Scipedia
Not a member yet
33380 research outputs found
Sort by
Ambient Seismic Noise Imaging for Tailings Storage Facilities Monitoring: a Benchmark between Accelerometers and DAS
Get PDFRecent examples of tailings dam failure remind us how the monitoring of such sites is important. One major factor affecting the stability of tailings storage facilities (TSFs) is the presence and movement of water within the facility. Dam failures are often caused by seepage or the presence of weak layers within the tailings dam or the foundation soil. Thus, monitoring for the presence or movement of water within TSFs is becoming increasingly important, and solutions for permanent, non-intrusive and cost-effective monitoring of dams are a major challenge. One such solution is represented by geophysical imaging techniques such as ambient seismic noise interferometry. Through a research project, a nodal network system of accelerometer sensors was installed in a dense and random array on a TSF embankment wall at an Australian mine. Simultaneously, a fiber optic cable was deployed in a trench at the top of the TSF. Ambient seismic noise was recorded over a few weeks using the nodal network and with the fiber optic cable over several months using Distributed Acoustic Sensing (DAS) technology. Following data acquisition, benchmarking passive seismic imaging from the accelerometer network and the DAS system was conducted to evaluate the DAS capabilities for long-term TSF monitoring
Delivery added value using field measurements through the application of the Observational Method
Get PDFHigh Speed Two (HS2) is the new high-speed railway line in the UK currently being constructed between London and Birmingham. The designs of many HS2 retaining structures, as can be the case for some projects in the UK, were progressed concurrently with ground investigation. In this situation, to manage uncertainties in the ground, a cautious assessment of ground parameters was usually adopted. The purpose of field monitoring varies depending on the responsible or interested party. For designers, the primary aim is usually for design verification of their permanent works design. This paper describes how field observations, particularly quality instrumentation and monitoring data, were used at HS2 Bromford Tunnel East Portal to improve the existing design as construction progressed to create savings. To improve the efficiency in data processing, DAARWIN, a machine learning-based technology was used. The design and construction of the eastern end of the Bromford Tunnel East Portal were modified by eliminating the requirements of temporary support using measured field data, site observations and a carefully controlled construction through the application of the Observational Method. The portal construction programme was shortened by at least two weeks despite only three of the remaining temporary steel props being omitted. The findings revealed opportunities to extend the application of the Observational Method on adjacent structures including Bromford Tunnel West Portal and Washwood Heath Retained Cut. Given the great length of retained excavations of the two structures, the potential efficiency gains in cost, time and carbon emissions are significant whilst enhancing safety
Monitoring of Tunnels in Urban Environments Complementing InSAR with in-situ Ground Instrumentation
Get PDFOne of the challenges in urban tunnelling projects is to guarantee that the infrastructure assets crossing or adjacent to the tunnel alignment and other new build elements are not affected by the construction activity. Radar Satellite Interferometry (InSAR) is a non-invasive surveying technique which provides millimetric deformation measurements of terrain structures over wide areas without any need to access site. This technique allows a comprehensive and periodic vision, with the same accuracy as manual levelling in cities for a fraction of the cost of traditional systems. ATLAS is the Sixense’s InSAR processing chain, aimed to monitor the different tunnelling activities phases: access shaft excavation, tunnel construction and settlement. This study focuses on real data obtained by Sixense during the monitoring of urban tunnel construction work in three major projects in London (UK) and Porto (Portugal), using a combination of technologies: InSAR for remote monitoring and two topographic instrumentation methods: Topographic Control Prisms through measurements with Robotic Total Station and Topographic Levelling. The methodology employed integrated InSAR to obtain surface deformation data across the tunnel influence zone and on-site instrumentation for detailed and precise measurements. Its implementation enabled continuous monitoring, revealing accurate and real-time deformation patterns near the tunnels. The results demonstrated a significant correlation between InSAR data and on-site measurements, validating the effectiveness of this combination
Effects of Vane Size and Aspect Ratio on the Measurement of Undrained Shear Strength of a Fine-Grained Soil
Get PDFThe field Vane Shear Test (VST) is a widely used in-situ test method to measure undrained shear strength and sensitivity of saturated, fine-grained soils. The United States Bureau of Reclamation (Reclamation) commonly performs this test method to help inform numerical modeling of earth embankment dams when undergoing a risk analysis or design. Although the test method itself has been a geotechnical tool for quite some time, its primary use has traditionally been limited to sites with soft and/or relatively shallow clay soil. Typically, embankment and foundation materials of interest at Reclamation facilities are at greater depths, under higher effective stresses, and can be relatively stiff. Testing of stronger soils poses issues when performing the VST; typical commercially available equipment has a limited torque capacity to cause yielding of the soil. As a solution, modifying the dimensions and aspect ratio of the vane is an economic means of increasing the measurable range of undrained strength. Yet, the effects of these modifications are not well understood. Soil strength anisotropy is one of the primary components of this uncertainty. Testing on a sandy lean clay has been conducted to enable side by side comparisons of traditional aspect ratio vanes versus the proposed modified vanes to quantify the potential differences in measured undrained strength. In addition, measured undrained strengths from the various vanes are compared to results of laboratory testing on the same sandy lean clay (i.e., direct simple shear and triaxial compression) to provide a better understanding of the differences between the in-situ and laboratory test methods. This paper presents the apparatus developed to allow full scale vane shear tests to be conducted in the laboratory and summarizes the results of tests on a normally consolidated sandy lean clay
Deformability Parameters in the Offshore In-Situ-Test Survey for the New Breakwater Project in Genova Italy
Get PDFThe harbour of Genova is currently protected by a breakwater barrier that is 4 km long. One of the ongoing PNRR projects in Italy consists in dismissing the current breakwater and rebuilding it farther away from shore. The new breakwater will extend to a length of over 6.2 km and allow large cargo and container ships with over 400 m length to access the harbour. The new breakwater will lie in the currently open and unprotected water of the Genova Bay, with water depths up to 50 m. An extensive in situ test campaign of CPT and DMT tests was carried out for soil characterization, to provide stratigraphy, deformability and strength parameters required for the design of the new breakwater foundations. The Manta seafloor penetrometer designed by Geomil was deployed with a crane, operating from a floating pontoon anchored in turn on each of the test locations. The fully automated version of the flat dilatometer (Medusa DMT) and a CPTU tip were alternatively pushed by the Manta, with penetration depths up to over 27 m from seabed. This paper presents results of the moduli obtained from DMT tests employing the standard Marchetti’ formulas and compares them with the interpretation from the CPT using different correlation factors. Additionally, the correlations between Bq (obtained from CPTU) and Ud (obtained from DMT) are analysed
DMT-based liquefaction assessment accounting for the fines content effect: a case study Emilia-Romagna italy
No full textSimplified methods for seismic liquefaction assessment based on the flat dilatometer test (DMT), in which the liquefaction triggering curve is defined based on the horizontal stress index (KD), have been proposed over the years. One major drawback of the existing methods, valid for clean sand, is the lack of a correction factor for the fines content. An updating of the empirical relationship CRR-KD proposed by Chiaradonna and Monaco (2022) to incorporate the effects of the fines content is currently under development and validation. This paper illustrates the results obtained from application of the new method at the site of San Carlo – Terre del Reno (Ferrara) located in the Emilia-Romagna plain (Italy), where widespread liquefaction occurred in the 2012 seismic sequence. A comprehensive site characterization from previous insitu and laboratory tests carried out by various research groups is available for the sand, silty sand and sandy silt deposits in the San Carlo area. The performance of the new CRR-KD curve accounting for the fines content effect is compared with that obtained by adopting the “clean sand” curves proposed by Chiaradonna and Monaco (2022), as well as with that obtained by using the CPT-based method by Boulanger and Idriss (2014). Even though verified only for specific Italian soils in this area and requiring further field validation, the proposed approach appears as promising to improve the DMTbased liquefaction assessment in silty sands
Comparative Assessment of DMT-Based and CPT-Based Transformation Models for the Estimation of Shear Wave Velocity: a Case Study in Central Italy
Get PDFThe definition of the shear wave velocity profile is a fundamental step for the seismic characterization of a site in the context of Eurocode 8 and for the conduction of earthquake geotechnical engineering efforts such as site response analysis. Shear wave velocity profiles can be obtained: (1) directly from seismic geophysical and seismic geotechnical tests; or (2) indirectly, from “static” in-situ geotechnical tests such as dilatometer tests (DMT) and cone penetration tests (CPT). In the latter approach, shear wave velocity is estimated by using transformation models which are typically derived from data collected at other sites. This paper illustrates the procedures and main results of the comparative assessment of the performance of existing DMT-based and CPT-based transformation models to estimate shear wave velocity at two adjacent spatial locations in a rural site in the region of Tuscany in central Italy. Model-predicted shear wave velocity profiles were compared with direct measurements obtained by geophysical seismic dilatometer (SDMT) testing. The comparative assessment involved the definition, calculation, and assessment of quantitative performance statistics. The paper provides a critical analysis and a discussion of the outcomes with respect to soil type
Record of long-term field observation of large-scale cutting slope
Get PDFThis paper describes the interpretation of landslide behavior and verification of the effectiveness of countermeasure works based on the results of long-term field observations at a large-scale cutting site. The site has been subjected to various deformations since its construction due to its unique geological conditions, and has been monitored extensively by GPS surface displacement gauges, borehole inclinometers, anchor load cells, and water level gauges as an important monitoring site even after it was put into service. In the sixth year after the site was opened to public use, we assumed underground slip surfaces based on an interpretation of the observed data, constructed additional countermeasures, and verified the effectiveness of the countermeasures through continuous field observation of intermittent landslide behavior observed in several areas of the slope. As a result, it was confirmed that the displacement had not been settled even five years after the construction of the additional countermeasures and that a new slip surface had emerged, indicating the necessity of improving field observation techniques and data interpretation as well as continuous monitoring of this sit
Subsurface Characterization of Coastal Deposits using Measurement While Drilling
Get PDFMeasurement While Drilling (MWD) is a promising in situ test method that has gained increasing popularity in recent years. MWD can continuously characterize the subsurface while drilling any type of borehole in soil or rock without interfering with normal drilling operations. The latest MWD equipment gathers real-time data on numerous parameters that capture all aspects of the drilling process (e.g., depth, down thrust, rotation, torque, mud flow, and mud pressure). This paper summarizes MWD assessments performed in the coastal deposits of New Hampshire, USA. Profiles of individual and combined drilling parameters were used to differentiate between different soil layers and characterize subsurface conditions in complement with conventional, standardized geotechnical testing (e.g., SPT, CPTU) performed at adjacent boreholes. The results from this experimental campaign demonstrate the applicability of MWD systems to evaluate a broad range of geological conditions, from granular soils with erratic boulders to sensitive clays
Numerical Study of Cone Penetration in Calcareous Sands: Investigating Cone Tip Resistance Correction Factors for Crushable Soils
Get PDFThe cone penetration test (CPT) is used to characterize the behaviour and properties of soils, including the cyclic strength against earthquake liquefaction triggering. The cone tip resistance relates to cyclic strength through relative density, where relative density is closely related to both cone tip resistance and liquefaction susceptibility. Currently, published methods of estimating liquefaction potential (i.e., cyclic resistance ratio) are based on silica sands and do not properly characterize calcareous sands. The measured cone tip resistance in calcareous sands is lower than in silica sands at the same relative density; this difference is generally attributed to the higher compressibility of calcareous sands due to particle crushing during cone penetration. Consequently, application of CPT-based liquefaction triggering evaluations in calcareous sands result in over-conservative analysis. To avoid over-conservative analysis, projects may develop site-specific correction factors to adjust the cone tip resistance in calcareous sand to the equivalent value in silica sand at the equivalent relative density. This study aims to investigate cone penetration in calcareous sands compared to silica sands by examining the roles of soil compressibility and other fundamental soil parameters. The study is performed with a direct axisymmetric penetration model and the MIT-S1 constitutive model calibrated against published mechanical behaviour for a calcareous sand; the simulated cone penetration results are compared with simulated cone penetration in Ottawa F-65 sand. Compressibility of the calibrations is adjusted to explore the role of compressibility on cone tip resistance. The numerical results show that differences in compressibility only partially account for differences in cone tip resistance between calcareous and silica sands at the same initial state. However, the results support that critical state line position does strongly relate to differences in cone tip resistance between the two soil types. The study results provide a basis to investigate differences in critical state line position as a basis for site-specific cone tip resistance correction factors for calcareous soils