86,633 research outputs found
Standardized loads acting in knee implants
No full textThe loads acting in knee joints must be known for improving joint replacement, surgical procedures, physiotherapy, biomechanical computer simulations, and to advise patients with osteoarthritis or fractures about what activities to avoid. Such data would also allow verification of test standards for knee implants. This work analyzes data from 8 subjects with instrumented knee implants, which allowed measuring the contact forces and moments acting in the joint. The implants were powered inductively and the loads transmitted at radio frequency. The time courses of forces and moments during walking, stair climbing, and 6 more activities were averaged for subjects with I) average body weight and average load levels and II) high body weight and high load levels. During all investigated activities except jogging, the high force levels reached 3,372–4,218N. During slow jogging, they were up to 5,165N. The peak torque around the implant stem during walking was 10.5 Nm, which was higher than during all other activities including jogging. The transverse forces and the moments varied greatly between the subjects, especially during non-cyclic activities. The high load levels measured were mostly above those defined in the wear test ISO 14243. The loads defined in the ISO test standard should be adapted to the levels reported here. The new data will allow realistic investigations and improvements of joint replacement, surgical procedures for tendon repair, treatment of fractures, and others. Computer models of the load conditions in the lower extremities will become more realistic if the new data is used as a gold standard. However, due to the extreme individual variations of some load components, even the reported average load profiles can most likely not explain every failure of an implant or a surgical procedure
Hip contact forces and gait patterns from routine activities
No full textIn vivo loads acting at the hip joint have so far only been measured in few patients and without detailed documentation of gait data. Such information is required to test and improve wear, strength and fixation stability of hip implants. Measurements of hip contact forces with instrumented implants and synchronous analyses of gait patterns and ground reaction forces were performed in four patients during the most frequent activities of daily living. From the individual data sets an average was calculated. The paper focuses on the loading of the femoral implant component but complete data are additionally stored on an associated compact disc. It contains complete gait and hip contact force data as well as calculated muscle activities during walking and stair climbing and the frequencies of daily activities observed in hip patients. The mechanical loading and function of the hip joint and proximal femur is thereby completely documented. The average patient loaded his hip joint with 238% BW (percent of body weight) when walking at about 4 km/h and with slightly less when standing on one leg. This is below the levels previously reported for two other patients (Bergmann et al., Clinical Biomechanics 26 (1993) 969-990). When climbing upstairs the joint contact force is 251% BW which is less than 260% BW when going downstairs. Inwards torsion of the implant is probably critical for the stem fixation. On average it is 23% larger when going upstairs than during normal level walking. The inter- and intra-individual variations during stair climbing are large and the highest torque values are 83% larger than during normal walking. Because the hip joint loading during all other common activities of most hip patients are comparably small (except during stumbling), implants should mainly be tested with loading conditions that mimic walking and stair climbing
Realistic loads for testing hip implants
No full textThe aim here was to define realistic load conditions for hip implants, based on in vivo contact force measurements, and to see whether current ISO standards indeed simulate real loads. The load scenarios obtained are based on in vivo hip contact forces measured in 4 patients during different activities and on activity records from 31 patients. The load scenarios can be adapted to various test purposes by applying average or high peak loads, high-impact activities or additional low-impact activities, and by simulating normal or very active patients. The most strenuous activities are walking (average peak forces 1800 N, high peak forces 3900 N), going up stairs (average peak forces 1900 N, high peak forces 4200 N) and stumbling (high peak forces 11,000 N). Torsional moments are 50% higher for going up stairs than for walking. Ten million loading cycles simulate an implantation time of 3.9 years in active patients. The in vitro fatigue properties of cementless implant fixations are exceeded during stumbling. At least for heavyweight and very active subjects, the real load conditions are more critical than those defined by the ISO standards for fatigue tests
A hip implant energy harvester
No full textThis paper presents a kinetic energy harvester designed to be embedded in a hip implant which aims to operate at a low frequency associated with body motion of patients. The prototype is designed based on the constrained volume available in a hip prosthesis and the challenge is to harvest energy from low frequency movements (< 1 Hz) which is an average frequency during free walking of a patient. The concept of magnetic-force-driven energy harvesting is applied to this prototype considering the hip movements during routine activities of patients. The magnetic field within the harvester was simulated using COMSOL. The simulated resonant frequency was around 30 Hz and the voltage induced in a coil was predicted to be 47.8 mV. A prototype of the energy harvester was fabricated and tested. A maximum open circuit voltage of 39.43 mV was obtained and the resonant frequency of 28 Hz was observed. Moreover, the power output of 0.96 ?W was achieved with an optimum resistive load of 250
Variations on the Author
No full text“Variations on the Author” discusses two of Eduardo Coutinho’s recent films (Um Dia na Vida, from 2010, and Últimas Conversas, posthumously released in 2015) and their contribution to the general question of documentary authorship. The director’s filmography is characterized by a consistent yet self-effacing form of authorial self-inscription: Coutinho often features as an interviewer that rather than express opinions propels discourses; an interviewer that is good at listening. This mode of self-inscription characterizes him as an author who is not expressive but who is nonetheless markedly present on the screen. In Um Dia na Vida, however, Coutinho is completely absent form the image, while Últimas Conversas, on the contrary, includes a confessional prologue that moves the director from the margins to the center of his films. This article examines the ways in which these works stand out in the filmography of a director who offers new insights into the notion of cinematic authorship
[Newspaper Clipping: Author Claims Evidence of Second JFK Assassin #1]
No full textNewspaper article titled "Author Claims Evidence of Second JFK Assassin." The article states that author Richard J. Whalen concluded "that there is circumstantial evidence to support the theory of a second assassin in the shooting of President John F. Kennedy.
Also By The Same Author: AKTiveAuthor, a Citation Graph Approach to Name Disambiguation
No full textThe desire for definitive data and the semantic web drive for inference over heterogeneous data sources requires co-reference resolution to be performed on those data. In particular, name disambiguation is required to allow accurate publication lists, citation counts and impact measures to be determined. This paper describes a graph-based approach to author disambiguation on large-scale citation networks. Using self-citation, co-authorship and document source analyses, AKTiveAuthor clusters papers, achieving precision of 0.997 and recall of 0.818 over a test group of eight surname clusters
John F. Kennedy telegram to Roosevelt
No full textJersey Homesteads (later the Borough of Roosevelt) was established in the 1930s as an agro-industrial cooperative community. It was established specifically for urban Jewish garment workers, many of whom had emigrated from Europe. President John F. Kennedy sent a telegram to the citizens of Roosevelt, New Jersey, apologizing for not being able to attend the memorial dedication in honor of former President Franklin Delano Roosevelt. (Jersey Homesteads became Roosevelt in 1945 in honor of the president.) President Kennedy expressed his gratitude to the people of Roosevelt for constructing the memorial, and commented that it will serve as a constant reminder of Roosevelt's good works
Logarithmic variance profiles and the corresponding f-1 spectra of temperature fluctuations in turbulent Rayleigh-Bénard convection
No full textWe report experimental results for the temperature variance 2(z) and the corresponding frequency spectra P(f) in turbulent Rayleigh-Bénard convection (RBC) in a cylindrical sample of aspect ratioT= D/L = 1:00 (D = 1:12 m is the diameter and L = 1:12 m the height). The measurements were conducted in the Rayleigh-number range 1011 < Ra < 1:35 1014 and Pr ' 0:8. For Ra = 1:35x1014, 2(z) could be described well by a logarithmic dependence on the vertical position z in a range of z 1 < z < z 2 with z 1 ' 70 and z 2 = 0:1L. Here L=(2Nu) is the thickness of a thin thermal sublayer adjacent to the horizontal plate where the heat flux (denoted by the Nusselt number Nu) is carried mostly by thermal diffusion. In the log layer, we found that the temperature spectra had a significant frequency range over which P(f) f with close to 1. As Ra decreased, increased so that the log layer became thinner. At Ra = 2:05 1011, z 2 < z 1 and therefore there was no range for a log layer. Correspondingly, the temperature spectrum near the horizontal plate did not have the f1 scaling form either
Maine author Franklin F. Gould recalls his first glimpse of the outside world
No full textMaine author Franklin F. Gould recalls his first glimpse of the outside world as he relates how, as a young farm boy in the late 1800\u27s, he drove his father\u27s horses on an errand to an icebound river
- …
