International Journal of Innovation in Mechanical Engineering and Advanced Materials
Not a member yet
93 research outputs found
Sort by
NATRIUM CARBONATE (NA2CO3) AS INHIBITOR IN THE CORROSION PROTECTION ON STEEL PIPE ST 41 IN WATER PLUMBING ENVIRONMENTAL
Get PDFThis study aimed to analyze the effect of adding to the rate of steel corrosion inhibitor and comparing the rate of corrosion on steel pipes with and without inhibitors. The testing conducted in Puspitek shown that the most optimum of the inhibitor contained with the addition of 1% due to changes of the pH from 7.30 to 11.80. This shows the increasing of pH occurred sizable value and followed by the declines of potential value (Ecorr) -700.53 mV to -512.39 mV. Thus, the decreasing occurred to the current corrosion value (Icorr) from 2.71 μA/cm2 to 0.31 μA/cm2, while the corrosion rate of carbon steel St 41 decreased most effective after adding 1% Na2CO3 as an inhibitor, the corrosion rate is changed from 1.2437 mpy to 0.1427 mpy
HIGH RESOLUTION IMAGING OF BORON DISTRIBUTION ON DIAMOND FILM USING ENERGY FILTERED TEM
Get PDFThe main difficulty in investigation of thin film systems is the lack of capability to get detail information of the material in nano level due to the low resolution of conventional imaging techniques such as SEM, SIMS etc. In this work Electron Spectroscopy Imaging (ESI) in energy filtered transmission electron microscope (EFTEM) was used to produce a real image of boron distribution in a diamond film deposited on (111) Si by chemical vapor deposition. The result revealed the layer consists of 1.3 μm thick diamond structured carbon film adjacent to Si substrate and 120 nm amorph carbon layer on top most surface. Boron atoms were distributed uniformly in both layer, however slight higher concentration in the second layer is observed. There was obviously no grain boundary enrichment of Boron atoms observed
LIFE EXTENSION TECHNIQUE FOR WELDED STRUCTURE USING HFMI/PIT: A REVIEW ON PAST AND CURRENT RESEARCHES WITH APPLICATIONS
Get PDFIn this paper, High Frequency Mechanical Impact (HFMI) using Pneumatic Impact Treatment (PIT) which can be applied for new or aging welded structure towards asset integrity will be discussed. The technology HFMI/PIT which falls under post weld treatment process is primarily aimed to enhance fatigue life and to strengthen welded joint. At first, the basic principle on fatigue of welded structure based on the IIW Recommendation will be briefly described. Further, various investigations conducted by prominent research universities or institutions and various industrial applications in European countries will be reviewed and discussed. Lastly, the current research on application of HFMI/PIT carried out under Advanced Manufacturing Technology Excellence Centre (AMTEx) at Faculty of Mechanical Engineering UiTM Shah Alam will be presented. As conclusion, it is stated that HFMI/PIT can be applied for extending the structural life and also for design optimization
BIODIESEL PRODUCTION FROM WASTE COOKING OIL BY USING ULTRASONIC TUBULAR REACTOR
Get PDFThe aim of this research is to find an optimum of synthesis biodiesel from waste cooking oil (WCO) using ultrasonic tubular reactor. The experimental studies explored the variations in reaction time, molar ratio WCO to methanol (MeOH), amount of catalyst, frequency of ultrasonic and output power ultrasonic on the ester contents. Comparisons of type ultrasonic and also mechanical stirring method based on time reaction were investigated. The optimum results of biodiesel process is the reaction time of 5 minute, NaOH catalyst 1%wt of WCO, molar ratio WCO to MeOH of 1:6, frequency ultrasonic of 20 KHz and output power ultrasonic of 650 W. The reaction time reduced 12-24 times compared to both of method and the yield of ester contents was obtained at 96.54%wt
DEVELOPMENT OF INTEGRATED GAS INSTRUMENTATION SYSTEM IN DIRECT REDUCTION PLANT
Get PDFDirect reduction is the removal of oxygen from iron without melting process. In direct reduction process, the presence of mixture gas in accordance levels largely determines the performance of the iron produced. Therefore, it needs gas sensors system which has high accuracy and reliability in this process. Unfortunately, there are some things that cause decreasing in the accuracy and reliability of the gas sensor in this process. This paper aims to offer a system that can preserve the accuracy and reliability of the gas measurement system called as Integrated Gas Instrumentation System. The system tends to integrate gas sensor component using Specific Gravity (SG) with other components, such as water trap, filter regulator and monitor gas flow rate. The values of Specific Gravity Meter based on process that display in DCS system are compared with lab results for three type of experiments. Based on experiment results it can be said that the proposed system is able to improve the accuracy and reliability of direct reduction process
EFFECT OF ANNEALING ON MAGNETIC AND STRUCTURAL PROPERTIES OF THE NANOCRYSTALLINE Fe-Mn-Al ALLOYS
Get PDFIn this work, the formations of Fe55Mn10Al35 nanocrystalline alloys were made by using mechanical alloying (MA) technique with the milling time of 24 hrs and then annealed at 300, 500, and 700oC. The sizes and the morphology of the particles were checked by using a Scanning Electron Microscope (SEM). The magnetic properties were characterized by using a Vibration Sample Magnetometer (VSM), and it give results both of the magnetic saturation (Ms) and Coercivity (Hc) are decreased respect to annealing temperatures. Last one; the structures were characterized by using an Extended X-ray Absorption Fine Structure (EXAFS) and X-Ray Diffraction (XRD). It give results that the structures were single phase at 24 hrs milled and 300oC annealed, then the structure to be changed at 500 and 700oC
SYNTHESIS AND CHARACTERIZATION OF TOLUENE SULFONIC ACID (TSA)-DOPED POLYPYRROLE NANOPARTICLES: EFFECTS OF DOPANT CONCENTRATIONS
Get PDFNanoparticles of the conducting polymer polypyrrole in toluene sulfonic acid (PPy/TSA) were synthesized and characterized. The polymerization was process carried out in situ using ammonium persulfate (APS) as an oxidant. The particles were synthesized by varying the dopant concentration of para-toluene sulfonic acid over five sulphonic acid concentrations. The main objective of this study was to examine the effect of TSA dopant concentrations on the properties of polypyrrole nanoparticles. Understanding nature and characteristics of polypyrrole/TSA nanoparticles are important in determining whether the nanoparticles have the potential to be a component in the manufacture of fuel cells. The conducting polymer particles synthesized in this study were characterized using a particle analyzer, X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), spectroscopy UV-visible (UV-vis), thermogravimetric analysis (TGA) and electrical conductivity measurement. XRD shows that the particles generated possessed an amorphous structure, as also indicated by SEM images revealing the formation of aggregated and granular composite particles. Furthermore, the FTIR peak between 1273 and 1283cm-1 indicated that sulfonic acids (SO3-) groups were present in the structure of PPy. The size of the PPy/TSA nanoparticles was determined to be approximately 24-51 nm, and their conductivity measured to be 1.3 x 10-1 S/cm
SIMILARITY AND NONSIMILARITY SOLUTIONS ON FLOW AND HEAT TRANSFER OVER A WEDGE WITH POWER LAW STREAM CONDITION
Get PDFThe similarity and non-similarity analysis are presented to investigate the effect of buoyancy force on the steady flow and heat transfer of fluid past a heated wedge. The fluid is assumed to be a Newtonian, viscous and incompressible. The wall of the wedge is an impermeable with power law free stream velocity and a wall temperature. Due to the effect of a buoyancy force, a power law of free stream velocity and wall temperature, then the flow field is similar when n = 2m - 1, otherwise is non-similar when n ≠ 2m - 1. The governing boundary layer equations are written into dimensionless forms of ordinary differential equations by means of Falkner-Skan transformation. The resulting ordinary differential equations are solved by Runge-Kutta Gill with shooting method for finding a skin friction and a rate of heat transfer. The effects of buoyancy force and non-uniform wall temperature parameters on the dimensionless velocity and temperature profiles are shown graphically. Comparisons with previously published works are performed and excellent agreement between the results is obtained. The conclusion is drawn that the flow field and temperature profiles are significantly influenced by these parameters
THE EFFORTS ON SUSTAINABILITY OF THE ACHIEVEMENT FKMP ON QS WORLD UNIVERSITY RANKING TOP 300 BY SUBJECT
Get PDFThis article review each vital elements and aspects that contribute to sustain recent achievement of Faculty of Mechanical and Manufacturing Engineering (FKMP), Universiti Tun Hussein Onn Malaysia by the QS world university ranking by subject in 2015. Some of recent and important issues are discussed and reviewed. The suggestions for improvements are also raised out for further reference
OPTIMIZATION OF SOLAR-WIND-DIESEL HYBRID POWER SYSTEM DESIGN USING HOMER
Get PDFIndonesia has a lot of potential for renewable energy. Electricity generation from hybrid solar and wind energy will be a prospective solution to fulfill electricity supply for remote and rural communities. Although diesel generator was still part of the hybrid power system, however, with a proper design, the fuel consumption could be reduced significantly. HOMER software was utilized to aid the design process by providing optimum configuration of the hybrid power system components in terms of performance and economy
Access Repository Dashboard
Do you manage International Journal of Innovation in Mechanical Engineering and Advanced Materials? Access insider analytics, issue reports and manage access to outputs from your repository in the CORE Repository Dashboard!