems EngineeringAerospace Engineerin
Two neglected biologic risk factors in bone grafting and implantology: high low-density lipoprotein cholesterol and low serum vitamin D.
No full textMeSH term explosion and author rank improve expert recommendations
No full textInformation overload is an often-cited phenomenon that reduces the productivity, efficiency and efficacy of scientists. One challenge for scientists is to find appropriate collaborators in their research. The literature describes various solutions to the problem of expertise location, but most current approaches do not appear to be very suitable for expert recommendations in biomedical research. In this study, we present the development and initial evaluation of a vector space model-based algorithm to calculate researcher similarity using four inputs: 1) MeSH terms of publications; 2) MeSH terms and author rank; 3) exploded MeSH terms; and 4) exploded MeSH terms and author rank. We developed and evaluated the algorithm using a data set of 17,525 authors and their 22,542 papers. On average, our algorithms correctly predicted 2.5 of the top 5/10 coauthors of individual scientists. Exploded MeSH and author rank outperformed all other algorithms in accuracy, followed closely by MeSH and author rank. Our results show that the accuracy of MeSH term-based matching can be enhanced with other metadata such as author rank
Going Beyond Counting First Authors in Author Co-citation Analysis
No full textThe present study examines one of the fundamental aspects of author co-citation analysis (ACA) - the way co-citation
counts are defined. Co-citation counting provides the data on which all subsequent statistical analyses and mappings
are based, and we compare ACA results based on two different types of co-citation counting - the traditional type that
only counts the first one among a cited work's authors on the one hand and a non-traditional type that takes into
account the first 5 authors of a cited work on the other hand. Results indicate that the picture produced through this non-traditional author co-citation counting contains more coherent author groups and is therefore considerably clearer. However, this picture represents fewer specialties in the research field being studied than that produced through the traditional first-author co-citation counting when the same number of top-ranked authors is selected and analyzed. Reasons for these effects are discussed
Relative Navigation in Asteroid Missions: Dual Quaternion Approach
No full textAerospace EngineeringSpace EngineeringAstrodynamics & Space Mission
"Closing the R&D Gap, Evaluating the Sources of R&D Spending"
No full textBoth spending and tax policies have been implemented in the United States with the goal of stimulating private sector research and development (R&D). Karier questions whether current R&D policy, especially the research and experimentation tax credit, can contribute to closing the gap between nondefense expenditures on R&D in the United States and such expenditures in other countries, such as Japan and Germany. He also explores possible changes to our current R&D policy to make it more effective.
Dispelling the Myths Behind First-author Citation Counts
No full textWe conducted a full-scale evaluative citation analysis study of scholars in the XML research field to explore just how different from each other author rankings resulting from different citation counting methods actually are, and to demonstrate the capability of emerging data and tools on the Web in supporting more realistic citation counting methods. Our results contest some common arguments for the continued
use of first-author citation counts in the evaluation of scholars, such as high correlations between author rankings by first-author citation counts and other citation
counting methods, and high costs of using more realistic citation counting methods that are not well-supported by the ISI databases. It is argued that increasingly available digital full text research papers make it possible for citation analysis studies to go beyond what the ISI databases have directly supported and to employ more
sophisticated methods
- …
