MRC Laboratory of Molecular Biology
CUED - Cambridge University Engineering DepartmentNot a member yet
45551 research outputs found
Sort by
A Compact Full 2π Flexoelectro-Optic Liquid Crystal Phase Modulator
No full textWavefront shaping, which is often achieved using liquid crystal (LC) spatial light modulators, is particularly important for a wide range of applications including laser microfabrication and micromanipulation, microscopy, and quantum optics. In this work, results are presented for the first integrated LC phase modulator that combines a flexoelectro-optic LC layer (that behaves as a switchable λ/2 waveplate) with a polymerized reactive mesogen layer (which acts as a λ/4 waveplate) and a mirrored substrate that creates a double-pass geometry. For a flexoelectro-optic LC layer that exhibits switching angles of ±45° at a voltage of ±85 V a full 2π phase modulation is observed when driven by a 1 kHz waveform. Experimental results are also compared with modeling using Jones calculus of the amplitude and phase variation when the LC and the polymer layer deviate from their desired waveplate conditions. The development and demonstration of an integrated device is particularly significant for applications where size and cost are critical factors such as in LiDAR for the Space and Automotive industries, respectively
Observations during suction bucket installation in sand
No full textSuction buckets represent a viable solution as foundations for offshore wind turbines. Installation in sand is relatively straightforward, albeit with limited understanding of the resulting changes in soil state. This paper describes an experimental methodology that allows for visualisation and quantification of changes in soil state during suction bucket installation, validated in sand. Insights obtained from particle image velocimetry analyses, performed on images of a half-bucket installing against a Perspex window taken in a geotechnical centrifuge are discussed. Compared with the initial self-weight penetration, the deformation mechanism governing the suction-assisted phase shows a preference for the soil below the skirt tips to move inwards and upwards inside the bucket. The installation process is responsible for changes in relative density and permeability within the bucket. In these experiments, the majority of the soil plug heave can be attributed to the soil displaced inwards by the advancing skirts, with a minor contribution caused by dilation. The confidence in the experimental methodology provided through the results of suction bucket installation in sand discussed herein now enables suction bucket installation in more complex seabeds to be investigated
Inclined Perimeter Drains Performance as Liquefaction Countermeasure Techniques below Existing Buildings
No full textReducing the risk of structural damage due to earthquake-induced liquefaction in new and existing buildings is a challenging problem in geotechnical engineering. Drainage countermeasure techniques against liquefaction have been studied over the last decades with an emphasis on the use of vertical drains. This technique aims to allow a rapid dissipation of excess pore pressures generated in the soil during the earthquake thereby limiting the peak excess pore pressures and consequently improve the structural response. Rapid drainage in the post-earthquake period in the presence of these drains helps quick recovery of the soil strength. Recent studies propose different variations in the vertical drains arrangement to improve the excess pore pressure redistribution in the soil around structures. However, conventional arrangements for existing buildings do not achieve an adequate proximity from the drains to the soil below the foundation. To address this, the performance of inclined and vertical perimeter drain arrangements are studied in this paper. Dynamic centrifuge tests were carried out for the different arrangements in order to evaluate the excess pore pressure generation due to ground shaking and the following dissipation together with the foundation settlement and dynamic response
Frugal innovation in a crisis: the digital fabrication maker response to COVID-19
No full textThe rapid spread of COVID-19 has led to a global shortfall in essential items, turning many countries into resource-constrained environments. In response, an unprecedented number of do-it-yourself hobbyists (i.e. makers) have started to use digital fabrication tools to produce critical items. These bottom-up communities are mobilising as part of a global movement to produce innovative solutions to much-needed items, such as face masks, face shields and ventilators. As these individuals tackle widespread resource constraints, the conceptual lens of frugal innovation becomes highly relevant to study how these solutions developed. Frugal innovation is a type of resource-constrained innovation that refers to the practice of doing more with less, for more people. In this study, we present two instrumental case studies of maker projects that use digital fabrication to tackle COVID-19. The first case study is from Italy (a High Income Country) and the second is from India (a Lower Middle Income Country). We analyse the frugality of these cases and highlight their similar approaches. In doing so, we suggest that current theories of frugal innovation can be expanded to new geographical and technological contexts. We put forward that frugal innovation is an important strategy in crisis response beyond emerging markets and that digital fabrication can be considered as an important frugal innovation enabler, both in its ability to produce frugal solutions and to support distributed networks of innovation actors. This study advances knowledge on how frugal innovation unfolds in the Maker movement. It is among one of the first studies to connect the domains of makers and frugal innovation, and the paper concludes by identifying several promising areas for further research
Confidence Estimation for Black Box Automatic Speech Recognition Systems Using Lattice Recurrent Neural Networks
No full textRecently, there has been growth in providers of speech transcription services enabling others to leverage technology they would not normally be able to use. As a result, speech-enabled solutions have become commonplace. Their success critically relies on the quality, accuracy, and reliability of the underlying speech transcription systems. Those black box systems, however, offer limited means for quality control as only word sequences are typically available. This paper examines this limited resource scenario for confidence estimation, a measure commonly used to assess transcription reliability. In particular, it explores what other sources of word and sub-word level information available in the transcription process could be used to improve confidence scores. To encode all such information this paper extends lattice recurrent neural networks to handle sub-words. Experimental results using the IARPA OpenKWS 2016 evaluation system show that the use of additional information yields significant gains in confidence estimation accuracy. The implementation for this model can be found online1
High Efficiency Dopant Free a-Si:H Solar Cell
No full textIn order to advance the thin film silicon solar cell technology, it is desirable to replace the layers of doped thin film silicon or its alloys with alternative materials that can be deposited by simple physical vapor deposition (PVD) methods. Here, a dopant free a-Si:H solar cell design of Asahi U substrate| MoOx | a-Si:H | LiF | Al is investigated. All the layers, except the intrinsic a-Si:H absorber layer, are deposited by PVD methods. This cell has a power conversion efficiency of 8.02% under the standard test conditions
In-Plane Amorphous Oxide Ionotronic Devices and Circuits with Photochemically Enabled Favorable Interfaces
No full textHere, we demonstrate a side-gated in-plane structure of solution-processed amorphous oxide semiconductor ionotronic devices and logic circuits enabled by ion gel gate dielectrics with a monolithically integrated nanoscale passivation architecture. The large capacitance of the electric double layer (EDL) in the ion gel allows a device structure to be a side gate geometry, forming an in-plane structured amorphous In-Ga-Zn-O (a-IGZO) ionotronic transistor, which can be translated into a simplified logic gate configuration with a low operation voltage. Particularly, the monolithic passivation of the coplanar electrodes offers advantages over conventional inhomogeneous passivation, mitigating unintentional parasitic leakage current through the ion gel dielectric layer. More importantly, the monolithically integrated passivation over electrodes was readily obtained with a complementary metal-oxide semiconductor-compatible photochemical process by employing a controlled ultraviolet light manipulation under ozone ambient, which introduced not only much enhanced electrical characteristics but also a scalable device architecture. We investigated various electrical behaviors of the side-gated a-IGZO ionotronic transistor based on EDL, which is called an electric double layer transistor (EDLT), and logic circuits enabled by photochemically realized monolithic aluminum oxide (AlOX) passivation comparing to the native or polymerized passivation layer, which reveals that the photoassisted AlOX secures high-performance a-IGZO EDLTs with a low off current (1.87 × 105), and exceptional high carrier mobility (>14.5 cm2 V-1 s-1). Owing to the significantly improved electrical characteristics, an inverter circuit was successfully achieved with broad operation voltages from an ultralow VDD of 1 mV to 1.5 V, showing a fully logical voltage transfer characteristic with a gain of more than 4 V V-1
Self-aligned top-gate metal-oxide thin-film transistors using a solution-processed polymer gate dielectric
No full textFor high-speed and large-area active-matrix displays, metal-oxide thin-film transistors (TFTs) with high field-effect mobility, stability, and good uniformity are essential. Moreover, reducing the RC delay is also important to achieve high-speed operation, which is induced by the parasitic capacitance formed between the source/drain (S/D) and the gate electrodes. From this perspective, self-aligned top-gate oxide TFTs can provide advantages such as a low parasitic capacitance for high-speed displays due to minimized overlap between the S/D and the gate electrodes. Here, we demonstrate self-aligned top-gate oxide TFTs using a solution-processed indium-gallium-zinc-oxide (IGZO) channel and crosslinked poly(4-vinylphenol) (PVP) gate dielectric layers. By applying a selective Ar plasma treatment on the IGZO channel, low-resistance IGZO regions could be formed, having a sheet resistance value of ~20.6 kΩ/sq., which can act as the homojunction S/D contacts in the top-gate IGZO TFTs. The fabricated self-aligned top-gate IGZO TFTs exhibited a field-effect mobility of 3.93 cm2 /Vs and on/off ratio of ~106, which are comparable to those fabricated using a bottom-gate structure. Furthermore, we also demonstrated self-aligned top-gate TFTs using electrospun indium-gallium-oxide (IGO) nanowires (NWs) as a channel layer. The IGO NW TFTs exhibited a field-effect mobility of 0.03 cm2 /Vs and an on/off ratio of >105 . The results demonstrate that the Ar plasma treatment for S/D contact formation and the solution-processed PVP gate dielectric can be implemented in realizing self-aligned top-gate oxide TFTs
The effect of bed roughness uncertainty on tidal stream power estimates for the Pentland Firth
No full textUncertainty affects estimates of the power potential of tidal currents, resulting in large ranges in values reported for sites such as the Pentland Firth, UK. Kreitmair et al. (2019, R. Soc. open sci. 6, 180941. (doi:10.1098/rsos.191127)) have examined the effect of uncertainty in bottom friction on tidal power estimates by considering idealized theoretical models. The present paper considers the role of bottom friction uncertainty in a realistic numerical model of the Pentland Firth spanned by different fence configurations. We find that uncertainty in removable power estimates resulting from bed roughness uncertainty depends on the case considered, with relative uncertainty between 2% (for a fully spanned channel with small values of mean roughness and input uncertainty) and 44% (for an asymmetrically confined channel with high values of bed roughness and input uncertainty). Relative uncertainty in power estimates is generally smaller than (input) relative uncertainty in bottom friction by a factor of between 0.2 and 0.7, except for low turbine deployments and very high mean values of friction. This paper makes a start at quantifying uncertainty in tidal stream power estimates, and motivates further work for proper characterization of the resource, accounting for uncertainty inherent in resource modelling