JEOS:RP - Journal of the European Optical Society Rapid publications
Not a member yet
545 research outputs found
Sort by
Absorbance properties of gold coated fiber Bragg grating sensor for aqueous ethanol
Full text linkOptical Fiber Bragg Grating (FBG) is commonly deployed as a wavelength selective filter in telecommunication as well as to detect physical changes such as pressure, temperature and strain in sensing applications. This paper presents an investigation of FBG as a chemical sensor towards ethanol in aqueous solution. Telecommunication standard single mode FBGs were coated with different thicknesses of thin gold films via sputtering deposition method. The combination of Bragg gratings and gold film enhances the evanescent wave on the surface of the optical fiber. It was found that the FBG coated with 50 nm gold layer exhibits the strongest response towards water with varying concentrations of ethanol. The sensor shows 55% change in absorbance levels when the concentration of ethanol is increased from 0 to 99.7% in water
Effect of surface roughness on optical heating of metals
Full text linkHeating by absorption of light is a commonly used technique to ensure a fast temperature increase of metallic samples. The rate of heating when using optical heating depends critically on the absorption of light by a sample. Here, the reflection and scattering of light from UV to IR by surfaces with different roughness of iron-based alloy samples (Fe, 1 wt-% Cr) is investigated. A combination of ellipsometric and optical scattering measurements is used to derive a simplified parametrisation which can be used to obtain the absorption of light from random rough metal surfaces, as prepared through conventional grinding and polishing techniques. By modelling the ellipsometric data of the flattest sample, the pseudodielectric function of the base material is derived. Describing an increased roughness by a Maxwell-Garnett model does not yield a reflectivity which follows the experimentally observed sum of scattered and reflected intensities. Therefore, a simple approach is introduced, based on multiple reflections, where the number of reflections depends on the surface roughness. This approach describes the data well, and is subsequently used to estimate the fraction of absorbed energy. Using numerical modelling, the effect on the heating rate is investigated. A numerical example is analysed, which shows that slight changes in roughness may result in big differences of the energy input into a metallic sample, with consequences on the achieved temperatures. Though the model oversimplifies reality, it provides a physically intuitive approach to estimate trends
The influence of the aspheric profiles for transition zone on optical performance of human eye after conventional ablation
Full text linkThe analysis in the impact of transition zone on the optical performance of human eye after laser refractive surgery is important for improving visual correction technology. By designing the ablation profiles of aspheric transition zone and creating the ablation profile for conventional refractive surgery in optical zone, the influence of aspheric transition zone on residual aberrations was studied. The results indicated that the ablation profiles of transition zone had a significant influence on the residual wavefront aberrations. For a hyperopia correction, the profile #9 shows a larger induced coma and spherical aberration when the translation of the centre of pupil remains constant. However, for a myopia astigmatism correction, the induced coma and spherical aberration in profile #1 shows relatively larger RMS values than those in other profiles. Therefore, the residual higher order aberrations may be decreased by optimizing ablation profiles of transition zone, but they cannot be eliminated. In order to achieve the best visual performance, the design of ablation pattern of transition zone played a crucial role
Controllable 3D display system based on frontal projection lenticular screen
Full text linkA novel auto-stereoscopic three-dimensional (3D) projection display system based on the frontal projection lenticular screen is demonstrated. It can provide high real 3D experiences and the freedom of interaction. In the demonstrated system, the content can be changed and the dense of viewing points can be freely adjusted according to the viewers’ demand. The high dense viewing points can provide smooth motion parallax and larger image depth without blurry. The basic principle of stereoscopic display is described firstly. Then, design architectures including hardware and software are demonstrated. The system consists of a frontal projection lenticular screen, an optimally designed projector-array and a set of multi-channel image processors. The parameters of the frontal projection lenticular screen are based on the demand of viewing such as the viewing distance and the width of view zones. Each projector is arranged on an adjustable platform. The set of multi-channel image processors are made up of six PCs. One of them is used as the main controller, the other five client PCs can process 30 channel signals and transmit them to the projector-array. Then a natural 3D scene will be perceived based on the frontal projection lenticular screen with more than 1.5 m image depth in real time. The control section is presented in detail, including parallax adjustment, system synchronization, distortion correction, etc. Experimental results demonstrate the effectiveness of this novel controllable 3D display system
Low loss GaN waveguides for visible light on Si substrates
Full text linkIn this work, we present the fabrication and the characterization of an optical waveguide made of AlN and GaN layers grown by MBE on a Si(111) substrate. For the fundamental mode at 633 nm, the propagation losses are in the order of 2 dB/cm, which is a good number for SC waveguides at this wavelength. The propagation losses dramatically increase with the mode order. A careful comparison of measurements and modeling of the complete structure allows identifying the part of the losses due to absorption in the Si substrate, and showing that propagation losses could be further reduced by using well chosen SOI substrates
Ritchey–Common test for a 1.5 m–diameter flat mirror
Full text linkThis study intensively investigates the Ritchey–Common test to enable high-precision measurement of a plane mirror figure with a diameter of 1.5 m. We present a method for separating the adjustment error combined with tested data and the least–square method. We also use the transformation relationship of coordinates and amplitude between the test system pupil plane and the flat mirror to calculate the flat mirror surface error. Ritchey–Common test is conducted on a 100 mm–diameter plane mirror. Results prove that the algorithm can effectively isolate the adjusting–error effect. Compared with the direct test results from interferometer, the RMS calculation accuracy of the algorithm is better than λ/100 (λ = 0.6328 µm). Accordingly, we build a Ritchey–Common test light path for the 1.5 m plane mirror. After analyzing the factors affecting the experiment results, we obtain the surface PV value of 0.391 l and RMS of 0.0181 λ. Finally the test achieves full aperture detection for a large–diameter plane mirror surface
Study of single mode tapered fiber-optic interferometer of different waist diameters and its application as a temperature sensor
Full text linkWe have proposed a study on single-mode tapered optical fiber for temperature sensing application. A theoretical analysis and its experimental validation were carried out to study the taper profile for highly sensitive temperature sensor. Experiments were performed to observe a wavelength shift of transmission spectra with different taper profiles. The effects of taper profiles on the sensitivity of the sensor were also investigated. Our results indicate that the tapered fiber-based temperature sensor has sensitivity in the range of 0.01143 to 0.03406 nm/C. The findings also demonstrate that the sensor sensitivity can be adjusted with variation to the taper profile
Truncation of the series expressions in the advanced ENZ-theory of diffraction integrals
Full text linkThe point-spread function (PSF) is used in optics for design and assessment of the imaging capabilities of an optical system. It is therefore of vital importance that this PSF can be calculated fast and accurately. In the past 12 years, the Extended Nijboer-Zernike (ENZ) approach has been developed for the purpose of semi-analytic evaluation of the PSF, for circularly symmetric optical systems, in the focal region. In the earliest ENZ-years, the Debye approximation of the diffraction integral, by which the PSF is given, was considered for the very basic situation of a low-NA optical system and relatively small defocus values, so that a scalar treatment was allowed with a focal factor comprising a quadratic function in the exponential. At present, the ENZ-method allows calculation of the PSF in low- and high-NA cases, in scalar form and for vector fields (including polarization), for large wave-front aberrations, including amplitude non-uniformities, using a quasi-spherical phase focal factor in a virtually unlimited focal range around the focal plane, and no limitations in the off-axis direction. Additionally, the application range of the method has been broadened and generalized to the calculation of aerial images of extended objects by including the finite distance of the object to the entrance pupil. Also imaging into a multi-layer is now possible by accounting for both forward and backward propagation in the layers.In the advanced ENZ-approach, the generalized, complex-valued pupil function is developed into a series of Zernike circle polynomials, with exponential azimuthal dependence (having cosine/sine azimuthal dependence as special cases). For each Zernike term, the diffraction integral reduces after azimuthal integration to an integral that can be expressed as an infinite double series involving spherical Bessel functions, accounting for the parameters of the optical system and the defocus value, and Jinc functions comprising the radial off-axis value. The contribution of the present paper is the formulation of truncation rules for these double series expressions, with a general rule valid for all circle polynomials at the same time, and a dedicated rule that takes into account the degree and the azimuthal order of the involved circle polynomials to significantly reduce computational cost in specific cases. The truncation rules are based on effective bounds and asymptotics (of the Debye type) for the mentioned spherical Bessel functions and Jinc functions, and show feasibility of computation of practically all diffraction integrals that one encounters in the ENZ-practice. Thus it can be said that the advanced ENZ-theory is more or less completed from the computational point of view by the achievements of the present paper
High resolution 2-D fluorescence imaging of the mass boundary layer thickness at free water surfaces
Full text linkA novel 2-D fluorescence imaging technique has been developed to visualize the thickness of the aqueous mass boundary layer at a free water surface. Fluorescence is stimulated by high-power LEDs and is observed from above with a low noise, high resolution and high-speed camera. The invasion of ammonia into water leads to an increase in pH (from a starting value of 4), which is visualized with the fluorescent dye pyranine. The flux of ammonia can be controlled by controlling its air side concentration. A higher flux leads to basic pH values (pH > 7) in a thicker layer at the water surface from which fluorescent light is emitted. This allows the investigation of processes affecting the transport of gases in different depths in the aqueous mass boundary layer. In this paper, the chemical system and optical components of the measurement method are presented and its applicability to a wind-wave tank experiment is demonstrated
Polychromatic speckle reduction in laser pico-projectors using stationary dual Hadamard diffusers
Full text linkSpeckle from coherent light sources continues to be a limiting factor in the design and manufacturing of laser projectors. Utilizing diffractive diffusers has been an effective method for reducing monochromatic speckle contrast. Color laser projection devices require the use of red, green, and blue laser sources therefore; using a monochromatic diffractive diffuser may not be optimal for color speckle contrast reduction. A new static dual-diffuser system utilizing Hadamard matrices has been designed to reduce full color speckle. This paper analyzes the effectiveness of the new Hadamard diffusers in reducing speckle using three separate RGB laser diodes. A simulation of the Hadamard diffusers is conducted to determine the optimum spacing between the two diffusers for polychromatic speckle reduction. Experimental measured results are presented using the optimal spacing of Hadamard diffusers for RGB color speckle reduction showing 60% reduction in contras