IYTE GCRIS Database (Izmir Institute of Technology)
Not a member yet
11968 research outputs found
Sort by
Numerical Analysis of Three Vertical Axis Turbine Designs for Improved Water Energy Efficiency
No full textA hydrokinetic turbine with a vertical axis is specifically designed to harvest the kinetic energy from moving water. In this study, three vertical axis water turbines, namely Gorlov, Darrieus, and Savonius turbines, were compared for their efficiency via numerical modeling for steady-state conditions via the ANSYS 2022 R2 Fluent model. The Semi-Implicit Method for Pressure-Linked Equations (SIMPLE) was implemented with an SST k-omega turbulence model. The dynamic mesh technique, which allows modeling according to changes in angular velocity at each time step, was used to simulate flow around the turbines for six different velocities (from 0.5 to 3 m/s). The efficiency of the turbines was compared and the results were analyzed. The pressure, velocity, and turbulence kinetic energy distributions around the rotor were measured at different rotational angles and results indicated a wider operating range for the Darrieus and Gorlov turbines compared to the Savonius turbine. The highest power coefficient of 0.293 was achieved in the model featuring a Darrieus turbine, corresponding to a TSR value of 1.34, compared to 0.208 for the Gorlov and 0.257 for the Savonius turbine, at TSR values of 1.3 and 1.06, respectively. Numerical modeling results pointed to a significantly higher self-starting capacity for the Savonius turbine compared to the others
Behavior of Enzymatic Membranes Under Pressure: Effect of Enzyme Location
No full textEnzyme immobilized membranes combine catalysis and separation functions. Their application in large-scale continuous processes requires knowing the behavior under pressure. Also, the effects of enzyme location on the mass transfer limitation, membranes’ stability, and filtration performance should be investigated. In this study, urease (URE) and trypsin (TRY) enzymes were physically immobilized in/on the surface of a polyacrylonitrile (AN69) membrane through layer-by-layer (LbL) self-assembly method using polyethylenemine (PEI) and sodium-alginate (ALG) as cationic and anionic polyelectrolytes respectively. URE, located on the membrane’s surface, degraded urea in a reaction-controlled regime, and its immobilization did not significantly change the hydraulic permeability. On the other hand, the TRY enzyme attached to the membrane’s pores reduced the permeability and degraded the BAPNA in a diffusion-controlled region. In TRY immobilized membranes, the conversion increased linearly with the transmembrane pressure, while in URE immobilized ones, conversion was maximum at 1 bar. Sandwiching the enzymes between two polyelectrolytes resulted in the highest catalytic activities. This configuration maintained most of the URE activity in the long-term filtration, but it did not help prevent TRY’s activity loss. © 2024 by author(s)
Granulation of Hydrometallurgically Synthesized Spinel Lithium Manganese Oxide Using Cross-Linked Chitosan for Lithium Adsorption From Water
No full textA drastic increase in demand for electric vehicles and energy storage systems increases lithium (Li) need as a critical metal for the 21st century. Lithium manganese oxides stand out among inorganic adsorbents because of their high capacity, chemical stability, selectivity, and affordability for lithium recovery from aqueous media. This study investigates using hydrometallurgically synthesized lithium manganese oxide (Li1.6Mn1.6O4) in granular form coated with cross-linked chitosan for lithium recovery from water. Characterization methods such as SEM, FTIR, XRD, and BET reveal the successful synthesis of the composite adsorbent. Granular cross-linked chitosan-coated and delithiated lithium manganese oxide (CTS/HMO) adsorbent demonstrated optimal removal efficiency of 86 % at pH 12 with 4 g/L of adsorbent dosage. The Langmuir isotherm at 25 °C, which showed monolayer adsorption with a maximum capacity of 4.94 mg/g, a better fit for the adsorption behavior of CTS/HMO. Adsorption was endothermic and thermodynamically spontaneous. Lithium adsorption followed the pseudo-first-order kinetic model. © 202
Altitude Shapes Gut Microbiome Composition Accounting for Diet, Thyroid Hormone Levels, and Host Genetics in a Subterranean Blind Mole Rat
No full textThe animal gut microbiome acts as a crucial link between the host and its environment, playing a vital role in digestion, metabolism, physiology, and fitness. Using 16S rRNA metabarcoding, we investigated the effect of altitude on the microbiome composition of Anatolian Blind Mole Rats (Nannospalax xanthodon) across six locations and three altitudinal groups. We also factored in the host diet, as well as host microsatellite genotypes and thyroid hormone levels. The altitude had a major effect on microbiome composition, with notable differences in the relative abundance of several bacterial taxa across elevations. Contrary to prior research, we found no significant difference in strictly anaerobic bacteria abundance among altitudinal groups, though facultatively anaerobic bacteria were more prevalent at higher altitudes. Microbiome alpha diversity peaked at mid-altitude, comprising elements from both low and high elevations. The beta diversity showed significant association with the altitude. Altitude had a significant effect on the diet composition but not on its alpha diversity. No distinct altitude-related genetic structure was evident among the host populations, and no correlation was revealed between the host genetic relatedness and microbiome composition nor between the host microbiome and the diet. Free thyroxine (FT4) levels increased almost linearly with the altitude but none of the bacterial ASVs were found to be specifically associated with hormone levels. Total thyroxine (TT4) levels correlated positively with microbiome diversity. Although we detected correlation between certain components of the thyroid hormone levels and the microbiome beta diversity, the pattern of their relationship remains inconclusive
Quantum Transport Regimes in Quartic Dispersion Materials With Anderson Disorder
No full textMexican-hat-shaped quartic dispersion manifests itself in certain families of single-layer two-dimensional hexagonal crystals such as compounds of groups III-VI and groups IV-V as well as elemental crystals of group V. A quartic band forms the valence band edge in various of these structures, and some of the experimentally confirmed structures are GaS, GaSe, InSe, SnSb, and blue phosphorene. Here, we numerically investigate strictly one-dimensional and quasi-one dimensional (Q1D) systems with quartic dispersion and systematically study the effects of Anderson disorder on their transport properties with the help of a minimal tight-binding model and Landauer formalism. We compare the analytical expression for the scaling function with simulation data to distinguish the domains of diffusion and localization regimes. In one dimension, it is shown that conductance drops dramatically at the quartic band edge compared to the quadratic case. As for the Q1D nanoribbons, a set of singularities emerge close to the band edge, suppressing conductance and leading to short mean-free-paths and localization lengths. Interestingly, wider nanoribbons can have shorter mean-free-paths because of denser singularities. However, the localization lengths sometimes follow different trends. Our results display the peculiar effects of quartic dispersion on transport in disordered systems. (c) 2024 Author(s). All article content, except where otherwise noted, is licensed under a Creative Commons Attribution (CC BY) licens
The Separation Behavior of Tibsub>2/Sub> During Clsub>2/Sub>-free Degassing Treatment of 5083 Aluminum Melt
No full textUtilizing titanium diboride (TiB2) inoculation for grain-refining purposes is a widely established practice in aluminum casthouses and foundries. Since this inoculation is usually implemented jointly with or between routine melt treatment steps ahead of casting, it is important to know whether and how other melt treatment processes affect the fade of TiB2 particles. For the present study, we investigated the influence of degassing process on the separation behavior of TiB2 particles in aluminum melt. Multiple sampling methods were employed and the samples were analyzed via spectrometer analysis. The removal efficiency of TiB2 during the gas-purging process of 5083 aluminum melt was confirmed to be significant over 10 min of treatment time. The rate at which the TiB2 content decays was found to increase with the impeller rotary speed from 400 rounds per minute (rpm) to 700 rpm. The separation rate of TiB2 particles was obtained to be 0.05-0.08 min(-1) by fitting the experimental data. Particle mapping results suggest that the TiB2 particles were separated to a dross layer. The obtained experimental results were used to quantitatively evaluate the conventional deterministic flotation model. The deviation between the conventional model and the experimental data was explained through the entrainment-entrapment (EE) model. Suggestions were made for future analytical and experimental works which may validate the EE model
Trends in Authentication of Edible Oils Using Vibrational Spectroscopic Techniques
No full textThe authentication of edible oils has become increasingly important for ensuring product quality, safety, and compliance with regulatory standards. Some prevalent authenticity issues found in edible oils include blending expensive oils with cheaper substitutes or lower-grade oils, incorrect labeling regarding the oil's source or type, and falsely stating the oil's origin. Vibrational spectroscopy techniques, such as infrared (IR) and Raman spectroscopy, have emerged as effective tools for rapidly and non-destructively analyzing edible oils. This review paper offers a comprehensive overview of recent advancements in using vibrational spectroscopy for authenticating edible oils. The fundamental principles underlying vibrational spectroscopy are introduced and chemometric approaches that enhance the accuracy and reliability of edible oil authentication are summarized. Recent research trends highlighted in the review include authenticating newly introduced oils, identifying oils based on their specific origins, adopting handheld/portable spectrometers and hyperspectral imaging, and integrating modern data handling techniques into the use of vibrational spectroscopic techniques for edible oil authentication. Overall, this review provides insights into the current state-of-the-art techniques and prospects for utilizing vibrational spectroscopy in the authentication of edible oils, thereby facilitating quality control and consumer protection in the food industry. The authentication of edible oils has become increasingly important for ensuring product quality, safety, and compliance with regulatory standards
Audio-magnetotelluric (amt) studies over rajapur hot spring in west coast maharashtra, India
No full textIn the west coast geothermal provinces, the Rajapur hot spring, located in the southern part of western Maharashtra, is well thought to originate from the interaction of meteoric water with the granitic basement. A 3D AMT survey was conducted to determine the geo-electrical structure of the hot spring. Dimensionality analysis carried out by phase tensor analysis reveals complex subsurface 3D structures. 2D and 3D modelling have yielded three distinct resistivity layers in the Rajapur geothermal field. These layers include a moderately resistive surface layer representing weathered Deccan traps having a thickness of about 100 m, a conductive second layer with a thickness of about 100-400 m represents Kaladgi sediments and a deeper high resistive layer (0.5-1.0 km) representing granitic gneisses basement. High conductivity anomaly within the Kaladgi sediments represents a hydrothermal reservoir that is associated with faults/fractures beneath the Deccan Traps
Near-Infrared Emissive Super Penetrating Conjugated Polymer Dots for Intratumoral Imaging in 3d Tumor Spheroid Models
No full textThis study describes the formation of single-chain polymer dots (Pdots) via ultrasonic emulsification of nonionic donor-acceptor-donor type (D-A-D) alkoxy thiophene-benzobisthiadiazole-based conjugated polymers (Poly BT) with amphiphilic cetyltrimethylammonium bromide (CTAB). The methodology yields Pdots with a high cationic surface charge (+56.5 mV +/- 9.5) and average hydrodynamic radius of 12 nm. Optical characterization reveals that these Pdots emit near-infrared (NIR) light at a maximum wavelength of 860 nm owing to their conjugated polymer backbone consisting of D-A-D monomers. Both colloidal and optical properties of these Pdots make them promising fluorescence emissive probes for bioimaging applications. The significant advantage of positively charged Pdots is demonstrated in diffusion-limited mediums such as tissues, utilizing human epithelial breast adenocarcinoma, ATCC HTB-22 (MCF-7), human bone marrow neuroblastoma, ATCC CRL-2266 (SH-SY5Y), and rat adrenal gland pheochromocytoma, CRL-1721 (PC-12) tumor spheroid models. Fluorescence microscopy analysis of tumor spheroids from MCF-7, SH-SY5Y, and PC-12 cell lines reveals the intensity profile of Pdots, confirming extensive penetration into the central regions of the models. Moreover, a comparison with mitochondria staining dye reveals an overlap between the regions stained by Pdots and the dye in all three tumor spheroid models. These results suggest that single-chain D-A-D type Pdots, cationized via CTAB, exhibit long-range mean free path of penetration (approximate to 1 mu m) in dense mediums and tumors. The single chain near infrared (NIR) emissive Pdots with high cationic surface charge enable penetration in dense medium such as tumor spheroids. Both colloidal and optical properties of Pdots make them promising fluorescent probe in bioimaging. imag
Modifying Pickering Polymerized High Internal Phase Emulsion Morphology by Adjusting Particle Hydrophilicity
No full textThis study investigates the use of submicron polymeric particles with varying crosslinking densities as the sole stabilizer for producing Polymerized High Internal Phase Emulsions (PolyHIPE). We establish a direct correlation between the crosslinking density and the hydrophilicity of the polymer particles. The hydrophilicity of these particles significantly influences the morphology and rheology of HIPEs. These differences manifest as various morphological variations in the resulting PolyHIPE templates. It was discovered that by increasing the crosslinker weight percentage in the particles from 0 % to 100 %, PolyHIPEs with semi-open, open, and closed porous structures can be obtained. Furthermore, non-crosslinked particles were observed to dissolve in the continuous phase, acting as macromolecular surfactants that generate small pores akin to surfactant-stabilized structures in PolyHIPE. These findings offer fresh insights into the relationship between particle localization at the interface, HIPE rheology, and the formation of pore throats in Pickering PolyHIPEs, leading to the creation of either closed or open porous networks. Additionally, interfacial rheological results demonstrate that particles synthesized with varying monomer-to-crosslinker ratios exhibit different interfacial elasticities, which are linked to PolyHIPE morphology