Advanced Electromagnetics (E-Journal)
Not a member yet
299 research outputs found
Sort by
Frequency Behavior of Conformal Wire Structures
No full textThree-dimensional models are built to examine the frequency behavior of wire structures conforming onto nonplanar surfaces. The effects of altered periodicity on frequency selectiveness of the structures are considered. An analogy is drawn with the antenna impedance behavior of a single active wire surrounded by a number of passive similar ones. Numerical simulations are performed for different wire geometries over a conical surface
Emergence of Classicality from Initial Quantum World for Dissipative Optical Waves
No full textFor light waves propagating in dissipative media, the emergence of classical characteristics from the initial quantum world is investigated. Two classicality measures of the system, which are the measure of the degree of (relative) classical correlation and that of the degree of quantum decoherence are analyzed
Analysis of Reflector Antennas in Radio Telescopes
No full textWe present an analysis on the performance of the Cassegrain and Gregorian on-axis, off-axis and offset antennas. In our study, we have adopted the design parameters for the Cassegrain configuration used in the Atacama Large Millimeter Array (ALMA) project. Modifications on the original parameters are made so as to meet the design requirement for the off-axis and offset configurations. To reduce spillover loss in the offset antennas, we have adjusted the angle between the axis of the primary reflector and that of the sub-reflector, so that the feed horn is placed right next to the edge of the primary reflector. This is to allow the offset antennas to receive the highest power at the feed horn. The results obtained from the physical optics simulation show that the radiation characteristics of both Cassegrain and Gregorian antennas are similar. The offset designs exhibit the best performance, followed by the on-axis, and, finally, the off-axis designs. Our analysis also shows that the performance of both offset Cassegrain and Gregorian antennas are comparable to each other
Application of Teaching Learning Based Optimization in antenna designing
No full textNumerous optimization techniques are studied and applied on antenna designs to optimize various performance parameters. Authors used many Multiple Attributes Decision Making (MADM) methods, which include, Weighted Sum Method (WSM), Weighted Product Method (WPM), Technique for Order Preference by Similarity to Ideal Solution (TOPSIS), Analytic Hierarchy Process (AHP), ELECTRE, etc. Of these many MADM methods, TOPSIS and AHP are more widely used decision making methods. Both TOPSIS and AHP are logical decision making approaches and deal with the problem of choosing an alternative from a set of alternatives which are characterized in terms of some attributes. Analytic Hierarchy Process (AHP) is explained in detail and compared with WSM and WPM. Authors fi- nally used Teaching-Learning-Based Optimization (TLBO) technique; which is a novel method for constrained antenna design optimization problems
Design Formulas for Broadband Concentric Circular-Loops Antennas
No full textThis paper presents a simple formulas for designing broadband concentric circular-loops antennas (CCLAs). The loop dimensions for widest bandwidth are expressented in terms of the resonance frequency of the driven loop. The analysis addresses both cases CCLAs with and without ground planes. The presented formulas are employed to design multiple CCLAs. For example, a 3-elements CCLA of a maximum radius of 6.34 cm can be designed to operate with a voltage standing wave ratio (VSWR) < 2 over a frequencies band of a fractional bandwidth of 16.9% with a minimum directivity of 3.9 dB. Addionationally, a 4-elements CCLA of maximum radius of 15 cm can be design to operate in the frequency band extending from 825 MHz to 991 MHz (fractional bandwidth of 18.3%) with a VSWR < 2 and directivity higher than 5.2 dB over the entire band. Furthermore, the analysis shows that a 3-elements CCLA backed with a conducting ground plane improves the fractional bandwidth to 19.6% and directivity to 9.15 dB over the band of interest. The analytical results on designed antennas are validated with simulation results obtained by using the AN-SOF antenna simulation software. An excellent agreement is observed between analytical and AN-SOF simulations results
All-optical switching using a new photonic crystal directional coupler
No full textIn this paper all-optical switching in a new photonic crystal directional coupler is performed. The structure of the switch consists of a directional coupler and a separate path for a control signal called “control waveguide”. In contrast to the former reported structures in which the directional couplers are made by removing a row of rods entirely, the directional coupler in our optical switch is constructed by two reduced-radius line-defect waveguides separated by the control waveguide. Furthermore, in our case the background material has the nonlinear Kerr property. Therefore, in the structure of this work, no frequency overlap occurs between the control waveguide mode and the directional coupler modes. It is shown that such a condition provides a very good isolation between the control and the probe signals at the output ports. In the control waveguide, nonlinear Kerr effect causes the required refractive index change by the presence of a high power control (pump) signal. Even and odd modes of the coupler are investigated by applying the distribution of the refractive index change in the nonlinear region of a super-cell so that a switching length of about 94 µm is obtained at the wavelength of 1.55 µm. Finally, all-optical switching of the 1.55 µm probe signal using a control signal at the wavelength of 1.3 µm, is simulated through the finite-difference time-domain method, where both signals are desirable in optical communication systems. A very high extinction ratio of 67 dB is achieved and the temporal characteristics of the switch are demonstrated
Modeling the Non Linear Behavior of a Magnetic Fault Current Limiter
No full textFault Current Limiters are used in a wide array of applications from small circuit protection at low power levels to large scale high power applications which require superconductors and complex control circuitry. One advantage of passive fault current limiters (FCL) is the automatic behavior that is dependent on the intrinsic properties of the circuit elements rather than on a complex feedback control scheme making this approach attractive for low cost applications and also where reliability is critical. This paper describes the behavioral modeling of a passive Magnetic FCL and its potential application in practical circuits
Efficient Statistical Extraction of the Per-Unit-Length Capacitance and Inductance Matrices of Cables with Random Parameters
No full textCable bundles often exhibit random parameter variations due to uncertain or uncontrollable physical properties and wire positioning. Efficient tools, based on the so-called polynomial chaos, exist to rapidly assess the impact of such variations on the per-unit-length capacitance and inductance matrices, and on the pertinent cable response. Nevertheless, the state-of-the-art method for the statistical extraction of the per-unit-length capacitance and inductance matrices of cables suffers from several inefficiencies that hinder its applicability to large problems, in terms of number of random parameters and/or conductors. This paper presents an improved methodology that overcomes the aforementioned limitations by exploiting a recently-published, alternative approach to generate the pertinent polynomial chaos system of equations. A sparse and decoupled system is obtained that provides remarkable benefits in terms of speed, memory consumption and problem size that can be dealt with. The technique is thoroughly validated through the statistical analysis of two canonical structures, i.e. a ribbon cable and a shielded cable with random geometry and position
Analytical Solution for Elliptical Cloaks Based on The Frequency Selective Surface
No full textIn this paper the elliptical dielectric cylinder which is covered with FSS cloak is considered. Frequency selective surface cloak which Alu named it mantle cloak is one of the recent techniques for cloaking. In this method an appropriate FSS can act as cloaking device for suppressing the scattering of object in the desired frequency. With using this method the dimension of the cloaks is extremely reduced. By this proposed structure, the RCS of elliptical cylinder is reduced about 10-20 dB and designed cloak has an appropriate performance. The analytical solution for the wave in each layer is presented and with using simulation, the electric field and the scattering pattern has been drawn
Influence of the common mode impedance paths on the design of the EMI filters used with SiC-buck converter
No full textThis paper deals the design of EMI filter associated with buck converter using fast semiconductors silicon carbide SiC (diode and transistor JFET). To comply with EMC standards, a filter design method based on an equivalent electrical circuit is proposed. The aim is to identify the different values of the EMI filter elements but also to obtain the limits values of the parasitic elements of the passive components which have a major influence on the attenuation of the filters. The purpose is to study the influence of the modification of the common mode propagation paths before and after the installation of the filter. A solution is also proposed to reduce the conducted disturbances that occur at high frequency caused by the fast SiC components.The comparison of the simulation results with the measurements data carried out on a DC-DC converter without and with the EMI filter, shows the effectiveness of the proposed design approach