550909 research outputs found
Sort by
Mechanical Tensile Testing of Hiperco 50A at Cryogenic Temperature
Get PDFHiperco 50A is a highly desired material for use in cryogenic applications, specifically for adiabatic demagnetization refrigerators (ADRs) due to its magnetic field shielding capabilities. Although the alloy has good strength, there is a concern with the material's brittle behavior which is believed to worsen at low temperature based on previous tests. The testing described here investigates the mechanical properties of Hiperco 50A at cryogenic temperature through mechanical tensile testing to failure and evaluation of the failed coupons. The methods and techniques used to determine the elongation, yield strength, ultimate tensile strength, and break strength of the material as well as the results will be presented here
3D Printing and Laser Curing of Al/-Fe2O3 Nanothermites for Gas and Strain Sensing
Get PDFNo abstract availabl
Small Launch Vehicle Sizing Analysis With Solid Rocket Examples
Get PDFSmall launch vehicles are governed by the same physics as large launch vehicles of course, but due to their small size, some aspects and sensitivities become more important and others less. This paper shows semi-empirical correlations to quantify dry mass fraction for both stage and whole vehicle optimization: mass fraction due to density, mass fraction due to thrust-to-weight, and mass fraction due to size reduction. For single-stage optimizations, a stage performance requirement can be met by a locus of mass fraction vs. specific impulse. Based on the above correlations, this alone can recommend a solid or liquid rocket for a stage. Rocket designs of similar technology levels are compared, focusing on where stages become less mass-efficient as they get smaller. The Mars Ascent Vehicle is shown to exemplify a trade between a two-stage solids vehicle and a one- or two-stage liquids vehicle
Design of Experiment for the Measurement of Aerosol Droplet Size Distribution of Temperature-Controlled Thermally Atomized Printed Electronic Inks
Get PDFIn-Space Manufacturing (ISM) centers around NASAs growing need and ability to produce space technologies on demand in space. As the future of long term presence in space and deep space exploration approach, fundamental questions of our dependence on earth resupply to Low Earth Orbit (LEO) remain unanswered. ISM is leading various effort to evaluate the feasibility of producing essential spares and redundant parts on demand to enable a sustainable space-based supply chain model for part resupply. Among the parts and systems being considered, Avionics form the neural network of modern day aircraft and space vehicles providing a wealth of information ranging from Guidance, Navigation, and Control (GN&C) systems to on board Environmental Control and Life Support (ECLS) systems. Recent advances in the use of Aerosol Jet Technology to print Avionics components ranging from electrical traces on a circuit board to complex transistors and sensors raise the possibility of using such technology to reproduce or recreate electronic parts on demand with the help of custom electronics 3D printers. The challenge herein lies within the ability of such printers to generate and deposit an aerosol of electronic material utilizing processes independent of or enhanced by gravity to ensure controllably identical or improved behavior of the aerosol in an International Space Station (ISS) laboratory and on the ground. The behavior as well as the hazards and properties associated with such aerosols in a microgravity environment must be understood well in order to merit a feasible approach to utilizing them for manufacturing in space. In this report, we outline the experimental setup of a modified conventional vaping device to be used as the ideal gravity independent thermal atomization mechanism to generate aerosol. Our objective is to identify the ideal mass, density, and volume of our aerosolized droplets of ink to conclude that there exist a threshold of aerosolized ink droplet sizes that are indeed independent of the effects of gravity and remain stable after atomization. We use a Malvern Spraytec Spray Particle Size Analyzer to perform real-time laser diffraction measurement of our ink droplets during atomization. The droplet size between conductive ink, dielectric ink and vegetable glycerin have been measured and contrasted. Furthermore, the mechanism of thermal atomization versus traditional pneumatic and ultrasonic atomization for operation in microgravity have been explored
NASA Marshall Space Flight Center Human Factors Engineering Analysis of Various Hatch Sizes and Associated Safety Impacts
Get PDFThe NASA Docking System (NDS) is a 31.5-inch (800-millimeter)-diameter circular hatch for astronauts to pass through when docked to other pressurized elements in space or for surface egress. The NDS is utilized on the Orion Spacecraft and has been implemented as the International Docking System Standard (IDSS). The EV74 Human Factors Engineering (HFE) Team at NASAs Marshall Space Flight Center (MSFC) conducted human factors analyses with various hatch shapes and sizes to accommodate for all astronaut anthropometries, task comfort, and task safety. The 32-inch hatch is too small and a bigger hatch size would better accommodate most astronauts and prove to be safer for daily pass-throughs. To conduct human factors analyses, four participants were gathered based on anthropometry: 1st female, 5th female, 95th male, and 99th male
Land Long Term Climate Data Record
Get PDFAVHRR data record is well alive and continue to improve and be used by a large land user community.Most of the improvement are due to the overlapping with MODIS Aqua, Terra.We recommend operating missions as long as possible to enable overlap of at least a few years (especially for applications)
Electron Beam Welding of Pure Tungsten Hex Cans for Nuclear Thermal Propulsion Engines
Get PDFNuclear thermal propulsion (NTP) is an in-space propulsion method currently being developed at the NASA Marshall Space Flight Center (MSFC). NTP systems are a high specific impulse (7501,100 s), high thrust (15,000250,000 lbf ) method of propulsion which have the potential to allow for faster transit times when optimizing for high V. In the nuclear rocket engine, the heat from the nuclear fission reaction is transferred to a low molecular mass propellant (such as hydrogen). Hot propellant is expanded through a nozzle to generate thrust. Development of ceramic metal (cermet) fuel systems for NTP applications is currently ongoing at MSFC. In cermet fuel systems, ceramic fissile fuel particles such as uranium nitride or uranium dioxide are dispersed within a net-shaped, high-density structural matrix. The composite material is cladded by a protective metal structure to make up an NTP fuel element. Cladding materials must be able to withstand the demanding operating conditions required of the engine as well as retain a hermetic seal to allow for retention of fuel element structural integrity, prevent hydrogen attack or migration of the ceramic fuel, and limit release of fission products during operation. For NTP applications, tungsten is a prime material for both the metal matrix and cladding in cermet fuel systems because of its high melting point, high temperature strength, and compatibility with hot hydrogen. If a weld in tungsten with the capability of holding a hermetic seal is achievable, tungsten becomes a strong candidate for NTP applications. This Technical Memorandum focuses on determining the weldability of pure tungsten using electron beam welding (EBW). Tungsten appears well suited for NTP applications, but it has a high ductile to brittle transition temperature (DBTT) dependent upon chemical composition, structure/stress distribution, and mechanical conditions. Therefore, it is highly subject to brittle fracture. Because of its high susceptibility to brittle fracture, it is very difficult to weld. EBW was chosen for joining pure tungsten because of its low heat input compared to gas tungsten arc welding. Reduced heat input can be directly correlated with an increase in ductility of a tungsten weld. EBW is a high energy density welding process in which a stream of electrons penetrates a weld joint in a deep, narrow spike in contrast to a broad gas tungsten arc weld pool. The investigation initially focused on EBW of tungsten plates of both 0.01 in and 0.03 in thickness to determine if EBW could weld pure tungsten without the presence of visual defectsparticularly crackingin the welds. Variation in the weld procedure and post-weld heat treatment (PWHT) was used to improve the surface appearance of flat EBWs on a pure tungsten sheet. The investigation moved on to weld 0.05-in-thick hexagonal tungsten cans with a weld joint thickness of 0.025 in. The goal for welding the pure tungsten hex cans was to avoid any visual surface defects and generate a weld capable of a hermetic seal. This proved difficult. Cold welds commonly exhibited porosity that leaked air. Hot welds exhibited cracks, typically observed immediately after welding. Later welds were preheated to increase ductility and decrease the likelihood of through-thickness cracking. PWHT was used to arrest microcrack growth both in the flat weld samples and hexagonal weld samples