130 research outputs found
Tip-leakage losses in subsonic and transonic blade rows
No full textIn this paper the effect of blade-exit Mach number on unshrouded turbine tip-leakage flows is investigated. Previously published experimental data of a high-pressure turbine blade are used to validate a computational fluid dynamics (CFD) code, which is then used to study the tip-leakage flow at blade-exit Mach numbers from 0.6 to 1.4. Three-dimensional (3D) calculations are performed of a flat-tip and a cavity-tip blade. Two-dimensional calculations are also performed to show the effect of various squealer-tip geometries on an idealized tip flow. The results show that as the blade-exit Mach number is increased the tip-leakage flow becomes choked. Therefore the tip-leakage flow becomes independent of the pressure difference across the tip and hence the blade loading. Thus the effect of the tip-leakage flow on overall blade loss reduces at blade-exit Mach numbers greater than 1.0. The results suggest that for transonic blade rows it should be possible to raise blade loading within the tip region without increasing tip-leakage los
Physics on tap
No full textThis article aims to describe how to visualize surface tension effects in liquid jets. A simple experiment is proposed using the liquid jet flow from a mains water tap/faucet. Using a modern digital camera with a high shutter speed, it is possible to visualize the instabilities (capillary waves) that form within the jet due to the action of surface tension, which can then eventually lead to droplet formation. Visualizing this process is important for understanding the fluid mechanics of liquid jets and also the formation of droplets, which has wide applications for instance in printing, polymer processing, aerosol sprays and fuel injection in combustion chambers.<br/
The role of dense gas dynamics on organic rankine cycle turbine performance
No full textIn this paper we investigate the real gas flows which occur within Organic Rankine Cycle (ORC) turbines. A new method for the design of nozzles operating with dense gases is discussed, and applied to the case of a high pressure ratio turbine vane. A Navier-Stokes method which uses equations of states for a variety of working fluids typical of ORC turbines is then applied to the turbine vanes to determine the vane performance. The results suggest that the choice of working fluid has a significant influence on the turbine efficiency
Compressor wake/leading-edge interactions at off design incidences
No full textIn this paper, the effects of wake/leading-edge interactions were studied at off-design conditions. Measurements were performed on the stator-blade suction surface at midspan. The leading-edge flow-field was investigated using hotwire micro-traverses, hotfilm surface shear-stress sensors and pressure micro-tappings. The trailing-edge flow-field was investigated using hotwire boundary-layer traverses. Unsteady CFD calculations were also performed to aid the interpretation of the results. At low flow coefficients, the time-averaged momentum thickness of the leading-edge boundary layer was found to rise as the flow coefficient was reduced. The time-resolved momentum-thickness rose due to the interaction of the incoming rotor wake. As the flow coefficient was reduced, the incoming wakes increased in pitch-wise extent, velocity deficit and turbulence intensity. This increased both the time-resolved rise in the momentum thickness and the turbulent spot production within the wake affected boundary-layer. Close to stall, a drop in the leading-edge momentum thickness was observed in-between wake events. This was associated with the formation of a leading-edge separation bubble in-between wake events. The wake interaction with the bubble gave rise to a shedding phenomenon, which produced large length scale disturbances in the surface shear stres
The effect of wake induced structures on compressor boundary-layers
No full textThe interaction of a convected wake with a compressor blade boundary layer was investigated. Measurements within a single-stage compressor were made using an endoscopic PIV system, a surface mounted pressure transducer, hotfilms and hotwire traverses, along with CFD simulations. The wake/leading-edge interaction was shown to lead to the formation of a thickened laminar boundary-layer, within which turbulent spots formed close to the leading edge. The thickened boundary-layer became turbulent and propagated down the blade surface, giving rise to pressure perturbations of 7% of the inlet dynamic head in magnitude. The results indicate that wake/leading-edge interactions have a crucial role to play in the performance of compressor blades in the presence of wakes
Turbine blade tip heat transfer in low speed and high speed flows
No full textIn this paper, high and low speed tip flows are investigated for a high-pressure turbine blade. Previous experimental data are used to validate a CFD code, which is then used to study the tip heat transfer in high and low speed cascades. The results show that at engine representative Mach numbers the tip flow is predominantly transonic. Thus, compared to the low speed tip flow, the heat transfer is affected by reductions in both the heat transfer coefficient and the recovery temperature. The high Mach numbers in the tip region (M>1.5) lead to large local variations in recovery temperature. Significant changes in the heat transfer coefficient are also observed. These are due to changes in the structure of the tip flow at high speed. At high speeds, the pressure side corner separation bubble reattachment occurs through supersonic acceleration which halves the length of the bubble when the tip gap exit Mach number is increased from 0.1 to 1.0. In addition, shock/boundary-layer interactions within the tip gap lead to large changes in the tip boundary-layer thickness. These effects give rise to significant differences in the heat-transfer coefficient within the tip region compared to the low-speed tip flow. Compared to the low speed tip flow, the high speed tip flow is much less dominated by turbulent dissipation and is thus less sensitive to the choice of turbulence model. These results clearly demonstrate that blade tip heat transfer is a strong function of Mach number, an important implication when considering the use of low speed experimental testing and associated CFD validation in engine blade tip desig
Experimental investigation into unsteady effects on film cooling
No full textThe benefits of different film cooling geometries are typically assessed in terms of their time-averaged performance. It is known that the mixing between the coolant film and the main turbine passage flow is an unsteady process. The current study investigates the forms of unsteadiness that occur in engine-representative film cooling flows and how this unsteadiness affects the mixing with the mainstream flow. Cylindrical and fan-shaped cooling holes across a range of hole blowing ratios have been studied experimentally using particle image velocimetry and high speed photography. Coherent unsteadiness is found in the shear layer between the jet and the mainstream for both cylindrical and fan-shaped cooling holes. Its occurrence and sense of rotation is found to be controlled by the velocity difference between the mainstream flow and the jet, which is largely determined by the blowing ratio
Turbine blade tip heat transfer in low speed and high speed flows
No full textIn this paper, high and low speed tip flows are investigated for a high-pressure turbine blade. Previous experimental data are used to validate a computational fluid dynamics (CFD) code, which is then used to study the tip heat transfer in high and low speed cascades. The results show that at engine representative Mach numbers, the tip flow is predominantly transonic. Thus, compared with the low speed tip flow, the heat transfer is affected by reductions in both the heat-transfer coefficient and the recovery temperature. The high Mach numbers in the tip region (M>1.5) lead to large local variations in recovery temperature. Significant changes in the heat-transfer coefficient are also observed. These are due to changes in the structure of the tip flow at high speed. At high speeds, the pressure side corner separation bubble reattachment occurs through supersonic acceleration, which halves the length of the bubble when the tip-gap exit Mach number is increased from 0.1 to 1.0. In addition, shock/boundary-layer interactions within the tip gap lead to large changes in the tip boundary-layer thickness. These effects give rise to significant differences in the heat-transfer coefficient within the tip region compared with the low speed tip flow. Compared with the low speed tip flow, the high speed tip flow is much less dominated by turbulent dissipation and is thus less sensitive to the choice of turbulence model. These results clearly demonstrate that blade tip heat transfer is a strong function of Mach number, an important implication when considering the use of low speed experimental testing and associated CFD validation in engine blade tip design
- …
