550909 research outputs found
Sort by
Patch Plate Materials Compatibility Assessment
Get PDFLunar dust proved to be a greater problem during the Apollo missions than was originally anticipated. The highly angular, charged dust particles stuck to seals, radiators, and visors; clogged mechanisms; and abraded space suits. As reported by Apollo 12 astronaut Pete Conrad "We must have had more than a hundred hours suited work with the same equipment, and the wear was not as bad on the training suits as it is on these flight suits in just the eight hours we were out.". Dust clinging to surfaces was also transport-ed into habitable spaces leading to lung and eye irritation of the astronauts. The Apollo astronauts were on the Lunar surface less than 24 hours and experienced many dust related problems. With the Artemis program, we are planning longer stays on the surface, with more activities that have the potential to put the astronauts and equipment in contact with greater quantities of Lunar dust. The success of these missions will depend on our understanding of material interactions with Lunar dust and the development of ways to mitigate dust effects in cases where exposure to dust will lead to failure of components, unacceptable loss of power or thermal control, unacceptable loss of visibility, or health issues. Through the Lunar Surface In-novation Initiative (LSII), we are initiating a Patch Plate Materials Compatibility Assessment project. The overall goal of the three year project is to develop passive approaches to mitigate Lunar dust adhesion to surfaces for technologies that are currently at TRL levels 2-3 to bring them to TRL level 5 through ground-based assessment, culminating in a demonstration flight experiment on a Commercial Lunar Payload Services (CLPS) lander in 2022-2023. This paper discusses the detailed technical objectives and approach for this project. References: Gaier, J.R. "The Effects of Lunar Dust on EVA Systems During the Apollo Missions," NASA/TM-2005-213610/REV1, (2005), Apollo 12 Technical Crew Debriefing, December 1, 1969, pp. 10-54
Advanced Unmanned Aerial Vehicles for Improved Communications
Get PDFReestablishing communication channels is one of the most important yet time-consuming procedures to carry out following a natural disaster. After Hurricane Katrina impacted Louisiana in 2005, more than 60% of networks were still down 3 weeks after the event.1 In 2017, when Hurricane Mara devastated Puerto Rico, 95% of cellular sites failed island-wide, leaving many civilians disconnected for months.2 One viable approach to this challenge is increasing the capabilities of Unmanned Aerial Vehicles (UAVs), commonly known as drones, which could provide sustained communication outlets in hard-to-access areas while emergency response efforts are underway
Vision for Cross-Center MSBE Collaboration on the Gateway Program
Get PDFModel-Based Systems Engineering (MBSE) can be a challenge when there is only one modeler and one model involved. For the Gateway Program, due to its unique acquisition approach, the modeling efforts involve multiple NASA centers with each developing their own models. Every additional model to be integrated compounds the difficulties, necessitating stronger ontologies and explicitly defined interfaces between models. To help facilitate this integration, a vision of collaboration between centers is in its beginning stages. This vision includes looking at models as systems themselves and developing their own use cases, requirements and interfaces between each of them. The goal of this presentation is to share the Gateway Program's cross-center vision for model collaboration, the lessons learned in developing and implementing that vision for the various system engineering products needed to satisfy life cycle review criteria and how treating models as systems helped in these efforts
Core Losses in Co-Rich Inductors with Tunable Permeability
Get PDFHigh frequency, low loss power systems enable electrified aircraft propulsion. Filter inductors that reduce noise in high current systems can account for 50% of the motor drive mass. Efficient inductor cores with tunable permeability reduce system mass by producing less heat, that removes heat sink mass. Requirements for filter inductors vary based on the chosen topology, but all inductor cores must operate below saturation levels. As the saturation flux density is limited (less than ~2 T), high differential current applications require cores with low relative permeabilities. The large induced anisotropies possible in Co-rich metal amorphous nanocomposite materials enables gapless inductors with relative permeabilities down to ~20. These materials have fine grain size ~8nm with a faulted, close packed structure. The impact of different processing methods on core losses are presented along with comparison to other low permeability soft magnetic materials
Searching for Hyperspectral Optical Proxies to Aid Chesapeake Bay Resource Managers in the Detection of Poor Water Quality
Get PDFShellfish aquaculture is a growing industry in the Chesapeake Bay. As population grows near the coast, extreme weather events cause a greater volume of pollutant runoff from impervious surfaces and agricultural lands. Resource managers who monitor shellfish beds need reliable information on a variety of water quality indicators at higher frequency than is possible through field monitoring programs and at a higher level of detail than current satellite products can provide. Although many factors causing degraded water quality that can impact human health are not currently discernable by traditional multispectral techniques, hyperspectral imagery offers a new opportunity to detect phytoplankton communities associated with harmful algal blooms and biotoxin production. Together with resource managers in their routine monitoring of sites around the bay from small boats, we have been exploring remotely sensed optical proxies for the detection of harmful algal blooms and sewage. Early warning by remote sensing could guide sampling and improve the efficiency of shellfish bed closures, ultimately improving health outcomes for humans and animals. An extensive network of routine sampling by Chesapeake Bay Program managers makes this is an ideal location to develop and test future satellite data products to support management decisions. Next generation hyperspectral measurements from the future Plankton Aerosol Cloud ocean Ecosystem (PACE) mission at nearly daily frequency, combined with the potential of higher spatial resolution from the Surface Biology and Geology (SBG) observing system recommended in the recent Decadal Survey, along with high frequency observations from the newly selected Geostationary Littoral Imaging and Monitoring Radiometer (GLIMR) Earth Venture Instrument make this a critical time for defining the needs of the aquaculture and resource management community to save lives, time, and money
A Bi-Exponential Repair Algorithm for Radiation-Induced Double-Strand Breaks: Application to Chromosome Aberrations
Get PDFChromosome aberrations (CAs) are one of the effects of radiation exposure and are used as a biomarker. A new simulation program, named RITCARD (Radiation induced tracks, chromosome aberrations, repair, and damage) was developed to simulate radiation-induced CA. RITCARD is used with the program RITRACKS (Relativistic Ion Tracks), which simulates the radiation tracks. The restitution kinetics algorithm presented here is a significant improvement over the one used in the first version. Simulations of radiation-induced CA were performed for several ion types and mixed irradiation fields. These simulations will be useful to help interpreting experiments of galactic cosmic rays (GCR) simulator