Defence Science Journal
Not a member yet
3794 research outputs found
Sort by
A Numerical Study of Penetration in Concrete Targets by Eroding Projectiles of Different Materials
Get PDFNumerical simulations have been performed to examine the effect of three different eroding rod materials on the penetration in concrete targets. Same kinetic energy is delivered to concrete target using cylindrical rods of Aluminium, Iron, and Copper of identical size. Impact velocities have been varied to keep the kinetic energy the same. Penetration characteristics like centerline interface velocity, penetrator deceleration, plastic strain in the target, and energy partitioning during penetration have been studied for the three different penetrator materials. In all three cases, penetration proceeds nearly hydrodynamically. It is seen that even though the steady-state penetration ceases before reaching the hydrodynamic limit, the secondary penetration takes the total penetration beyond the hydrodynamic value. Plastic strain in the target material is a measure of damage beyond the crater produced by penetration. The lateral extent of plastic strain in target is more for Aluminium penetrator compared to the other two. Energy partitioning during penetration provides details of the rate at which energy is entering into the target. Kinetic energy delivered to the target during impact is partitioned into internal energy and kinetic energy of the target. Finally, the influence of target thickness on the extent of plastic strain has been studied. The result shows that Aluminium penetrators inflict maximum damage to targets of finite thickness
Utilisation of High Energy Propellant Waste in Manufacturing of Fired Clay Bricks to Enhance the Acoustic Properties
Get PDFThe disposal and waste management of solid high energy propellant (HEP) is a considerate conservational problem. HEP waste is currently disposed in open or confined burning which may cause environmental hazards. In this paper, we examined and discussed results on recycling of HEP waste into fired clay bricks baked in different orientation. HEP modified bricks with 1.5%, 3% and 5 wt. % HEP waste content were manufactured and tested, and then compared against virgin clay bricks without HEP content. The effect of directional orientation of bricks baked with varying HEP content on acoustic properties were experimented and discussed. The sound transmission loss decreases with increase in HEP waste due to formation of independently closed directional pores. The transmission loss of horizontally baked during firing of bricks is nearly 5dB lower than vertically baked bricks. Results of the experimental studies indicate that HEP waste can be utilised in fired clay bricks and different orientation baking further enhances the acoustic properties
Finite Element Analysis of Experimentally Tested Concrete Slabs Subjected to Airblast
Get PDFSince the last century, concrete has been used to protect structures against intentional or accidental detonation of explosives. Recently, as concerns about terrorist activities and accidents in plants using explosives increase worldwide, the study of the behaviour of this type of material and any civil or military structure under the influence of explosions has increased. Among the lethal effects of explosive devices, which cause greater loads in structural elements is the airblast effect. For this reason, this paper presents a series of airblast finite element (FEM) simulations developed in Abaqus/Explicit®. To validate the computational method, such simulations are geometrically and structurally kept similar to full-scale tests conducted in a blast test area of the Science and Technology Aerospace Department (Brazilian Air Force). Both simulations and tests consisted of seven reinforced concrete slabs with compressive strengths of about 40 to 60 MPa, variable steel reinforcement areas, slab dimensions measuring 1×1 m, and subjected to 2.7 kg of non-confined plastic bonded explosive. The results demonstrated that FEM simulations can predict the rupture of the tested slabs and how the effect occurs, showing a valid method to investigating the response of RC slabs when compared to expensive field tests. Differences in displacements were observed between the results of FEM simulations and blast field tests, mainly caused by the sensitivity of the case studied, limits of computational capacity, and intrinsic variations in the materials and sensors used in the field tests. However, these differences showed an order of magnitude compatible with the safety coefficients used with RC, demonstrating that the method can be used for the design of RC slabs under the effect of airblast
Uninterrupted VPN Connection Service with Mobility Management and Dead Peer Detection
Get PDFThe VPN technology is used to connect client devices securely over unsecured public networks. The Connection handover and Dead Peer Detection (DPD) are the most challenging and important tasks in VPN. In this present article, a solution for connection handover is proposed which covers the pre-authentication with new credentials for a mobile device prior to connection handover. In VPN, a case where such connection handover is failed due to incomplete connection handover or several unusual events which make a VPN client to become offline or dead. To address DPD issues a solution is proposed which includes a Keep Alive Timer (KAT) server at the VPN server side. This proposed solution for DPD is far better than an already existing solution that uses a DNS server for DPD since the DNS server faces several attacks consistently. Thus, the proposed solution for DPD is more secure against such vulnerable attacks
Shock Wave Behaviour of Polymeric Materials for Detonation Waveshapers
Get PDFThis paper discusses the experimental determination of explosive shock attenuation parameters of four different polymers viz., Teflon, Phenol formaldehyde, Polyethylene foam and Polypropylene foam. These polymers are candidate materials for waveshapers in shaped charge warheads. Cylindrical specimens of the polymer materials were subjected to explosive shock loading by the detonation of RDX:Wax (95:5). Shock arrival time was measured using piezo-wafers positioned at known spatial intervals in the specimens. Initial shock velocity, stabilised shock velocity and attenuation constant were determined. These parameters are essential for the design of waveshapers. Foams have better shock attenuating properties compared to solids due to their cellular structure. Polypropylene foam has the highest shock attenuating characteristic among the four materials studied
Multi mode Resonator based Concurrent Triple band Band pass Filter with Six Transmission Zeros for Defence Intelligent Transportation Systems Application
Get PDFA compact and highly selective triple-band bandpass filter (BPF) is designed and presented in this paper. Proposed filter offers low insertion loss, and passband characteristics is achieved by using two coupled MMR multi-mode resonators (MMR1 and MMR2) and an inverted T and circular shape MMRs. The filter operates at frequency 2.43 GHz (Vehicular Communication), 5.91 GHz (ITS band), and 8.86 GHz (satellite communication band). The simulation and measurement results show a minimum insertion loss of 1.6 dB, 0.73 dB, and 2.8 dB for triple-band BPF. The return loss is found to be greater than 13.06 dB, 28.6 dB, and 21.55 dB. It is noted that measurement results are in accordance with the result of electromagnetic simulation. Desired triple-band multi-mode resonators (MMRs) filter characteristics are achieved with six transmission zeroes (TZs). The filter comprises of MMRs which provide small size and control over the spurious frequency. By using a parallel-coupled microstrip line, the first and third passbands are realised. Whereas by using an end-coupled microstrip line, the second passband is recognised. At the input and output ports, the resonator coupling technique is used. By using the anti-parallel microstrip line arrangement, the transmission zero is acquired. The dimensions of the designed filter are 25×16 mm 2
Compact Wideband Microstrip Patch Antenna Design for Breast Cancer Detection
Get PDFThe current breast cancer detection techniques are mostly invasive and suffer from high cost, high false rate and inefficacy in early detection. These limitations can be subdued by development of non-invasive microwave detection system whose performance is predominantly dependent on the antenna used in the system. The designing of a compact wideband antenna and matching its impedance with breast phantom is a challenging task. In this paper, we have designed a compact antenna matched with the breast phantom operating in wideband frequency from 1 to 6 GHz capable to detect the dielectric (or impedance) contrast of the benign and malignant tissue. The impedance of the antenna is matched to a cubically shaped breast phantom and a very small tumor (volume=1 cm3). The antenna is tuned to the possible range of electrical properties of breast phantom and tumour (permittivity ranging from 10 to 20 and conductivity from 1.5 to 2.5 S/m). The return loss (S11), E-field distribution and specific absorption rate (SAR) are simulated. The operating band of antenna placed near the phantom without tumor was found to be (1.11-5.47)GHz and with tumor inside phantom is (1.29-5.50)GHz. Results also show that the SAR of the antenna is within the safety limit
Phase transformation, Mechanical Properties and Corrosion Behavior of 304L Austenitic Stainless Steel Rolled at Room and Cryo Temperatures
Get PDFThe present work investigates the effect of rolling (90% thickness reduction) on phase transformation, mechanical properties, and corrosion behaviour of 304L-austenitic stainless steel through cryorolling and room temperature rolling. The processed steel sheets were characterised through X-ray diffraction (XRD), electron backscattered diffraction (EBSD), and vibrating sample magnetometer (VSM). The analysis of XRD patterns, EBSD scan, and vibrating sample magnetometer results confirmed the transformation of the austenitic phase to the martensitic phase during rolling. Cryorolling resulted in improved tensile strength and microhardness of 1808 MPa and 538 VHN, respectively, as compared to 1566 MPa and 504 VHN for room temperature rolling. The enhancement in properties of cryorolled steel is attributed to its higher dislocation density compared to room temperature rolled steel. The corrosion behaviour was assessed via linear polarisation corrosion tests. Corrosion resistance was found to decrease with increasing rolling reduction in both room temperature rolled and cryorolled specimens
Design of Double Barrier Ceramic Radio Frequency Vacuum Window
Get PDFVacuum windows are an essential part of any radio frequency (RF) system which launches/couples RF power from an atmospheric to a vacuum environment. This paper describes the RF design of a double barrier ceramic coaxial vacuum window. Alumina 99.5% pure is considered as ceramic barrier material while inner and outer conductors are oxygen-free copper. As the initial design approach the thickness, slope, depth of ceramic in the conductor is varied and the performance of the window is studied. The design is optimised to achieve the best insertion loss, return loss response for operating frequency range up to 65MHz
Vacuum Electronic Devices and Applications
Get PDFThis issue of Defence Science Journal (DSJ) contains a collection of nine manuscripts from National Symposium on Vacuum Electronic Devices and Applications (VEDA-2019). Vacuum Electronic Devices and Applications Society organises VEDA symposium/conference/workshop every year at different locations of India. VEDA has established itself as a leading platform for active and innovative research of microwave tubes. It provides a forum for knowledge sharing and exhibition of theoretical and technological development in the general areas of vacuum electronics devices and its system applications. It organises special session to enhance Research Institutes – Industries and Academia Interaction