Aceh International Journal of Science and Technology
Not a member yet
294 research outputs found
Sort by
Effects of Drying Time on Yield and Moisture Content of Sumahe Powdered Drink Using Spray Dryer
Get PDFAs people today are becoming more health-conscious, various effortshave been madeto keep up ones health, such as by consuming highly nutritious food and drinks. One of the nutritious food sources produced from bees is honey, bioactive compounds of polyphenols,glyoxalandmethylglioxal. Honey could be used as a health drink by mixing with ginger. This health drink is also produced as powdered drink to simplify storing,reducethe use of plastic packaging, and to add product value to increase market share. The aim of this research was to analyze the effects of drying time for 5, 15, and 25 minutes with anaddition ofmaltodextrin on the yield, density, and moisture content of Sumahe instant powdered drink, made from cows milk, honey, and ginger. The results showed that the longer the drying time, the lower the moisture content of the drink. Meanwhile, the longer the drying time, the higher the yield became. A taste test of Sumahe also indicated that from 25 minutes of drying time, most of the panelists rated the drink as tasteful and delicious
Liquefaction Assessment Using the CPT and Accounting for Soil Ageing
Get PDFDue to its continuous data recording capability, excellent repeatability and accuracy, relatively low cost and simplicity of operation, the cone penetration test (CPT) offers enhanced liquefaction assessment over its predecessor the standard penetration test (SPT). However, soil ageing, which influences the cyclic resistance ratio (CRR), is difficult, if not impossible, to be detected by the CPT due to disturbance during the test. This situation may lead to excessively conservative estimation of CRR values which result in conservative assessment of liquefaction potential. This paper presents and discusses liquefaction assessment using the CPT and methods for accounting for soil ageing. A field study, conducted at Gillman, South Australia, is presented and the study site is assessed for liquefaction potential. This paper also explores the influence of soil ageing on the subsequent liquefaction assessment
Bioflocculation Activity in Harvesting System: A Biotechnology Approach for Microalgae Biomass
Get PDFA study on Ankistrodesmus sp.a freshwater green microalgae speciesas a bioflocculant based on its physicochemical properties and flocculation rate has been carried out. The molecular identification via 16S rDNA showed 99% resemblance of this green microalga to the Ankistrodesmus fumigatus strain. The optimum batch culture condition for the bioflocculant production was initiated by 10% inoculum (v/v). The low-concentrated bioflocculant of 10% (v/v) is considered as thermostable with a high flocculation rate to harvest the biomass of Chlorella sp. at a pH range of 5 to 9. The source of molasses, the mixture of yeast extract were used as the optimum sources of carbon and Ammonium sulfate were used as the optimum sources of nitrogen in the growth medium. Ankistrodesmus sp. bioflocculant has a high flocculation efficiency over a wide range of pH (59) with a low dose requirement of 10% v/v at 25C. Hence, it is immensely competitive to promote the economic viability of the production process. Accordingly, Ankistrodesmus sp. bioflocculant has a high potential to be applied on an industrial scale in tropical regions as it does not require additional production cost
Surface Structural Analysis of the Layered Perovskite Ca1.9Sr0.1RuO4 by Low Energy Electron Diffraction I-V
Get PDFAbstract The atomic structure at surface of the layered perovskite Ca1.9Sr0.1RuO4 has been studied by Low Energy Electron Diffraction (LEED) I-V. The perovskite Ca1.9Sr0.1RuO4 of single crystal was cleaved in ultra high vacuum chamber (the pressure in the chamber was about 1x10-10 Torr). The experiments were conducted at room temperature (T=300 K). The sharp LEED pattern was observed which indicates that the surface of Ca1.9Sr0.1RuO4 is flat and it is a well ordered crystal. LEED I-V data, nine equivalent beams of the layered perovskite Ca1.9Sr0.1RuO4 were recorded at room temperature. LEED I-V calculation was performed to fit experimental data to obtain the surface atomic structure. The LEED I-V analysis reveals that in the surface of the layered perovskite Ca1.9Sr0.1RuO4 the RuO6 octahedra are rotated (in-plane rotation) alternating clockwise and counterclockwise. The in-plane rotation at the surface is 11 degree which is smaller than that in the bulk (13 degree). The Ru O(1) bond-length at the surface is found to be 1.936 which is about the same as in the bulk (1.939 ). The Ru O(2) bond length at the surface is 1.863 which is much shorter than that in the bulk (2.040 ). The volume of octahedral Ru-O6 at the surface is reduced by 9% with respect to the bulk. This finding shows that the atomic structure at surface of the layered perovskite Ca1.9Sr0.1RuO4is significantly different than that in the bulk. These lattice distortions strongly influence its electronic properties. Key words: Transition Metal Oxide; Perovskite; Surface Atomic Structure; LEED I-
The Unit Price Implication of Reinforcement Usage in Tie Beam Reinforced Concrete Construction
Get PDFThe construction cost as one of the most important project resources should be planned and use efficiently. Cost estimation can be analysed using standard of unit price analysis according to Indonesian National Standard (SNI 7394:2008). Related to unit price analysis for tie beam reinforced concrete, the standard mentioned a specific analysis that combine all materials requirement include reinforcement (unit price analysis No. 6.29). In such analysis, reinforcement requirement is stated as much as 200 kg/m3 of concrete. Considering the diversity of dimension design of building structure caused by geographical location and building function, a further study required to response these problems. This research is aimed to provide information to what extent the unit price analysis related to tie beam reinforced concrete can be enforced in cost estimating. Research process initiated with secondary data collection to building construction located in zone 10 and 15 based on earthquake zone map (SNI 1726:2012) in Province of Aceh. The results of analysis informed that the ratio of reinforcement requirement of tie beam in zone 10 is 198.03 kg/m3 to 217.26 kg/m3 of concrete with average ratio 209.83 kg/m3. For zone 15, reinforcement requirement ratio is 203.76 kg/m3 to 233.83 kg/m3 of concrete with average ratio 215.17 kg/m3. The Potential inaccurate of cost estimation appears in the two review zones. Such inaccuracies may have an impact on the insufficient costs for the work. Thus, the use of the standard unit price analysis needs further assessment for proper application
Luwak Coffee Classification Using UV-Vis Spectroscopy Data: Comparison of Linear Discriminant Analysis and Support Vector Machine Methods
Get PDFUV-Vis spectroscopy has been used as a promising method for coffee quality evaluation including in authentication of several high-economic coffee types. In this paper, we have compared the abilities of linear discriminant analysis (LDA) and support vector machines classification (SVMC) methods for Luwak coffee classification. UV-Vis spectral data of 50 samples of pure Luwak coffee and 50 samples of pure non-Luwak coffee were acquired using a UV-Vis spectrometer in transmittance mode. The results show that UV-Vis spectroscopy combined with LDA and SVMC was an effective method to classify Luwak and non-Luwak coffee samples. The classification result was acceptable and yielded 100% classification accuracy for both LDA and SVMC methods. However, due to the simplicity and volume of the required calculation, in this present study LDA method is superior to SVMC method
Optimization of Multiple Response Using Taguchi-WPCA In ST 60 Tool Steel Turning Process With Minimum Quantity Cooling Lubrication (MQCL) Method
Get PDFA research was conducted for the optimization of the turning process st 60 tool steel with multiple performance characteristics based on the orthogonal array with Taguchi-WPCA method. Minimum Quantity Cooling Lubrication (MQCL) metode was applied as a coolant. The experimental studies were conducted under varying the cutting speed, feeding, depth of cut and type of coolant. The optimized multiple performance characteristics were surface roughness, and material removal rate. An orthogonal array, signal-to-noise ratio, grey relational analysis, weighted pricipal component analysis and analysis of variance were employed to study the multiple performance characteristics. Experimental results show that cutting speed gives the highest contribution for minimize of surface roughness and maximize of material removal rate, followed by feeding speed, type of coolant and depth of cut. The minimum of surface roughness and maximize of material removal rat could be obtained by using the values of cutting speed, feeding speed, depth of cut and type of coolant of 172.95 m/minute, 0.053 mm/rev, 0.25 mm, and vegetable oil as a coolant respectively
Feasibility of on-Street Parking Based on Degree of Saturation
Get PDFOn-street parking leads to reduced road capacity and decreased traffic performance of the certain road. Therefore, this study was conducted to evaluate the feasibility of on-street parking based on road performance. The study was conducted at Central Business District namely Peunayong, Banda Aceh. Based on the Indonesian Highway Capacity Manual (IHCM) one of the performance parameter values is Degree of Saturation (DS). The data needed for calculation of DS are the geometric conditions, traffic volume and the side frictions. The results indicate that on-street parking facilities on segment 2 of Khairil Anwar Street should be evaluated, as the DS value is greater than 0.75 (unstable road condition), by changing parking patterns into a parallel configuration or eliminating parking facilities. Furthermore, the parking configuration of R.A. Kartini Street also needs to be rearranged. Despite the stable road performance, this road is uncomfortable to pass because there is only one lane remained due to unfeasible parking patterns and existence of street market along the segment. The road performance of Khairil Anwar Street (segment 1), Ahmad Yani Street, W.R Supratman Street, T.P. Polem Street, Twk. Daudsyah Street and Ratu Safiatuddin Street is in stable condition, with DS 0.75. This indicating that on-street parking facilities can be maintained. While as for the W.R. Supratman and Ahmad Yani Street should be evaluated in year of 2019 to avoid traffic jam along this corridors
Voice Control in Calorie Tracker Application using Levenshtein Distance Algorithm
Get PDFEach food consumed by people contains a number of calories needed by the body to perform an activity. Calories can be described as fuel of engine to move and carry out tasks. Publics indifference to the food consumed can cause some negative effects on health like, too skinny, obesity, and emergence of various diseases. Therefore, it is necessary to have an application which can provide some information about the calorie needs, so that user can control the calorie intake. This paper describes the development of an application to assist user in controlling calorie intake according to the calorie needs. This application supports voice control feature to improve user comfort in performing certain commands and inputting food consumed. In addition, this application also uses Levenshtein Distance algorithm to correct food recognition errors which is spoken by user. This application is developed using Java programming language for Android with SQLite database
Inhibitory action of rice husk extract (RHE) on the corrosion of carbon steel in acidic media
Get PDFThe study investigates the inhibition characteristics of rice husk extract (RHE) on the corrosion of mild steel in 1M acidic media. Mass loss, Fourier Transform Infrared Spectroscopy (FTIR), phytochemical analysis were used as basis for studying the corrosion inhibition behaviour of the extracts. The analyses of the results showed that as concentration increases, there was increase in the inhibitor while increase in temperature reduces the inhibition respectively. Moreover, the highest inhibition efficiency was 94.24 % at 40 oC and 0.25 g/l inhibition concentration in sulfuric acid medium while inhibition efficiency of 89 % at 60 oC and 0.20 g/l inhibition concentration in hydrochloric acid. The thermodynamic parameters revealed that the adsorption of extract onto the metal surface was spontaneous. Langmuir isotherm best fits the data obtained suggesting physical adsorption as the adsorption mechanism between the extract and the mild steel substrate. The results from the FT-IR spectroscopy showed that the organic compounds found in Rice husk made it a good inhibitor