78 research outputs found
Utilization of three-layers heterogeneous mammographic phantom through MCNPX code for breast and chest radiation dose levels at different diagnostic X-ray energies: A Monte Carlo simulation study
No full textIntroduction: We report the breast and chest radiation dose assessment for mammographic examinations using a three-layer heterogeneous breast phantom through the MCNPX Monte Carlo code. Methods: A three-layer heterogeneous phantom along with compression plates and X-ray source are modeled. The validation of the simulation code is obtained using the data of AAPM TG-195 report. Deposited energy amount as a function of increasing source energy is calculated over a wide energy range. The behavioral changes in X-ray absorption as well as transmission are examined using the F6 Tally Mesh extension of MCNPX code. Moreover, deposited energy amount is calculated for modeled body phantom in the same energy range. Results and discussions: The diverse distribution of glands has a significant impact on the quantity of energy received by the various breast layers. In layers with a low glandular ratio, low-energy primary X-ray penetrability is highest. In response to an increase in energy, the absorption in layers with a low glandular ratio decreased. This results in the X-rays releasing their energy in the bottom layers. Additionally, the increase in energy increases the quantity of energy absorbed by the tissues around the breast. Copyright © 2023 ALMisned, Elshami, Kilic, Rabaa, Zakaly, Ene and Tekin.Universitatea 'Dunărea de Jos' Galați, UDJG; Princess Nourah Bint Abdulrahman University, PNUPrincess Nourah Bint Abdulrahman University Researchers Supporting Project Number (PNURSP2023R149), Princess Nourah Bint Abdulrahman University, Riyadh, Saudi Arabia.The authors would like to express their deepest gratitude to Princess Nourah Bint Abdulrahman University Researchers Supporting Project Number (PNURSP2023R149), Princess Nourah Bint Abdulrahman University, Riyadh, Saudi Arabia. The author AE acknowledges the support of Dunarea de Jos University of Galati
ASO Author Reflections: Isolated Margin Positivity in Localized Pancreatic Ductal Adenocarcinoma and Operative Margin Revision.
No full textImpact of Eye and Breast Shielding on Organ Doses During Cervical Spine Radiography: Design and Validation of MIRD Computational Phantom
No full textPurpose: The study aimed to design and validate computational phantoms (MIRD) using the MCNPX code to assess the impact of shielding on organ doses. Method: To validate the optimized phantom, the obtained results were compared with experimental results. The validation of the optimized MIRD phantom was provided by using the results of a previous anthropomorphic phantom study. MIRD phantom was designed by considering the parameters used in the anthropomorphic phantom study. A test simulation was performed to compare the dose reduction percentages (%) between the experimental anthropomorphic phantom study and the MCNPX-MIRD phantom. The simulation was performed twice, with and without shielding materials, using the same number and locations of the detector. Results: The absorbed dose amounts were directly extracted from the required organ and tissue cell parts of output files. Dose reduction percentages between the simulation with shielding and simulation without shielding were compared. The highest dose reduction was noted in the thymus (95%) and breasts (88%). The obtained dose reduction percentages between the anthropomorphic phantom study and the MCNPX-MIRD phantom were highly consistent and correlated values with experimental anthropomorphic data. Both methods showed Relative Difference (%) ranges between 0.88 and 2.22. Moreover, the MCNPX-MIRD optimized phantom provides detailed dose analysis for target and non-target organs and can be used to assess the efficiency of shielding in radiological examination. Conclusion: Shielding breasts and eyes during cervical radiography reduced the radiation dose to many organs. The decision to not shield patients should be based on research evidence as this approach does not apply to all cases. Copyright © 2021 Elshami, Tekin, Issa, Abuzaid, Zakaly, Issa and Ene.The APC was supported by Dunarea de Jos University of Galati, Romania
MEASUREMENTS OF RADIATION EXPOSURE OF RADIOGRAPHY STUDENTS DURING THEIR CLINICAL TRAINING USING THERMOLUMINESCENT DOSIMETRY
No full text
Experimentally evaluation of high-performance concrete mixes used for tunnels and containing silica fume and polypropylene fiber after exposed to high temperatures
No full textThis work introduces an experimental study to evaluate the effect of elevated temperatures on the mechanical properties of high-performance concrete (HPC) mix with changes in Water-Cementitious ratios, W/(C+SF), Silica Fume percent, SF, and Polypropylene, PP, fiber contents. This mix was typically designed to satisfy the requirements of tunnel concrete. The compressive and indirect tensile strengths were measured at room temperature, RT, and after exposure to 400�C and 800�C. Moreover, SEM micrograph and EDS spot analysis tests were done to evaluate the effect of elevated temperatures. Fifteen mixes of HPC with different ratios of W/(C+SF), SF, and PP fiber were tested. According to the test results, the compressive strength values of design mixes increased significantly after exposure to 400�C. Moreover, using SF = 10%, the results indicated remarkable improvements in the compressive strength at 400�C and 800�C, in the case of the W/(C+SF) ratio of 0.31. On the other hand, the highest effect of the presence of PP fibers was 0.211, depending on variable ratios of the W/(C+SF) ratio and the SF content. In the case of PP=0.106 and SF=10%, the mass loss was higher at exposure to temperatures of 800�
Experimentally evaluation of high-performance concrete mixes used for tunnels and containing silica fume and polypropylene fiber after exposed to high temperatures
No full textThis work introduces an experimental study to evaluate the effect of elevated temperatures on the mechanical properties of high-performance concrete (HPC) mix with changes in Water-Cementitious ratios, W/(C+SF), Silica Fume percent, SF, and Polypropylene, PP, fiber contents. This mix was typically designed to satisfy the requirements of tunnel concrete. The compressive and indirect tensile strengths were measured at room temperature, RT, and after exposure to 400°C and 800°C. Moreover, SEM micrograph and EDS spot analysis tests were done to evaluate the effect of elevated temperatures. Fifteen mixes of HPC with different ratios of W/(C+SF), SF, and PP fiber were tested. According to the test results, the compressive strength values of design mixes increased significantly after exposure to 400°C. Moreover, using SF = 10%, the results indicated remarkable improvements in the compressive strength at 400°C and 800°C, in the case of the W/(C+SF) ratio of 0.31. On the other hand, the highest effect of the presence of PP fibers was 0.211, depending on variable ratios of the W/(C+SF) ratio and the SF content. In the case of PP=0.106 and SF=10%, the mass loss was higher at exposure to temperatures of 800°C
Experimentally evaluation of high-performance concrete mixes used for tunnels and containing silica fume and polypropylene fiber after exposed to high temperatures
No full textThis work introduces an experimental study to evaluate the effect of elevated temperatures on the mechanical properties of high-performance concrete (HPC) mix with changes in Water-Cementitious ratios, W/(C+SF), Silica Fume percent, SF, and Polypropylene, PP, fiber contents. This mix was typically designed to satisfy the requirements of tunnel concrete. The compressive and indirect tensile strengths were measured at room temperature, RT, and after exposure to 400°C and 800°C. Moreover, SEM micrograph and EDS spot analysis tests were done to evaluate the effect of elevated temperatures. Fifteen mixes of HPC with different ratios of W/(C+SF), SF, and PP fiber were tested. According to the test results, the compressive strength values of design mixes increased significantly after exposure to 400°C. Moreover, using SF = 10%, the results indicated remarkable improvements in the compressive strength at 400°C and 800°C, in the case of the W/(C+SF) ratio of 0.31. On the other hand, the highest effect of the presence of PP fibers was 0.211, depending on variable ratios of the W/(C+SF) ratio and the SF content. In the case of PP=0.106 and SF=10%, the mass loss was higher at exposure to temperatures of 800°C
Experimentally evaluation of high-performance concrete mixes used for tunnels and containing silica fume and polypropylene fiber after exposed to high temperatures
No full textThis work introduces an experimental study to evaluate the effect of elevated temperatures on the mechanical properties of high-performance concrete (HPC) mix with changes in Water-Cementitious ratios, W/(C+SF), Silica Fume percent, SF, and Polypropylene, PP, fiber contents. This mix was typically designed to satisfy the requirements of tunnel concrete. The compressive and indirect tensile strengths were measured at room temperature, RT, and after exposure to 400°C and 800°C. Moreover, SEM micrograph and EDS spot analysis tests were done to evaluate the effect of elevated temperatures. Fifteen mixes of HPC with different ratios of W/(C+SF), SF, and PP fiber were tested. According to the test results, the compressive strength values of design mixes increased significantly after exposure to 400°C. Moreover, using SF = 10%, the results indicated remarkable improvements in the compressive strength at 400°C and 800°C, in the case of the W/(C+SF) ratio of 0.31. On the other hand, the highest effect of the presence of PP fibers was 0.211, depending on variable ratios of the W/(C+SF) ratio and the SF content. In the case of PP=0.106 and SF=10%, the mass loss was higher at exposure to temperatures of 800°C
Perceptions of E-portfolio Use in Lifelong Learning and Professional Development Among Radiology Professionals
No full text- …
