Fine Chemical Technologies (E-Journal) / Тонкие химические технологии
Not a member yet
1367 research outputs found
Sort by
ОПРЕДЕЛЕНИЕ СТРУКТУРЫ ПРИМЕСЕЙ В ТРИЭТИЛЕНГЛИКОЛЕ МЕТОДАМИ ЯМР И ВЭЖХ-МС/МС ВЫСОКОГО РАЗРЕШЕНИЯ
The process of natural gas drying leads to accumulation of unstudied organic impurities in the used absorbent solutions. These impurities reduce the drying capacity of triethylene glycol. In order to increase the effectiveness of installations for drying natural gas it is necessary to purify triethylene glycol from the accumulated impurities. The absence of information on the structure and properties of these impurities considerably complicates the purification of the absorbent solutions. In this study the structures of impurities accumulated in triethylene glycol were determined by NMR and high resolution mass-spectrometry coupled with chromatography (HPLC-MS/MS). The obtained results will enable to improve the existing methods for the purification of the working solutions of the absorbent.В процессе абсорбционной осушки природного газа в используемых растворах абсорбентах накапливаются неизученные органические примеси, которые снижают осушающую способность триэтиленгликоля. Для повышения эффективности функционирования установок осушки природного газа необходимо периодически очищать триэтиленгликоль от накопливающихся загрязнителей. Отсутствие информации о структуре и свойствах этих примесей существенно усложняет процедуру очистки рабочих растворов абсорбента. В работе были установлены структуры соединений, накапливающихся в триэтиленгликоле, методами ЯМР и ВЭЖХ-МС/МС высокого разрешения. Полученные результаты позволят усовершенствовать существующие способы очистки рабочих растворов абсорбента
НАДЕЖНОСТЬ ХИМИКО-ТЕХНОЛОГИЧЕСКИХ СИСТЕМ
A significant part of the gross domestic product is lost because of hitches followed by long downtime periods in industrial systems. This is a common problem in the industry of developed nations. Analysis of causes of this phenomenon allows developing a conception of solving this problem and suggesting a method of studying the reliability (working capacity) of chemical-engineering systems (CES). In this article we prove the need for technological reliability analysis tools in prefeasibility study to estimate the potential working capacity of the technology and to avoid the large costs of starts and stops.В промышленности наблюдается неприятное явление, заключающееся в том, что значительная часть ВВП теряется из-за внезапных остановок и последующих долгих простоев производящих промышленных систем. Анализ причин данного явления позволил сформировать концепцию решения проблемы и предложить метод исследования надежности (работоспособности) химико-технологических систем (ХТС). В данной статье доказывается необходимость применения инструментария анализа технологической надежности на этапе до проектирования производства для оценки потенциальной работоспособности технологии и исключения значительных расходов ресурсов на запуски и остановки
КОМПЛЕКСНЫЕ СОЕДИНЕНИЯ ХЛОРИДОВ И БРОМИДОВ НЕКОТОРЫХ ЛАНТАНИДОВ С АЦЕТАМИДОМ: СИНТЕЗ И СТРОЕНИЕ
The aim of the this work is the synthesis and study (IR, single crystal XRD, DTG) of complex compounds of chlorides and bromides of lanthanum, neodymium, holmium, and erbium with acetamide [Ln(AA)4(H2O)4]Cl3·H2O (Ln = La, Nd, Ho, Er ) and [La(AA)4(H2O)4]Br3·H2O. Ligands (Ln) coordination occurs through the oxygen atoms, and the coordination polyhedra of the Ln atoms are distorted tetragonal antiprisms or two-capped trigonal prisms (CN = 8). All the studied complexes are characterized by a developed system of hydrogen bonds with the bromide or chloride ions (and outer-sphere water molecules) in the cavities of the structure formed by the complex cations. The features of the complexes thermal decomposition are discussed.Представлены данные по синтезу и исследованию (ИКС, РСА, ДТГ) строения ранее не описанных комплексных соединений хлорида и бромида лантана, хлоридов неодима, гольмия и эрбия с ацетамидом (AA) состава [Ln(AA)4(H2O)4]Cl3·H2O (Ln = La, Nd, Ho, Er ) и [La(AA)4(H2O)4]Br3·H2O. Методом ИК-спектроскопии показано, что в кристаллах комплексов координация лигандов (вода или ацетамид) металлом осуществляется через атомы кислорода (КЧ 8). Для всех комплексов форма координационного полиэдра промежуточная между додекаэдром и тригонально-призматической с двумя дополнительными вершинами над центрами двух прямоугольных граней. Галогенид-ионы не участвуют в образовании внутренней координационной сферы комплексов; в кристаллах присутствует дополнительно внешнесферная молекула воды. Рассмотрены особенности структуры кристаллических ацетамидных производных галогенидов редкоземельных элементов и характер их термического разложения
ВОЗМОЖНОСТИ ОПРЕДЕЛЕНИЯ ЛЯМБДА-ЦИГАЛОТРИНА В МИКРОКАПСУЛИРОВАННЫХ ИНСЕКТИЦИДНЫХ КОМПОЗИЦИЯХ
The determination of the title compound in the model microencapsulated insecticidal tools is considered, as well as the ability to conduct analysis in mixtures with other encapsulated means on the basis of a pyrethroid (cypermethrin, deltamethrin, tetramethrin, permethrin, phenothrin, transfluthrin) and phosphorus-containing derived insecticidal substances (chlorpyrifos). The conditions of direct analytical determination and the stage of sample preparation with the previously described methods are adapted. The content of lambda-cyhalothrin together with cypermethrin in microencapsulated compositions is determined by spectrophotometric method taking into account the absorption of trace contaminants - technical substances and building blocks of microcapsules (phospholipids). RP HPLC method shows the possibility of separate determination of lambda-cyhalothrin and several pyrethroids (except for cypermethrin), and chlorpyrifos, in the hypothetical compositions in a joint encapsulating order to obtain a highly active insecticide that enable overcoming the resistance of insects to a number of inactive substances.Рассмотрены методы определения в модельных инсектицидных микрокапсулированных средствах титульного соединения, а так же возможность проведения анализа в смесях с другими инкапсулированными средствами на основе пиретроидных (циперметрин, дельтаметрин, тетраметрин, перментрин, фенотрин, трансфлутрин) и фосфорсодержащей (хлорпирифос) инсектицидных субстанций. Адаптированы условия проведения непосредственно аналитического определения и стадии пробоподготовки, с ранее приведенными методами. Реализовано установление содержания лямбдацигалотрина совместно с циперметрином в микрокапсулированных композициях спектрофотометрическим методом, учитывающим поглощение микропримесей технических субстанций и строительных блоков микрокапсул (фосфолипидов). Методом ОФ ВЭЖХ показана возможность раздельного определения лямбдацигалотрина и ряда пиретроидов (за исключением циперметрина), а так же хлорпирифоса, в гипотетических композициях при совместном инкапсулировании с целью получения высокоактивных инсектицидных препаратов, позволяющих преодолевать резистентность насекомым к ряду малоактивных веществ
ТЕХНОЛОГИЧЕСКОЕ РАЗВИТИЕ ФГУП «РосРАО» В РАМКАХ СОЗДАНИЯ ОТРАСЛЕВОЙ ИНФРАСТРУКТУРЫ ПЕРЕРАБОТКИ, КОНДИЦИОНИРОВАНИЯ И ХРАНЕНИЯ РАДИОАКТИВНЫХ ОТХОДОВ
This article describes promising technological solutions for the processing, storage and transportation of radioactive waste (RW) implemented by a leading Russian enterprise specializing in the field of radioactive waste management. Federal State Unitary Enterprise "RosRAO" performs nationallevel tasks to ensure nuclear, radiation and environmental safety in the treatment of all types of radioactive waste. To date, FSUE "RosRAO" has a number of ready-made solutions aimed at saving resources while maintaining the radiation and environmental safety by reducing logistics costs due to using large containers for transportation and storage; maximum recycling of waste at the site of its formation or interim storage with the help of mobile systems; creation and operation of easily erected facilities for temporary storage of solid radioactive waste before transferring it for conditioning or disposal. In recent years, we completed a number of major projects focused on improving the radioecological situation on the territory of Russia. The Regional Centre for conditioning and long-term storage of radioactive waste, largest in Russia, was put into operation in Sayda Guba in Murmansk region. Works for state needs were performed to bring radiationhazardous objects to a safe state and to reclaim territories of the Russian Federation subjects exposed to radiation as a result of past activities in the Trans-Baikal and Stavropol territories, Kirov, Moscow, Ivanovo and Orenburg regions
ПОЛУЧЕНИЕ И ФИЗИЧЕСКИЕ СВОЙСТВА ОПАЛОВЫХ МАТРИЦ С НАНОЧАСТИЦАМИ ОКСИДОВ Fe И Ti
The article considers specific features of the formation of nanocomposites based on the lattice packing of SiO2 nanospheres (opal matrices) with clusters of titanium and iron compounds (FeTiO3, FeTi2O5, TiO2, Fe2O3) embedded into nanopores between spheres. For the formation of the nanocomposites samples of opal matrices with the sizes of single-domain regions > 0.1 mm3 were used. The diameter of the SiO2 nanospheres was ~260 nm. Nanocomposites with the volume > 1 cm3 and 10-15% of interspherical nanospacing filled by crystallites of titanium and iron compounds were obtained. The composition and structure of the nanocomposites were studied by electron microscopy, X-ray diffraction and Raman spectroscopy. The dependence of the composition of the synthesized materials on the conditions of their preparation is shown. Results of measurements of the frequency dependences (within the range 1 MHz - 3 GHz) of the magnetic and dielectric characteristics of the obtained nanostructures are presented. Hysteresis loops were studied for the obtained samples.Рассмотрены особенности формирования нанокомпозитов на основе решетчатых упаковок наносфер SiO2 (опаловых матриц), содержащих в межсферических полостях кластеры соединений титана и железа (FeTiO3, FeTi2O5, TiO2, Fe2O3). Для формирования нанокомпозитов использовали образцы опаловых матриц с размерами монодоменных областей > 0,1 мм3, диаметр наносфер SiO2 составлял ~260 нм. Получены нанокомпозиты объемом > 1 см3 с заполнением 10-15% объема межсферических полостей кристаллитами соединений титана и железа. Изучены состав и строение нанокомпозитов с использованием электронной микроскопии, рентгеновской дифрактометрии и спектроскопии комбинационного рассеяния света. Показана зависимость состава синтезированных веществ от условий их получения. Представлены результаты измерений частотных (в диапазоне 1 МГц - 3 ГГц) зависимостей магнитных и диэлектрических характеристик полученных наноструктур. Проведены исследования петель гистерезиса для полученных образцов
МНОГОКОМПОНЕНТНЫЕ СИСТЕМЫ С ТРЕХФАЗНЫМ РАССЛАИВАНИЕМ
A review of scientific publications that describe systems with a three-phase splitting region is presented. Mechanisms of a three-phase splitting region formation are shown. All the suggested classifications of diagrams with a three-phase splitting region are presented. Methods for studying the evolution of a three-phase splitting region are described. Problems connected with the mathematical modeling of liquid - liquid - liquid equilibrium are considered. The ability of mixtures to form three-phase splitting regions and opportunities of separating such mixtures by special methods is analyzed. A list of known systems with three and more liquid phases is presented.В работе представлен обзор научных публикаций, посвященных исследованию систем с трехфазным расслаиванием, образованных соединениями различных классов. Рассмотрены механизмы образования областей трехфазного расслаивания. Приведены примеры классификаций диаграмм расслаивания многокомпонентных систем и описаны подходы к исследованию эволюции области трехфазного расслаивания. Также уделено внимание проблемам моделирования равновесия жидкость-жидкость-жидкость и использованию свойства смеси образовывать области трехфазного расслаивания для разделения смесей экстракционными методами и методами, сочетающими ректификацию и расслаивание. Приведен список известных на сегодняшний день систем с тремя и более жидкими фазами
МОДИФИКАЦИЯ ЭПОКСИАМИННЫХ ПОЛИМЕРОВ ОЛИГОГЕКСАМЕТИЛЕНГУАНИДИНАМИ
Methods of introducing a water-soluble biocide modifier, oligohexamethyleneguanidine hydrochloride, into epoxy-amine systems were studied. The obvious way is the introduction of the modifier in the waterborne epoxy-amine systems. However, this leads to cured systems with reduced mechanical properties. Introduction of oligohexamethyleneguanidine hydrochloride solutions in organic solvents into epoxy-amine systems allows obtaining a homogeneous system, but their application is limited by the presence of a volatile solvent. Finally, introduction of oligohexamethyleneguanidine hydrochloride solutions in a water-soluble amine curing agent into epoxy-amine systems has good prospects. It is shown that the analyzed modifier has good solubility in ethylenediamine, but poor solubility in oligooxypropylenediamine. It was found that the modifier is capable of interacting chemically with epoxy resins at 22°C to form an elastic insoluble material. In an epoxy-amine system with a more active hardener (ethylenediamine) oligohexamethyleneguanidine hydrochloride acts as a plastifier (flexibilizer). This significantly reduces the glass transition temperature of the matrix (from 53 to 37ºC)
ОСОБЕННОСТИ ЛИОФИЛИЗАЦИИ НАНОЛИПОСОМАЛЬНОГО ПРЕПАРАТА
The conditions of lyophilization of nanoliposomes with encapsulated gentamicin (liposomal gentamicin) were studied. A mode of its safe lyophilization was suggested. A program for eliminating adverse factors was developed. It includes smooth increase of temperature from -70°C (freezing temperature) to room temperature (22±2)°C and gradual reduction of vacuum from 30 to 10 Pa without jumps and drops. The characteristics of the labile nanoliposomal drugs were not lost. The suggested program consisted of 10 steps allowing computer control to attain a slow and uniform increase in the temperature of the frozen product. The precise control of pressure in the chamber was provided by a system of automatic regulation of vacuum supplied with the equipment. After the rehydration the lyophilized preparations completely restored their original shape and properties.Изучены условия лиофилизации нанолипосом с инкапсулированным гентамицином (липосомальный гентамицин). Предложен мягкий технологический режим лиофилизации по разработанной программе автоматического управления параметрами. Предлагаемая программа состоит из 10 шагов для достижения медленного и равномерного повышения температуры замороженного продукта. Для устранения неблагоприятных факторов в программе, предусмотрено плавное увеличение температуры от -70°С (температура замораживания) до комнатной температуры (22±2)°С и постепенное снижение вакуума от 30 до 10 Па без скачков и перепадов. Точный контроль давления в камере обеспечивается системой автоматического регулирования вакуума, входящего в комплект поставки оборудования. После регидратации лиофилизированные препараты полностью восстановили свою первоначальную форму и свойства
ВЗАИМОСВЯЗЬ ДИАГРАММЫ ФАЗОВОГО РАВНОВЕСИЯ И СТРУКТУР СХЕМ РАЗДЕЛЕНИЯ МНОГОФАЗНЫХ ЧЕТЫРЕХКОМПОНЕНТНЫХ СМЕСЕЙ
In this work the structures of phase equilibrium diagrams of multiphase four-component systems n-hexane (n-heptane, n-octane) - cyclohexane - furfural - water were investigated. The systems are characterized by the existence of areas of three-phase separation. On the basis of the obtained data the synthesis of feasible variants of separation schemes was carried out, rational modes of functioning of each column were found, the energetically favorable variant was chosen. It was found that the use of preliminary phase separation in systems with n-hexane and n-octane is power-efficient, and the profit in case of the octane system (equimolar mixture) in comparison with the application of the first predetermined separation at the first stage is more than 25%. Certain difficulties (the high values of columns effectiveness: 60 and 40 theoretical plates) upon the separation of the hexane and heptane systems are due to the similar volatilities of n-hexane (n-heptane) and cyclohexane in the vicinity of the point of pure alkane.В настоящей работе исследованы структуры диаграмм фазового равновесия многофазных четырехкомпонентной систем: н-гексан (н-гептан, н-октан) - циклогексан - фурфурол - вода, характеризующихся наличием областей трехфазного расслаивания. На основе полученных данных: проведен синтез возможных вариантов схем разделения, подобраны рациональные режимы функционирования каждой из колонн, выбран энергетически выгодный вариант. Установлено, что использование предварительного расслаивания в системах с н-гексаном и н-октаном является энергоэффективным, причем выигрыш в случае октановой системы (эквимолярная смесь) по сравнению с применением первого заданного разделения на первой стадии составляет более 25%. Определенные трудности (высокие значения эффективностей колонн: 60 и 40 теоретических тарелок) при разделении гексановой и гептановой систем связаны с близкими летучестями н-гексана (н-гептана) и циклогексана в окрестности точки чистого алкана