112,792 research outputs found
Mechanical properties updating of a non-uniform natural fibre composite panel by means of a parallel genetic algorithm
No full textThis article presents an investigation on the mechanical properties of a composite panel made of unidirectional flax fibres embedded in a polyethylene matrix (flax-PE). An initial set of mechanical properties was identified by classical static tests. Then, an experimental modal analysis was performed in order to get information on natural frequencies and mode shapes, which are related to the mechanical properties. The experimental modal results were compared with numerical ones, obtained through finite element model using the initial set of mechanical properties. Finally, in order to get a good numerical-experimental correlation, the mechanical properties throughout the panel were updated using an inverse modelling method based on parallel genetic algorithms
Acquisizione su strada dei carichi al tubo reggisella di telai di mtb biammortizzate e verifica a fatica ad ampiezza variabile
No full textAcquisizione su strada dei carichi al tubo reggisella di telai di mtb biammortizzate e verifica a fatica ad ampiezza variabile
No full textSafe design of Y-shaped MTB frames after field data collection and variable amplitude fatigue testing
No full textAnalysis of Polynomial-Phase Signals by an Integrated Generalized Ambiguity Function
No full textThe aim of this work is the performance analysis of a method for the detection and parameter estimation of mono or multicomponent polynomial-phase signals (PPS) embedded in white Gaussian noise and based on a generalized ambiguity function. The proposed method is shown to be asymptotically efficient for second-order PPS and nearly asymptotically efficient for third-order PPSs. The method presents some advantages with respect to similar techniques, like the polynomial-phase transform, for example, in terms of (i) a closer approach to the Cramer-Rao lower bounds, (ii) a lower SNR threshold, (iii) a better capability of discriminating multicomponent signal
Torsion loads on a ski-touring boot sole during uphill climbing and downhill skiing
No full textIntroduction: Ski-touring is a well settled winter activity in mountain regions. Differently to alpine skiing, the high ground is reached by climbing the mountain using sealskins under the skis and special boots and bindings. This difference introduces higher concerns on the weight of the equipment rather than other skiing disciplines. Nevertheless, to allow a safe and enjoyable skiing the structural properties of the boot must be guaranteed. Past studies aimed to determine loads and stiffness of alpine and cross-country skiboots using in field or laboratory approaches [1,2,3]. The present study aims to provide an estimation of the torsion loads acting on the ski-touring boot sole during walking and skiing phases. Such measure is helpful towards the design of more performant ski-touring boots.
Methods: A ski-touring boot (left side, size: 26.5 MP) was prepared with strain gauge bridges and calibrated using a servohydraulic machine (Fig 1a). First, the outer rubber sole was cut to reach the plastics of the boot shell. Then, two full Wheatstone bridge were placed on the sole in middle length of the boot to measure torsion and flexion loads.
To calibrate the boot sole close to in-field testing conditions, a silicone dummy foot was fitted inside the boot. Then, the skiboot was mounted on ski-touring bindings surrogates attached to a servohydraulic torsion machine. The torsion channel was calibrated by applying a quasi-static ramp between -5/+5°, reading the applied torque and bridge output synchronously to obtain the bridge sensitivity.
The in-field test took place in Val di Zoldo (BL, Italy), outside temperature was 10 °C, on a slope covered by spring snow. The instrumented boot was connected to a SoMat eDAQ lite data acquisition system (HBM) powered with a 12 V battery, instrumentation was fitted in a small backpack (total weight: 3 kg). Data were acquired at a 500 Hz sampling rate.
Tests were performed by an amateur skier (height: 175 cm, weight: 70 kg, age: 25 yr) who climbed and skied an off-piste route graded BS in Blachère scale. The participant performed a 400 m gain uphill climbing which was divided into straight climb, and left/right side traverses. During the descent the participant was asked to perform narrow and wide slaloms at its own typical speed. Overall length of the test was 45 minutes.
Peak and valleys of data were computed and averaged for each phase to obtain the range of the load. The mean of the signal during each phase was also computed. Internal rotating torques applied to the boot front are positive.
Results and discussion: Calibration trials gave a bridge sensitivity of -12.59 Nm/(mV/V) with an applied torque ranging from -50 to +50 Nm. In field test data (Fig 1b, Table 1) evidenced highest torque ranges during skiing phase; torque mean values showed opposite sign in the two sides of uphill climbing. In both phases the range was well below the torque reached during the calibration trials.
This suggests that ski-touring boot torsion loads should be based on maximal values collected during skiing trials. The analysis and implementation of further measurement channels such as the sole flexion and the ski/walk links will be performed to improve the understanding of climbing and skiing loads. More tests are being conducted to account for subject variability and snow/terrain conditions.
1. Petrone N., Marcolin G., Centofante E., Atzori B. (2010), Analysis of the structural behavior of an innovative reinforced ski boot. Procedia Engineering. 2. 2599-2604. 10.1016/j.proeng.2010.04.038.
2. Petrone N., Marcolin G., Panizzolo F., (2013), The effect of boot stiffness on field and laboratory flexural behavior of alpine ski boots. Sports Engineering. 16. 10.1007/s12283-013-0133-z.
3. Hladnik J. Resman F. Jerman B. (2012), Torsion stiffness of a racing cross-country ski boot. Proceedings of the Institution of Mechanical Engineers Part P Journal of Sports Engineering and Technology
Optimization of a Formula 1 Wheel Assembly using CFD and Mesh Morphing Technology on Certainty
No full textThe geometrical uncertainty associated with a rotating rubber tire can greatly influence the optimal race car setup for a particular track. We quantify this uncertainty by creating up to 20,000 unique 3D wheel configurations that span an input space of multiple uncertain and design parameters. The aerodynamic characteristics of each wheel configuration, consisting of 30 million cells, is solved numerically using Computational Fluid Dynamics (CFD) on Certainty. Every configuration is slightly modified by morphing the mesh locally depending on the multi-objective optimization algorithm
The New Muscovite cultural history : a collection in honor of Daniel B. Rowland, édition V. Kivelson, K. Petrone, N. Shields Kollmann, M. S. Flier
No full textGonneau Pierre. The New Muscovite cultural history : a collection in honor of Daniel B. Rowland, édition V. Kivelson, K. Petrone, N. Shields Kollmann, M. S. Flier. In: Revue des études slaves, tome 82, fascicule 2, 2011. pp. 331-332
The New Muscovite cultural history : a collection in honor of Daniel B. Rowland, édition V. Kivelson, K. Petrone, N. Shields Kollmann, M. S. Flier
No full textGonneau Pierre. The New Muscovite cultural history : a collection in honor of Daniel B. Rowland, édition V. Kivelson, K. Petrone, N. Shields Kollmann, M. S. Flier. In: Revue des études slaves, tome 82, fascicule 2, 2011. pp. 331-332
- …
