Jaw Functional Orthopedics and Cranoficial Growth
Not a member yet
968 research outputs found
Sort by
Vibration characteristics testing and vibration reduction optimization design of four-wheel-drive micro-tiller handlebar assembly
Get PDFMicro-tillers are essential for agricultural operations in hilly and mountainous regions, yet their severe vibrations pose significant health risks to operators, including hand-arm vibration syndrome. This study presents an innovative vibration reduction solution through the installation of a damping spring isolator at the handle-frame connection point. Comprehensive vibration testing revealed that the vertical vibration under tillage conditions reached 2.15 m/s2 RMS, with spectral analysis identifying critical excitation frequencies at 39 Hz, 78 Hz, and 156 Hz. Constrained modal analysis demonstrated that the handle frame's third-order natural frequency of 41.02 Hz risked resonance with the engine’s 39 Hz excitation. The optimized isolator system, designed with a damping ratio of ξ= 0.2, successfully reduced this critical frequency to 34.87 Hz (15 % reduction), effectively avoiding resonance. Field validation showed significant vibration attenuation, with RMS values decreasing by 14.17 % (idle), 17.61 % (no-load), and 23.26 % (tillage), while achieving 19.3 % vibration energy absorption during operation. This research represents the first successful integration of isolation and damping mechanisms for micro-tiller handle frames, providing a cost-effective solution (< 1.5 % of machine cost) that significantly improves operator comfort and addresses long-standing ergonomic challenges in small-scale agricultural machinery. The solution's simple implementation without structural modifications makes it particularly suitable for widespread adoption in developing regions
Enhancing sound absorption of Helmholtz resonance metamaterials with extended microperforated neck
Get PDFTo enhance sound absorption of Helmholtz resonance metamaterials in low frequency region with simple structure and engineering practicability, according to the well-established acoustic absorption theory of micro-perforated panel, a novel designed Helmholtz resonance metamaterial with extended microperforated neck is proposed, and a theoretical modelling method is developed by using the transfer matrix method which is validated by finite element simulation. Both theoretical calculation and finite element simulation results show that sound absorption performance of proposed Helmholtz resonance metamaterial is improved significantly compared to that of Helmholtz resonator with normal neck, and the resonant absorption coefficient is close to 1. The influence of geometric parameters of microperforated neck is also investigated in detail, and some meaningful conclusions are drawn. This work provides a perfect solution for low-frequency noise control with Helmholtz resonance metamaterials
Dual-stator ultrasonic motor achieving 2-DOF linear and rotary motion with single-phase excitation
Get PDFThis study proposes a novel dual-stator linear-rotary ultrasonic motor. The piezoelectric ceramic excites both out-of-plane and in-plane vibration modes within the stator. These distinct vibration modes independently drive the slider (rotor), generating reciprocating linear and rotational motions, respectively. Finite element analysis and laser vibrometer-based vibration testing validated the motor's operational principle. The close agreement between simulated and measured resonant frequencies for both vibration modes, with mere discrepancies of 3 % and 4 %, respectively, underscores the accuracy of the stator’s vibrational characteristics. Subsequently, two stators are fabricated and assembled to the ultrasonic motor prototype. Experimental results demonstrate the motor’s impressive performance, achieving a maximum linear velocity of 265 mm/s and a peak rotational speed of 1600 rpm. Furthermore, the motor delivers a maximum thrust force of 0.18 N and a stalling torque of 1.8 mN·m
Dynamic behaviors and double-frequency synchronization analysis of a dynamic vibration absorption system driven by three co-rotating exciters
No full textThe recovery efficiency of drilling fluid is directly affected by working performance of the vibration screen. Therefore, a newly dynamic vibration absorption system driven by different excitation frequencies is designed through double-frequency synchronization theory to improve the mechanical performance of screening equipment. Firstly, the differential equations of motion of vibration system are deduced by Lagrange method. Then, the theoretical conditions of the system implementing double-frequency synchronization are obtained based on asymptotic method, and stability criterion of the synchronization is revealed according to Routh-Hurwitz criterion. Subsequently, the effects of structure parameters on vibration isolation ability, synchronous state, and stability of synchronization are numerically discussed. Finally, the feasibility of the theoretical method and the obtained results is further verified by simulation and experiment. It is found that the vibration isolation and synchronization performance of the system is influenced by the motor parameters and system structure. The system has the best vibration isolation ability when ωm0= 157 rad/s, which is considered as the best operating frequency of the present vibration system. Meanwhile, when the mass ratio κ between the high-frequency co-rotating rotor and the low-frequency co-rotating rotor is smaller, the absolute value of the stability coefficient Si is larger, and the stability phase difference is smaller, and the system is more stable. The present work can provide theoretical direction for the design of new screening equipment
Modal and optimization analysis of a 12-degree-of-freedom engine mount system considering engine elasticity
No full textThe multi-degree-of-freedom engine mount system presents a coupling issue that significantly impacting its vibration isolation performance. Although the optimization theories for decoupling 6-degree-of-freedom (6-DOF) and 12-degree-of-freedom (12-DOF) engine mount systems are relatively well-developed, previous studies have predominantly focused on engine response and often overlook the impact of car body vibrations. To address this gap, this article conducts an in-depth investigation into how the elasticity of the car body affects the vibration isolation performance of the engine mount system. Initially, the dynamics of the engine mount system are modeled with 6 degrees of freedom, incorporating an elastic base with 9 and 12 degrees of freedom, respectively. The study then analyzes how body elasticity influences the natural frequencies and modal shapes of the engine mount system. Subsequently, the sensitivity of the engine mount system is assessed using Isight analysis to evaluate the three directional stiffnesses of the mount. Finally, the decoupling optimization of the 12-degree-of-freedom engine mount system is performed using the NLPQL (Sequential Quadratic Programming) method. The findings indicate that: (1) considering the car body’s influence directly affects the natural characteristics and decoupling efficiency of the engine mount system; (2) body elasticity in the Z-direction has the greatest impact on the system’s vertical natural frequency; and (3) the NLPQL method effectively enhances the decoupling rate of the engine mount system
Bifurcation and chaos analysis of the floating raft vibration isolation system with quasi-zero-stiffness isolators
No full textThis paper presents an investigation into the nonlinear dynamic behaviors of the floating raft isolation system coupled with quasi-zero-stiffness isolators subject to multiple disturbance sources. First, the coupling effects between the excitation source and isolation system are considered. Also, the floating raft isolation model under multiple excitations and its motion equation are deduced, and then the dynamic responses are mainly investigated by using the techniques of time history diagram, spectrum diagram, phase diagram and Poincaré map, and the bifurcation diagram. Finally, the bifurcations of the mechanical isolation system with different parameters are analyzed through numerical methods, especially the effect of center distance and mass ratio. The result predicts that the floating raft shows an alternate phenomenon of periodic motion, quasi-periodic motion, and chaotic motion when the center distance and mass ratio vary. The motion state of the floating raft vibration isolation system is more sensitive to the mass ratio than to the center distance. The horizontal and rotational response of the system becomes very intense in the chaotic state, and the response amplitudes in the horizontal and vertical directions reach the same order of magnitude. Above all, the dynamic characteristics can provide the theoretic supporting for the dynamics, vibration control and its parametric optimization of the floating raft isolation system coupled with quasi-zero-stiffness isolators. This study will lay down the requirements for the engineering design and application of floating raft isolation equipment in large vessel
Construction of a mathematical model of the motion of a vibrating separator with pneumatic suspension
No full textThe mathematical model of the movement of an arbitrary point of the container of a vibrating separator with a pneumatic suspension is built in the article. For modeling, a vibrating separator with two independently driven unbalances and a pneumatic suspension was chosen, which has a number of advantages over other separators, is characterized by simplicity of construction and maintenance, and low sensitivity to the properties of the medium being separated. The developed unified parameterized model of a vibrating separator can be used by changing its parameters or zeroing them for a wide range of designs of vibrating separators. The use of data from ready-made unified mathematical models allows you to reduce the duration of research and design of vibrating separators, and reduce material costs in general
Estimation of vehicle state based on maximum correntropy square-root cubature Kalman Filter
No full textState estimation of a vehicle is an important direction under the research branch of automotive dynamics, with the aim of determining state variables that reflect vehicle handling stability and other characteristics. In order to solve the problem of poor estimation accuracy caused by heavy tailed non Gaussian noise in traditional state estimation methods, a new filtering algorithm based on the Maximum Correlation Entropy criterion (MCC) and the Square-root Cubature Kalman Filter (MCSCKF) is proposed. On the basis of establishing a nonlinear 3-DOF vehicle model, the yaw rate and the side slip angle as well as the longitudinal velocity of the vehicle were estimated. And the effectiveness of the algorithm was verified through joint simulation with Carsim and Matlab/Simulink. The results show that the MCSCKF algorithm can adapt to complex working conditions and has better accuracy in vehicle state estimation than traditional state estimation algorithms. Meanwhile, the MCSCKF algorithm can effectively reduce the impact of heavy tail non Gaussian noise and improve the accuracy of vehicle state estimation
Permeability test of geotextile-soil system under different sand filling heights
No full textGeotube dams are constructed by stacking geotubes, which are non-homogeneous structures composed of geotextiles and filled sand. Therefore, studying the permeability characteristics of the geotextile-soil system is of great significance for seepage analysis in geotube dams. While the permeability characteristics of geotextiles and filled sand have been extensively studied individually, there has been relatively little research on the permeability characteristics of the geotextile-soil system formed by the combination of geotextiles and soil. In this study, a self-designed permeameter was used to investigate the permeability characteristics of the geotextile-soil system under different sand filling heights. The test results indicate that the permeability coefficient of the geotextile-soil system decreases continuously with the increase in permeation time and eventually stabilizes. The permeability coefficient of the geotextile-soil system increases with the sand-filling height and finally approaches but remains slightly smaller than that of pure sand with the same gradation. The influence of geotextiles on the permeability of the geotextile-soil system is significant within the range of 0 to 5 cm. Additionally, the water permeability of geotextiles affects the permeability performance of the geotextile-soil system. Specifically, a larger porosity corresponds to higher water permeability, and a greater permeability coefficient of the geotextile leads to a higher permeability coefficient of the geotextile-soil system
Determination of optimal drive parameters for high-speed linear systems
No full textThe problem of optimizing the drive design parameters for a high-speed linear system is solved based on minimizing the inertial torque. New analytical expressions are obtained for determining the optimal gear ratio of the intermediate transmission, taking into account the moments of inertia of rotating masses, the carriage mass, and the screw pitch. An optimization problem is proposed to determine the number of gear teeth and the screw pitch by minimizing a function that includes the relative error between the actual and calculated gear ratio, as well as the total number of teeth required to ensure the specified travel speed of a carriage. At the next calculation stage, the number of gear teeth is refined based on the nearest standard screw pitch values. The resulting parameters are evaluated using a transient dynamic analysis according to key kinematic and energy characteristics