27 research outputs found
Electrically injected photonic-crystal nanocavities
No full textNano-emitters are the new generation of laser devices. A photonic-crystal cavity, which highly confines light in small volumes, in combination with quantum-dots can enhance the efficiency and lower the threshold of this device. The practical realisation of a reliable, electrically pumped photonic-crystal laser at room-temperature is, however, challenging.
In this project, a design for such a laser was established. Its properties are split up into electrical, optical and thermal tasks that are individually investigated via various device simulations. The resulting device performance showed that with our design the quantum-dots can be pumped in order to provide gain and to overcome the loss of the system. Threshold currents can be as low as 10’s of μA and Q-factors in the range of 1000’s. Gallium arsenide wafers were grown according to our specifications and their diode behaviour confirmed. Photonic-crystal cavities were fabricated through a newly developed process based on a TiOₓ hard-mask. Beside membraned cavities, also cavities on oxidised AlGaAs were fabricated with help to a unique hard-mask removal method. The cavities were measured with a self-made micro-photoluminescence setup with the highest Q-factor of 4000 for the membrane cavity and a remarkable 2200 for the oxide cavity. The fabrication steps, regarding the electrically pumped photonic-crystal laser, were developed and it was shown that this device can be fabricated.
During this project, a novel type of gentle confinement cavity was developed, based on the adaption of the dispersion curve (DA cavity) of a photonic-crystal waveguide. Q-factors of as high as 600.000 were measured for these cavities made in Silicon
Development of Double and Triple-Pulsed 2-micron IPDA Lidars for Column CO2 Measurements
No full textCarbon dioxide (CO2) is an important greenhouse gas that significantly contributes to the carbon cycle and globalradiation budget on Earth. CO2 role on Earths climate is complicated due to different interactions with various climatecomponents that include the atmosphere, the biosphere and the hydrosphere. Although extensive worldwide efforts formonitoring atmospheric CO2 through various techniques, including in-situ and passive sensors, are taking place highuncertainties exist in quantifying CO2 sources and sinks. These uncertainties are mainly due to insufficient spatial andtemporal mapping of the gas. Therefore it is required to have more rapid and accurate CO2 monitoring with higheruniform coverage and higher resolution. CO2 DIAL operating in the 2-m band offer better near-surface CO2measurement sensitivity due to the intrinsically stronger absorption lines. For more than 15 years, NASA LangleyResearch Center (LaRC) contributed in developing several 2-m CO2 DIAL systems and technologies. This paperfocuses on the current development of the airborne double-pulsed and triple-pulsed 2-m CO2 integrated pathdifferential absorption (IPDA) lidar system at NASA LaRC. This includes the IPDA system development andintegration. Results from ground and airborne CO2 IPDA testing will be presented. The potential of scaling suchtechnology to a space mission will be addressed
Flight Demonstration of a 2-Micron, Double Plused CO2 IPDA Lidar Instrument
No full textNASA Langley Research Center (LaRC) developed a double pulsed, high energy 2-micron Integrated Path Differential Absorption (IPDA) lidar instrument to measure atmospheric CO2 column density. The 2-μm double pulsed IPDA lidar was flown ten times in March and April of 2014. It was determined that the IPDA lidar measurement is in good agreement with an in-situ CO2 measurement by a collocated NOAA flight. The average column CO2 density difference between the IPDA lidar measurements and the NOAA air samples is 1.48ppm in the flight altitudes of 3 to 6.1 km
2.5 MHz Line-Width High-energy, 2 Micrometer Coherent Wind Lidar Transmitter
No full text2 micron solid-state lasers are the primary choice for coherent Doppler wind detection. As wind lidars, they are used for wake vortex and clear air turbulence detection providing air transport safety. In addition, 2 micron lasers are one of the candidates for CO2 detection lidars. The rich CO2 absorption line around 2 micron, combined with the long upper state life of time, has made Ho based 2 micron lasers a viable candidate for CO2 sensing DIAL instrument. The design and fabrication of a compact coherent laser radar transmitter for Troposphere wind sensing is under way. This system is hardened for ground as well as airborne applications. As a transmitter for a coherent wind lidar, this laser has stringent spectral line width and beam quality requirements. Although the absolute wavelength does not have to be fixed for wind detection, to maximize return signal, the output wavelength should avoid atmospheric CO2 and H2O absorption lines. The base line laser material is Ho:Tm:LuLF which is an isomorph of Ho:Tm:YLF. LuLF produces 20% more output power than Ho:Tm:YLF. In these materials the Tm absorption cross-section, the Ho emission cross-section, the Tm to Ho energy transfer parameters and the Ho (sup 5) I (sub 7) radiative life time are all identical. However, the improved performance of the LuLF is attributed to the lower thermal population in the (sup 5) I (sub 8) manifold. It also provides higher normal mode to Q-switch conversion than YLF at high pump energy indicating a lower up-conversion. The laser architecture is composed of a seed laser, a ring oscillator, and a double pass amplifier. The seed laser is a single longitudinal mode with a line width of 13 KHz. The 100mJ class oscillator is stretched to 3 meters to accommodate the line-width requirement without compromising the range resolution of the instrument. The amplifier is double passed to produce greater than 300mJ energy
Flight Demonstration of a 2-Micron, Double Plused CO
No full textNASA Langley Research Center (LaRC) developed a double pulsed, high energy 2-micron Integrated Path Differential Absorption (IPDA) lidar instrument to measure atmospheric CO2 column density. The 2-μm double pulsed IPDA lidar was flown ten times in March and April of 2014. It was determined that the IPDA lidar measurement is in good agreement with an in-situ CO2 measurement by a collocated NOAA flight. The average column CO2 density difference between the IPDA lidar measurements and the NOAA air samples is 1.48ppm in the flight altitudes of 3 to 6.1 km
