BAM-Publica - Publikationsserver der Bundesanstalt für Materialforschung und -prüfung
Not a member yet
58839 research outputs found
Sort by
Werkstoffsichere Dickblechschweißung und KI
No full textDer Vortrag zeigt, welche Herausforderungen beim Schweißen sogenannter Dickblechverbindungen bestehen und welche Strategien zur Lösung genutzt werden können. Ansätze zur Fehlerprävention werden vorgestellt. Es wird dargestellt, wie KI-basierte Methoden die Fehlererkennung erleichtern. Letztlich werden Potentiale zur effizienten Fehlerbeseitigung aufgezeigt und der Anwendernutzen herausgestellt
Begrüßung und Vorstellung der BAMund des Fachbereichs 9.2 - Zentrale Forschungswerkstatt
No full textDie Zentralwerkstatt der BAM übernimmt die Fertigung und Konstruktion komplexer Prüf- und Versuchseinrichtungen und adressiert zugleich zentrale Forschungsthemen zur Werkstoff- und Komponentensicherheit. Dazu gehören die Entwicklung innovativer Fertigungstechnologien, ressourceneffiziente Verarbeitungskonzepte für hochfeste und additive Komponenten sowie die Untersuchung von Fertigungseinflüssen auf Oberflächenintegrität und Werkstoffdegradation. Ein besonderer Fokus liegt auf der H₂-Sicherheit, insbesondere der Fertigung und Prüfung von Hohlzugproben für Wasserstoff-Pipelines. Ergänzend werden Automatisierungslösungen, digitale Methoden und moderne Spanntechnik zur Effizienzsteigerung eingesetzt. Die Arbeiten sind eng mit den BAM-Kompetenzzentren AM@BAM, H2Safety@BAM und WIND@BAM verzahnt und leisten einen Beitrag zur Energiewende sowie zur Normung und zum Technologietransfer
Phytolith assemblages from palm leaves and palm-leaf manuscripts: what is the difference and what it could mean?
No full textWe studied freshly collected, dried and herbarized leaf fragments of two palms, namely Borassus flabellifer L. and Corypha umbraculifera L., most commonly used for palm-leaf manuscript (PLM) production in South (S) and Southeast Asia (SE) in order to reveal differences in their phytolith assemblages. For each of the two palms, 25 leaf samples were taken from the two Indian states of Kerala and Tamil Nadu. Dried leaf material was obtained from the fresh one by drying the leaves in air. Herbarium samples were obtained from two independent herbaria, specimen origin comprises S and SE Asia with the main focus on South India and Sri Lanka. Additionally, 25 manuscripts made of Borassus flabellifer leaves and 25 manuscripts made of Corypha umbraculifera leaves were investigated for phytoliths. All manuscripts are preliminary dated back to between the 16th and the beginning of the 20th century CE; most of them assumedly were produced in S India (Tamil Nadu and Kerala), Sri Lanka, Burma or Indonesia. Phytolith assemblages significantly differed between fresh, dry and herbarized palm leaves in comparison to PLM material, both qualitatively and quantitatively (mean r2 = - 0.61 ± 9.3 for Borassus samples and r2 = - 0.75 ± 5.3 for Corypha samples, at p < 0.001). Fifty-three phytolith types described for PLM material were not observed in any of the fresh, dry or herbarized palm-leaf samples. Geographical analysis of PLM-specific phytoliths suggests that the combination of those phytoliths could be region-related. In this paper, we prove that the methods of palaeoecological reconstructions based on detailed microscopy of the PLMs surface and phytolith analysis applied in combination with methods of mathematical and computer data analysis can contribute to answer the questions posed by material codicology by revealing lost manuscript production recipes and by studying manuscript provenance in terms of the geographical origin of the artefacts. Our approach can potentially open a new perspective for palaeoecological studies expanding their traditional scope and making them applicable to a new research field
Digital object identifier for additively manufactured parts as software package
No full textA method to uniquely identify samples without printed or handwritten labels is an advantage not just for additively manufactured parts. To kickstart industry use cases, it is also important to provide a ready-made implementation kit. Following an open-science and open-source software approach Germanys Federal Institute for Materials Research and Testing (BAM) seeks to promote digital solutions of ongoing research projects. With this software package a novel method based on microstructural features as identifiers – DOI4AM (digital object identifier for additively manufactured parts) – will be explained alongside its implementation as open-source Python software package. The digital object identifier (DOI) links product data clearly and forgery-proof with real components. Its implementation helps to identify and securely authenticate additively manufactured components during its product life cycle by using characteristic microstructure features - just like a fingerprint. To calculate the DOI fingerprint, a few preprocessing steps need to be performed to detect the uniquely distributed microstructure features that occur during the 3D printing process. A go-through guide shows the preprocessing steps that include CT image capturing, feature segmentation, and data distribution with CSV files. While all steps can be followed along in a Jupyter notebook, the software package includes an application for creating and checking of previously created fingerprints, as well, as a containerized API (application programming interface) service for implementation in existing software platforms or workflows. While data visualization is crucial to understanding the methodology and an essential tool to check for data correctness, an implementation in an industry use case needs to be slim and resource efficient. Therefor the software’s API can be used as an independent service. The project's industry partner proofs its first successful implementation in their digital product passport web solution PASS-X
Embedded Sensors for Quality Control and Structural Integrity Monitoring of Large-scale 3DCP Structures
No full textIn extrusion-based 3D concrete printing (3DCP), addressing challenges related to safety, reliability, and quality control is crucial for widespread adoption. Yet current limitations in monitoring material properties during and after printing hinder the development of effective 3DCP guidelines. Therefore, the development of an inline sensing system capable of real-time monitoring and adjustment of process parameters is necessary to overcome these challenges.
Building upon an existing inline sensing system developed by BAM, which currently monitors material properties during printing and the geometry of the print post-extrusion, this study extends its capabilities to post-extrusion monitoring using embedded piezoelectric (PZT) sensors. These PZT sensors provide localized measurements of material changes through electrical impedance (EI) measurements without disrupting the printing process. By embedding these sensors in 3D printed structures, continuous monitoring is achieved from layer deposition through 1-day of hydration. To achieve this, initially, PZT sensors were developed with multiple layers of protective coatings. Two different 3D printed mixtures, each with different hydration behaviors, were utilized, and PZT sensors were strategically placed between printed layers to maintain their integrity. EI measurements were collected continuously from printing through 1 day of hydration. Analysis of amplitude and frequency changes in the EI response spectrum provided insights into material behavior post-printing. The study highlights how continuous monitoring of frequency and conductance can track structural builtup and property development of the material. Rapid changes in conductance measurements, immediately post-printing indicate swift structural built-up, while key hydration phases are reflected in frequency measurements
Distributed Fibre Optic Monitoring of Hydrogen Storage Composite Pressure Vessels for Automotive Use
No full textWe present our research work on the condition monitoring of hydrogen storage composite pressure vessels using distributed fibre optic sensors. The sensing fibres are integrated into the composite structure by wrapping them over the polymer liner in the helical and circumferential direction during the manufacturing process of the carbon fibre reinforced polymer. The following use of optical backscatter reflectometry allows for continuous condition monitoring and precise detection and localization of structural damages during the entire service life. To account for the time-dependent strength degradation of the composite pressure vessels, both slow burst and ambient hydraulic cycling tests, respectively, were conducted on five 70 MPa pressure vessels with integrated fibre optic sensors. The results achieved via distributed fibre optic strain sensing demonstrate a near linear strain response to pressure suitable for sensitive condition monitoring and confirm the required robustness of the selected sensor solution
Ce3+-doped chalcogenide glass fibre for laser beyond 4 microns wavelength: Glass material-integrity
No full textThe 4-μm wavelength barrier encountered for mid-infrared fibre lasing based on heavy metal fluoride glasses has been overcome. We reported, in 2021, the first continuous wave, mid-infrared fibre laser operating beyond 4 μm at room temperature in a fibre with a Ce3+-doped selenide-chalcogenide core. Defects, such as crystallites in the core glass, could cause unwanted light-scattering, diminishing fibre laser efficiency. It is important to identify such optical loss mechanisms and eradicate them. Here, we report on investigating the material nano-structure of a chalcogenide-glass lasing fibre which exhibits 7 mW laser power output; the fibre has a Ce3+-doped core (8.5 μm diameter), concentrically surrounded by an inner- and outer-cladding, where both cladding-glasses are nominally the same composition. High resolution transmission electron microscopy and electron diffraction show that the core, inner-cladding and outer-cladding of the lasing fibre are internally nano-crystallite-free and amorphous. However, the external outer surface of the last 10 m of fibre drawn, of the total 100 m, contains monoclinic GeSe2 crystallites adjacent to discrete, small (<0.5 mm) wrinkled defects. The final length of fibre is drawn from the final part of the glass fibreoptic preform. The glass preform has as its outermost component an extruded chalcogenide glass tube. It is the last part of the tube which spends the longest time at high temperature inside the extruder during tube manufacture, encouraging heterogeneous nucleation at the tube outer-surface in contact with the extruder. These heterogeneous nuclei subsequently nucleate crystal growth during fibre-drawing in the outermost fibre surface
Thermal radiation of inclined large scale hydrogen jet flames
No full textIn order to assess the thermal radiation emanating from hydrogen jet flames, experiments under real scale conditions were carried out at the Test Site Technical Safety of BAM. Herein, the behavior of inclined hydrogen jet flames was investigated. The aim of the work is to determine the Surface Emissive Power and radiant heat fraction of these flames and to provide a reliable dataset for model evaluation purposes. Since the aforementioned values are not directly measurable, the incident heat radiation was measured at defined distances from the flame, as well as the flame's shape and size. The required values were then derived from these measurements. The hydrogen releases ranged from 0.005 kg/s to 0.175 kg/s with a 30 mm orifice. The mass flows were held constant during the releases, nevertheless a transient behavior of the flame could be observed since the experiments were carried out under open field conditions, with unsteady wind fields. In the literature, the flame lengths are often determined using visible light imaging, either by injecting coloring substances in the low light emitting hydrogen jet flame or by carrying out the measurements in darkness. In this work the jet flames were visualized using infrared (IR) and OH* imaging. The recorded flame shapes and resulting flame lengths are compared. Results from this showed that the flame lengths determined with OH* and IR recordings differ greatly. A flame length ratio l_(f OH*)/l_(f IR) in the range of 0.47-0.62 can be found. In addition, the SEP differ also in the range of 10 kW/m²-16 kW/m² (IR) and 40 kW/m²-80 kW/m² (OH*) for hydrogen jet flames due to differences in the determined flame surface. Conclusions regarding the determined x_(RAD )values for IR and OH* result in approximately the same range of 0.031-0.043
Development of a fully automated slurry sampling introduction system for GF-AAS and its application for the determination of cadmium in different matrices
No full textelement analysis, offering high sensitivity and precision. However, its effectiveness is limited by sample preparation challenges for solid samples like soils and microplastics. Traditional methods include sample preparation, such as digestion, which is time-consuming and involves reagents, like acids, contributing to measurement uncertainty and higher carbon footprints. Slurry sampling allows direct analysis of suspensions, offering a more efficient alternative. However, maintaining suspension stability is challenging, requiring robust autosampler systems to streamline the process and enhance analytical performance.
Results: We present a novel autosampler extension for slurry sample introduction into GF-AAS. This system ensures suspension stability with a stirring device and closed vessels to prevent evaporation and contamination, incorporating a cooling unit to reduce solvent and analyte losses. It installs and removes in minutes without
additional connections. Validation with cadmium analysis in BAM-U110 (Soil) and BAM-H010 (ABS) showed high reliability. For BAM-U110 (Soil), we achieved recovery rates of 94 % ± 13 % in water suspension. The recovery rate for BAM-H010 (ABS) was 104 % ±11 % in acetonitrile suspension. These results demonstrate the system’s robustness, versatility, and accuracy for different matrices.
Significance:
The autosampler extension helps solve key problems in trace element analysis of solid samples, making the process faster and more accurate. It works well with complex materials, making it useful for areas like microplastic or nanoparticle analysis. This improvement also helps meet regulations for monitoring environ mental and polymer samples, offering a reliable and flexible tool for high-throughput analysis with fewer errors
Quantification of in-plane stress development during drying of tape-cast ceramic layers by cantilever deflection method
No full textThe control of stress development in cast ceramics during drying is usually one of critical steps in ceramic processes, which is important also for additive manufacturing technologies using a suspension as feedstock. This work introduces a method based on the cantilever deflection method, to simultaneously quantify the kinetics of solvent evaporation, the shrinkage and the intensity of in-plane stresses developed during drying. Particular attention is given here to the experimental limits of the method and to the optimization of the experimental conditions to suitably measure the intensity of in-planar stress in the coating. The optimized method is applied to
four alumina slurries for the water-based additive manufacturing technology LSD-print. Four stages of drying are identified and discussed in relation with the granulometry and morphology of the alumina ceramic particles